• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.451-460
• /
• 2004

The strength of sliding plane is usually assigned on the whole sliding plane with same value in 2D limit equilibrium slope stability method. However, the potential sliding plane is divided into two or three parts which have different sliding resistances. According to the calculation results of 3D slope stability analyses using 4 types of slope cutting models, marginal sliding resistance could affect the safety of slope significantly. In this calculation two kinds of the sliding plane strengths were applied differently to the parts of bottom and margin of the model slope. The effect of marginal resistance was calculated quantitatively. In case of lower sliding resistance of the bottom, the safety factor becomes low in a margin cutting model. However, in case of higher sliding resistance of the bottom, the safety factor decreased slightly in a lower part cutting model and increased in a upper margin cutting model.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.145-152
• /
• 2021

The purpose of this study was to determine the optimal distances between pipes to minimize the pressure loss and turbulent intensity. This was accomplished by investigating the distances between sleeve-jointed pipes and the flow changes in pipes based on variations in the Reynolds (Re) number when installing adjusting pieces for the pipes. When the thickness tp of the sleeve-jointed piping was fixed at 5 mm and the pipe lengths Lp were 10, 50, 100, and 200 mm, the correlations with the velocity of the sleeve-jointed part, pressure distribution, length of the reattachment point in the recirculation area, and Re number were analyzed. The flow characteristic of the sleeve-jointed part from a laminar to a turbulent flow region was determined by setting the Re range to 200 ≤ Re ≤ 5,000. This was done by utilizing Ansys Fluent 18.1, which is a commercial program. The enlargement and contraction ratios of the sleeve-jointed part were 1.2 and 0.83, respectively, and the turbulent intensity of the sleeve downstream edge and pressure change both increased as the Re number increased while Lp remained constant. The fact that the flow on the sleeve wall surface was disturbed by tp resulted in losses in velocity energy. Therefore, the edge of the sleeve-jointed part was also effected. When Lp was 10 mm or less, the turbulent intensity of the edge part did not change significantly as the Re number increased. The reattachment point in the recirculation area did not appear at Lp of 10 mm or less and was not affected by the vortex. In the case of 3,000 ≤ Re, the reattachment length of the wall surface of the sleeve-jointed part was nearly constant as Lp increased.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.430-439
• /
• 2002

The development of reinforcing steel is required in reinforced concrete structures. The standard hooks that have been widely used for the tensile development in the beam-column joints tend to create difficulties of construction such as steel congestion as the member cross sections are becoming smaller due to the use of higher strength concrete and higher grade steel. Using the reinforcing bars with end mechanical anchoring device (headed reinforcement) provides potential economies in construction such as reduction in development lengths, simplified details, and improved responses to cyclic loadings. In this paper, the pullout strengths and behaviors of the headed reinforcement were experimentally studied. In 33 pullout tests performed using D25 deformed reinforcing bars, the test parameters were embedment depth, edge distance, head size, and the use of transverse reinforcement. The pullout strengths determined from tests closely agreed with the pullout strengths predicted using the CCD method. The pullout strengths increased with increasing embedment depths nd edge distances. The strengths tend to increase with the use of larger heads. From the experimental program where the effect of the transverse reinforcement was examined, a modification factor to the CCD was suggested to represent the effect of such reinforcement that is installed across the concrete failure plane on the pullout strengths.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.45-45
• /
• 2009

원가 측면에서 유리한 저항점용접(Resistance Spot Welding)이 차체 용접에 80%이상으로 가장 많이 적용되고 있다. 첨단고강도강(Advanced High Strength Steel)의 저항점용접성 및 용접부 특성에 미치는 공정 변수의 영향에 대한 연구결과는 많으나, 합금원소의 영향에 대해서는 전무하다. 특히, Si는 DP(Dual Phase)강에 첨가 시 균일한 마르텐사이트의 분포를 촉진하는 원소로 저항 점용접성 및 용접부 특성에 영향을 미칠 것으로 예상되며, 이에 대한 연구는 보고된바 없다. 본 연구에서는 냉연 DP강의 저항 점용접시 중요한 인자 중 하나인 너깃경과 전단인장강도에 미치는 Si함유량의 영향을 검토하였다. 사용된 강재 및 용접기는 1.2mm 두께의 Si함유량(0, 0.5, 1.0, 1.5wt%)이 다른 인장강도 780~1000MPa급 냉연 DP강과 단상 AC용접기를 사용하였다. 용접조건은 ISO 18278-2규격에 따라 가압력 4kA, 초기가압시간 40cycle, 유지시간 17cycle로 고정하고, 용접전류만 변화하여 용접을 실시하였다. 너깃경은 용접부 단면을 컷팅 후 폴리싱 하여, 광학현미경과 Image Pro plus를 이용하여 측정했으며, 인장시편규격은 JIS Z 3137를 이용하였다. Si함유량이 증가에 따라 스패터 발생 전류는 감소했고, 너깃경은 직선적으로 증가했다. Si함유량 증가에 따른 너깃경 증가 이유는 저항(R) 측정결과, Si함유량 증가에 따라 모재의 저항이 높아져, 따라서 입열량($Q=I^2Rt$)이 많아지기 때문으로 판단되었다. 인정전단강도는 Si함유량 증가에 따라 직선적으로 증가했다. 이러한 이유는 Si함유량 증가에 따라 너깃경이 증가되기 때문으로 판단되었고, 너깃경과 인장전단강도 사이에 직선적 관계(PL(kN)=$3.2N_{dia.}$-0.81, $R^2$=0.93)를 가지고 있었다. 파단양상은 Si함유량에 상관없이 5.4kA이하에서는 계면파단이 일어났고, 6.0kA이상에서는 풀 아웃 파단이 일어났다. 계면파단주원인은 용접부 가장자리에 지름이 약 $5{\mu}m$이하의 예리한 노치가 존재하여 노치응력집중과 HAZ계면 근처에 미접합부가 존재하기 때문으로 판단되었다. 6.0kA이상에서는 예리한 노치가 없었고, HAZ부가 완전히 접합되어 있기 때문에 풀 아웃 파단이 일어난 것으로 판단되었다. 따라서, Si함유량 증가에 따라 적정용접전류 구간은 감소했고, 너깃경은 직선적으로 증가했다. 또한, Si함유량 증가에 따라 인장전간강도는 증가 했으며, 너깃경과 인장전단강도 사이에 직선적 관계를 가지고 있었다. 파단 양상은 Si함유량에 상관없이 5.2kA이하에서는 계면파단이, 6.0kA이상에서는 풀 아웃 파단이 일어났다.

• Journal of the Korean earth science society
• /
• v.31 no.7
• /
• pp.749-761
• /
• 2010

A relationship between cloud-to-ground lightning and rainfall was investigated by using the two-years (2006-2007) summer lightning data and the automatic weather stations (AWSs) data of the Korea Meteorological Administration. The negative lightning occurred at the core of highly concentrated convection, which is often accompanied with heavy rains. Whereas most positive lightning occurred at the anvil cloud with low density and light rains. The rainfall intensity is strongest when the negative and positive lightning occurred concurrently, and one with lightning is much stronger than that without lightning. A portion of the positive lightning of the total lightning was less than 10% during summer seasons, and the lightning without rains was about 34%. The rain rate was strongly correlated with the negative flash rate, and the correlation coefficients varied between 0.87 and 0.94 according to the co-location radius (5-15 km) of AWSs. Most of the lightning occurred 10 minutes before and/or concurrently occurred with rains. A portion of the convective rainfalls of the total rainfalls was at least 20% when we define the rainfalls with lightning as convective. The convective rainfall was greater during August than in June and July. In general, the portion of convective rainfalls showed a maximum diurnal variation during late afternoon as in the rains and lightning.

• The Korean Journal of Zoology
• /
• v.20 no.1
• /
• pp.29-40
• /
• 1977

The authors examined fresh-water gammarid materials which were collected from streams in 20 localities of South Korea during the period from 1965 to 1977. As the results of the observation, the authors have concluded as follows: 1. These fresh-water gammarids belong to Gammarus pulex-group and are distributed widely in mountain-streams of mainland and surrounding islands of South Korea. 2. The present specimens are different from the subspecies, G. pulex koreanus Ueno, 1940 which was described originally from North Korea. In the latter, the pulmose setae of third uropod are limited only to the outer margin of both rami. The peduncle and flagellum of second antenna are fringed with a few short setae and the flagellum is provided with calceoli. In the former, both margins of inner ramus and outer margin of outer ramus of third uropod are fringed with long pulmose setae. The peduncle and flagellum of second antenna have abundant relatively long setase and the flagellum is not provided with calceoli. 3. The present specimens are different from the subspecies, G. pulex sobaegensis Ueno, 1966 which was described originally from South Korea. The latter dwells in cave, while the former dwells in mountain-stream. In the former, the arrangements of pulmose setae of third uropod and the setation of second antenna are similar to those of the latter. But they are quite different from each other in several characters such as shape of upper lip, shape of fifth article of second gnathopod and numbers of incisions on front distal margins of coxal plates 1-3. The former has spines on surface of coxal plates 1-3, but the latter has not. In females, the former has four pairs of marsupial plates, while the latter has three pairs. 4. The present materials show local variations. Therefore, they could be divided into 3 local groups. The first group (specimens from Mt. Odae and Mt. Sogeumgang) has pulmose setae on the both margins of both rami of third uropod and second article of outer ramus is relatively long. In general, this group has setae sparsely on the both rami and especially a few setae on the outer margin of outer ramus. The second group, which are widely distributed in South Korea, has pulmose setae on the both margins of inner ramus and on the outer margin of outer ramus of third uropod. In the third group (specimens from Mt. Soyo), the pulmose setation of third uropod is similar to that of the first group, but the second article of outer ramus is very small.

• Korean Journal of Ichthyology
• /
• v.17 no.1
• /
• pp.1-7
• /
• 2005

A new chub, Zacco koreanus sp. nov., is described on the basis of 104 specimens from six localities in Korea. The new species is distinguished from other Zacco species by the following characteristics: 9~10 scales above lateral line to dorsal fin origin, yellowish anterolateral side of body, no hemicircular red blotch on the upper margin of the eyes, reddish anterior margin of pectoral fin, larger orbit diameter and narrow interorbital width. The new species is widely distributed in the most streams of Korea, except the Yeongsan R., while Zacco temminckii is restricted in the Dongjin R., Yeongsan R., Seomjin R., Tamjin R. and Nakdong R. in Korea. When the two species occurred sympatrically in the same stream, Z. koreanus sp. nov. prefered mostly rapid lotic environments while Z. temminckii inhabited lentic ones. The Korean Z. temminckii was redescribed herein. A key to the Zacco species of Korea and Japan is provided.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.57-57
• /
• 2009

산업의 고도화에 따른 구조물의 사용 환경이 열악해지고 최근 에너지저감과 환경문제 개선을 위한 경화의 요구에 따라 뛰어난 내식성 및 우수한 고비강도 특성을 갖고 있는 타이타늄 및 타이타늄합금의 활용에 대한 연구가 많은 주목을 받고 있다. 이에 따라 타이타늄 신합금의 개발뿐만 아니라 기존에 개발되어 비교적 보편적으로 적용되고 있는 타이타늄 부품의 제조 및 성형기술에 대한 수요도 급증하고 있다. 특히, 기기 및 부품 제조를 위한 용접/접합기술도 매우 중요한 요소기술로 자리메김하고 있다. 타이타늄은 산소, 수소 등의 침입형 원소와의 친화력이 강한 활성이 큰 금속으로 용접시 고온에 노출되면 급격히 산화 및 취화 등의 문제를 발생한다. 따라서 타이타늄의 용접시에는 $426^{\circ}C$이상의 온도에서는 대기로부터 용접부가 차단되도록 하는 쉴딩기술이 매우 중요하다. 타이타늄의 용접은 일반적으로 아크용접, 전자빔 용접, 레이저 용접 및 확산접합 등이 적용되고 있으나 용접입열 조정이 용이하고 아크 안정성이 높고 용접부의 기계적 특성이 우수한 GTA 용접이 작업성을 고려하여 가장 많이 적용되고 있다. 본 연구에서는 미국용접학회(AWS)의 타이타늄 용접가이드를 분석 및 소개하였고, 1t 이하의 박판 CP Ti를 대상으로 GTAW 용접부 미세조직 및 기계적 특성을 분석하였다. 이때, 용접 비드폭 제어 및 펄스 용접기술을 통하여 박판 타이타늄의 최적 GTAW 공정변수 제어기술을 분석하였다.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.1
• /
• pp.54-62
• /
• 2009

Purpose : Craniospinal neurenteric (NE) cysts are rare developmental non-neoplastic cysts of the central nervous system with diverse MR imaging findings. The purpose of this study was to evaluate various MR imaging findings of intracranial and intraspinal NE cysts. Materials and Methods : We retrospectively reviewed the MR imaging findings of six NE cysts that were confirmed by pathology. We evaluated anatomic location, signal intensity, size and enhancement pattern of NE cysts. Results : Two intracranial lesions were located extra-axially in the cerebellopontine angle and quadrigeminal cisterns. Three spinal lesions were intraduralextramedullary cysts, located ventral to the spinal cord, but one thoracic lesion was an intramedullary cyst. The signal intensity of the cysts was hyperintense on T1-weighted images as compared with the cerebrospinal fluid (CSF) for two intracranial lesions and one cervical lesion. In addition, all intracranial lesions showed diffusion restriction. For the remaining three spinal lesions, the signal intensity was nearly the same as the signal intensity of the CSF as seen on both T1- and T2-weighted images. On contrast-enhanced studies, two intracranial cysts showed a small nodular enhancement and one thoracic spinal lesion showed rim enhancement. Conclusion : NE cysts have various locations, signal intensities, and possible focal nodular or rim enhancement. Therefore, NE cysts can be included in the differential diagnosis of various craniospinal cystic or tumorous cystic lesions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.8-17
• /
• 2003

The butt lap joint structures which are usually designed by the concept of slow crack growth damage tolerance, show frequently the behaviors of multiple site fatigue crack growth around the fastener hole edges due to the fretting between the two jointed parts. In this paper, experimental tests of fatigue crack growth have been performed of a bolted butt lap joint structure having an initial corner crack at the fastener hole edge, with different fretting conditions under a flight load spectrum. The obtained test results were reviewed to investigate the effects of fretting fatigue cracks on the damage tolerance crack growth life. Computations of corner crack growth were also carried out using an existed model to compare with test results.