• Explosives and Blasting
• /
• v.32 no.3
• /
• pp.10-17
• /
• 2014

In this study, the effect of the hole spacing and the detonation delay time in the long hole blasting of two free surface rock mass on the variation of the principal strains in the vicinity of blasting holes is investigated by use of the finite element program, Visual FEA. The cross section perpendicular to blasting holes is modelled and the maximum principal strains at some major points in the cracking zone are examined. As a result, it was found that the maximum principal strain in the cracking zone becomes larger in the long hole blasting with the narrower hole spacing and the longer detonation delay time. The maximum principal strain was affected by the detonation position in charge hole.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4D
• /
• pp.491-497
• /
• 2009

This paper presents the results of accelerated pavement tests (APT) that simulate permanent deformation (rutting) of asphalt concrete pavements under different temperatures and loading courses. Also, finite element (FE) analysis has been conducted to predict the test results. Test section for APT is the same as one of test sections at Korea Expressway Corporation test road and is subjected to a constant moving dual tire wheel load of APT at three different temperatures: 30, 40, $50^{\circ}C$. The moving wheel is applied at different loading courses within a 75cm wide wheel path to account for traffic wandering. Also, the effect of wandering on permanent deformation development is investigated numerically with three wandering schemes. In this study, ABAQUS is adopted to model APT pavement section with plain stain elements and creep strain rate model is used to take into account viscoplastic stain of asphalt concrete mixtures, and elastic layer properties are back-calculated from FWD measurements. Plus, the effect of boundary condition and subgrade on FE permanent deformation predictions is investigated. A full FE model that accounted for subgrade provided more realistic rut depth predictions, indicating subgrade has contributed to surface rutting.

• Journal of Korea Water Resources Association
• /
• v.38 no.7 s.156
• /
• pp.537-544
• /
• 2005

For the proper management of high pressurized gas storage caverns, analysis of groundwater flow field and inflow quantity according to the groundwater head, gas storage pressure and water curtain head should be performed. The finite element method has been widely used for the groundwater flow analysis surrounding underground storage cavern because it can reflect the exact shape of cavern. But the various simulations according to the change of design factors such as the width of water curtain, shape of cavern etc. are not easy when elements were set up. To overcome these limitations, two dimensional groundwater flow model is established based on the boundary element method which compute the unknown variable by using only the boundary shape and condition. For the exact computation of drainage rate into cavern, the model test is performed by using the exact solution and pre-developed finite element model. The test result shows that the model could be used as an alternative to finite element model when various flow simulations are needed to determine the optimizing cavern shape and arrangement of water curtain holes and so forth.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.2
• /
• pp.343-354
• /
• 1994

The group effect which causes different downdrag distribution in individual piles within the group was investigated by using a numerical analysis and an analytical study. The interaction factors due to group spacing and total number of piles in a group were estimated by using a three dimensional non-linear finite element approach. Based on the results obtained, it is shown that the interaction factors of pile groups varies remarkably according to the group spacing, a major influencing parameter for the group effect. Also the downdrag prediction by the proposed method was compared with the other analytical methods through an example of calculations.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.10
• /
• pp.123-131
• /
• 2005

In the present study, laboratory pull-out tests with screw anchors are carried out to investigate behavior characteristics of the anchors used in foundation system of underground structures which are applied to uplifting seepage forces. Small scaled pull-out tests in sand under saturated condition and dry condition were carried out. For estimating the group effects of the anchors, the upward displacement and the pullout load varied with spacing of the anchor were observed. The test results were compared with theoretical equation for the ultimate pull-out force. Also, the result of tests can be used to the finite element analysis program, $PENTAGON^{2D}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.259-272
• /
• 2019

Steel-concrete single-leaf blast-resistant doors are protective structures consisting of a steel box and reinforced concrete slab. By the domestic blast-resistant doors, the structure is not designed efficiently because few studies have examined the effects of variables, such as the blast pressure, rebar ratio, and steel plate thickness on the structural behavior. In this study, the structural behavior of the doors was analyzed using the FE method, and the support rotation and ductility ratio used to classify the structural performance were reviewed. The results showed that the deflection changes more significantly when the plate thickness increases than when the rebar spacing is a variable. This is because the strain energy absorbed by the door is reduced considerably when the plate thickness increases, and as a result, the maximum deflection becomes smaller. According to a comparison of the calculated values of the support rotation and the ductility ratio, the structural performance of the doors could be classified based on the support rotation of one degree and ductility ratio of three. On the other hand, more explosion tests and analytical studies will be needed to classify the damage level.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.38-46
• /
• 2014

Effects of various parameters on bond property between reinforcing bar and concrete are investigated in many researchers, and various study is on going to improve the bond strength. Properties of interface between reinforcement and concrete is important role in bond property. This study analyzed the interfacial bond mechanism between deformed bar and concrete by finite element analysis (FEA) to evaluate the effect of rib shape. The FEA model in this study is simplified 2D plane stress model. The variables of analysis are selected by rib angle, rib height, rib spacing and relative rib area. From the results of analysis, reinforcing bars with rib angle $30{\sim}60^{\circ}$ showed better bond strength than the others. Bond strength ratio following to the rib height is proportionally increased up to the $0.12d_b$, but rib spacing has little effect on bond strength. The results also indicated that relative rib area can be efficiently represented the properties of deformed shape in reinforcing bars, and zigzagged rib height shape showed excellent bond strength increase.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.325-332
• /
• 2005

This paper presents a study on defects in pearlite lamella structure of high carbon steel by means of finite-element method(FEM) simulation. High carbon pearlite steel wire is characterized by its nano-sized microstructure feature of alternation ferrite and cementite. FEM simulation was performed based on a suitable FE model describing the boundary conditions and the exact material behavior. Due to the lamella structure in high carbon pearlite steel wire, material plastic behavior was taken into account on deformation of ferrite and cementite. The effects of many important parameters(reduction in area, semi-die angle, lamella spacing, cementite thickness) on wire drawing process can be predicted by DEFORM-2D. It is possible to obtain the important basic data which can be guaranteed in the ductility of high carbon steel wire by using FEM simulation.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.465-468
• /
• 2011

압축을 받는 판 구조의 경제적인 단면 보강을 위해 종방향 보강재인 U형 단면 리브를 적용하는 것이 효과적이나, 현재 국내에서는 명확한 설계지침이나 연구자료가 제시되지 못하고 있다. 따라서 U리브의 적정 크기 및 최적 간격에 대해 검토 후 이에 관한 지침이 제시될 필요성이 있다. 이에, 본 연구에서는 U리브의 단면 크기 및 강성에 따른 탄성좌굴강도 및 좌굴모드의 변화를 알아보고자 한다. 유한요소해석 프로그램인 ABAQUS를 이용하여 고유치 해석을 실시하였고, 이론값과 해석적 결과의 탄성좌굴강도를 비교하였다. 이러한 분석 결과를 토대로 향후 U리브의 최소소요강성 및 단면 선정방안을 제시하는데 기여할 수 있을 것으로 기대된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1210-1215
• /
• 2010

The probe card are test modules which are to classify the good semiconductor chips and thin film before the packaging process. In the rapid growth a technology of semiconductor, the number of pads per unit area is increasing and pad arrays are becoming irregular. Therefore, the technology of probe card needs narrow width and lots of probe tip. In this paper, the probe tip based on the MEMS(Micro Electro Mechanical System)technology was developed a new MEMS probe tip for vertical probe card applications. For the structural designs of probe tip were performed to mechanical characteristics and structural analysis using FEM(Finite Element Method). Also, the contact force of MEMS probe tip compared with FEM results and experimental results. Finally, the MEMS probe card was developed a fine pitch smaller than $50{\mu}m$.