• Journal of the Korean Institute of Gas
• /
• v.17 no.6
• /
• pp.67-72
• /
• 2013

The flash point is the lowest temperature at which there is enough concentration of flammable vapor to form an ignitable mixture with air. The flash point is a major physical property used to analyse the fire and explosion hazards of a flammable liquid solution. The flash point data for pure components are easily available in several literature. But the flash points of the flammable binary solutions appear to be scarce in the literature. The objective of this study is to measure and estimate the flash point of acetic acid-formic acid system. Cleveland open cup tester was used to measure the flash point. The experimental data were compared with the values estimated by the Raoult's law and the optimization methods based on van Laar and Wilson equations. As a result, the estmated values by optimization methods were found to be better than those based on the Raoult's law.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.16 no.4
• /
• pp.259-266
• /
• 2014

Understanding the forest fire patterns is necessary to comprehend the stability of the forest ecosystems. Thus, researchers have suggested the simulation models to mimic the forest fire spread dynamics, which enables us to predict the forest damage in the scenarios that are difficult to be experimentally tested in laboratory scale. However, many of the models have the limitation that many of them did not consider the complicated environmental factors, such as fuel types, wind, and moisture. In this study, we suggested a simple model with the factors, especially, the geomorphological structure of the forest and two types of fuel. The two fuels correspond to susceptible tree and resistant tree with different probabilities of transferring fire. The trees were randomly distributed in simulation space at densities ranging from 0.5 (low) to 1.0 (high). The susceptible tree had higher value of the probability than the resistant tree. Based on the number of burnt trees, we then carried out the sensitivity analysis to quantify how the forest fire patterns are affected by the structure and tree density. We believe that our model can be a useful tool to explore forest fire spreading patterns.

• Journal of the Korean Institute of Gas
• /
• v.15 no.5
• /
• pp.19-24
• /
• 2011

Due to the latest industrial flow comes mainly switch to high-tech industries, combustible metals as Al, Mg, Li, Zn more require to use for the aircraft, car, cell phones, electronics and others. As a result, Increasing the processing of combustible metals due to increase in amount of combustible metals giving rise dust explosions also. Most Explosions caused by combustible metal dust, occurred in air cleaning device of local exhaust ventilation to capture and store the combustible dust. Therefore, this study was conducted to present and analyze technically that deformation and rupture shape of air cleaning device structure by Finite Element Analysis(FEA) rather than a simple prediction, in case of explosion occurs in an air cleaning device.

• Fire Science and Engineering
• /
• v.20 no.3 s.63
• /
• pp.29-34
• /
• 2006

The flash and fire point are the most important combustible properties used to determine the potential for the fire and explosion hazards of flammable material. The flash point is defined as the lowest temperature at which a flammable liquid gives off sufficient vapor to form an ignitable mixture with air near its surface or within a vessel. The fire point is the temperature of the flammable liquid at which there will be flaming combustion, sustained 5 seconds in response to the pilot flame. In this study, the flash points and fire points were measured to present raw data of the flammable risk assessment for acids, using Pensky-Martens Closed Cup(C.C.) apparatus (ASTM-D93) and Tag Open-cup (O.C.) apparatus(ASTM D 1310-86). The measured fire points were compared with the estimated values based on 1.11 times stoichiometric concentration. The values calculated by the proposed equation were in good agreement with measured values.

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.108-117
• /
• 2001

A sensor array with 10 discrete sensors integrated on a substrate w3s developed for discriminating the kinds and quantities of inflammable gases, like butane, propane, methane, LPG, carbon monoxide. The sensor array consisted of 10 metal oxide semiconductor gas sensors using the nano-sized $SnO_2$ as base material and had differentiated sensitivity patterns to specific gas. The sensor array was designed with uniform thermal distribution and had also high sensitivity and good reproductivity to low gas concentration through nano-sized sensing materials with different additives. By using the sensing patterns of the sensor array at $400^{\circ}C$, we could reliably discriminate the kinds and quantities of the tested inflammable gases under the lower explosion limit through the principal component analysis(PCA).

• Clean Technology
• /
• v.5 no.1
• /
• pp.42-48
• /
• 1999

Waste tires have both sides which are contamination and reuse concern with environmental problems. In this study, tire pyrolysis was conducted to convert combustible gases using thermal plasma. Production of combustible gases was found by gas chromatography after thermal plasma pyrolysis of waste tires without oxygen. The combustible gases consist of low molecular hydrocarbons such as $CH_4$, $C_2H_2$, $C_4H_{10}$ etc. As tire feed rate increased, the composition of $CH_4$ in the gases was increased. As plasma power increased, the composition of $C_2H_2$ was increased. $C_2H_2$ and $C_4H_{10}$ were dominant and had the ratio over 70% in the gases. On the other hand the trends of pyrolysis was characterized in the thermal plasma from the results of TG analysis which shows the currents of decomposition of the char according to the temperature.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.72-77
• /
• 2009

In the recycling procedure of the refrigerator, the fire frequently breaks out. In this study, to clarify the exact cause of the fire, the components and concentration of the materials produced in the process are analysed as well as the problems in the process system, and the protective measure to prevent the fire and the explosion fundamentally is proposed. In this procedure, the preventive measures of fire by removing the combustible materials such as polyurethane and inflammable gases, by removing the ignition sources and by reducing the oxygen concentration to the minimum are proposed along with the protective measures to reduce the damage in the fire. In the crushing procedure where the fire or explosion can break out in diverse ways, the forced ventilation or exhaust system applied to the small partial ventilation facility are installed to reduce the concentration of inflammable gas mixture to lower than the inflammable limit by injecting and exhausting the air forcibly.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.1-6
• /
• 2017

The fire and explosion properties of combustible materials are necessary for the safe handling, storage, transportation and disposal. Typical combustion characteristics for process safety include auto ignition temperature(AIT). The AIT is an important index for the safe handling of combustible liquids. The AIT is the lowest temperature at which the material will spontaneously ignite. In this study, the AITs and ignition delay times of n-pentanol and p-xylene mixture were measured by using ASTM E659 apparatus. The AITs of n-pentanol and p-xylene which constituted binary system were $285^{\circ}C$ and $557^{\circ}C$, respectively. The experimental AITs and ignition delay times of n-pentanol and p-xylene mixture were a good agreement with the calculated AITs and ignition delay times by the proposed equations with a few A.A.D. (average absolute deviation). Therefore, it is possible to estimate the AITs and ignition delay times in other compositions of n-pentanol and p-xylene mixture by using the predictive equations which presented in this study.

• Journal of the Korean Institute of Gas
• /
• v.20 no.5
• /
• pp.1-8
• /
• 2016

The autoignition temperature (AIT) of a substance is the lowest temperature at which the vapor ignites spontaneously from the heat of the environment. The AIT is important index for the safe handling of flammable liquids which constitute the solvent mixtures in the process. This study measured the AITs of n-butanol+p-xylene mixture by using ASTM E659 apparatus. The AITs of n-butanol and p-xylene which constituted binary system were $340^{\circ}C$ and $557^{\circ}C$, respectively. The experimental AITs of n-butanol+p-xylene mixture were a good agreement with the calculated AITs by the proposed equations with a few A.A.D.(average absolute deviation).

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.54-54
• /
• 2011

방사 공정 최적화를 위해 칩(chip)건조를 실시하여 칩의 수분을 모두 제거한 후 실험을 진행하게 된다. 칩은 그 자체가 공정수분율(0.4%) 또는 그 이상의 수분을 함유하고 있으므로 건조하지 않고 방사하면 현저히 가수분해가 일어난다. 가수분해가 일어난다면 PET 분자량도 저하되어 고분자의 성질을 잃게 되어 방사된 섬유의 물리 화학적 성질에 중요한 영향을 받게 된다. 그러므로 가수분해를 방지하기 위하여 칩내 수분을 제거하는 건조 공정을 거치는 것이다. 개발된 나노은입자을 함유한 Ag/PET 마스터배치의 제사성 및 가연성 평가을 위한 파일럿연구를 행했다. 본 연구에서 사용한 은나노 M/B 칩(chip)의 경우 일반적으로 사용하는 PET 칩에 비하여 낮은 고유점도를 가지므로 방사성에 칩의 수분이 더욱 영향을 미칠 것이라 판단되어 건조공정에 특별한 주의을 하여 진행하였다. 마스터배치의 고유점도(IV)값의 변화에 따른 제사성 및 가연성 평가를 관찰하였다. #3 M/B 칩의 제사성이 #1 M/B 칩 대비 공정성이 개선되어 두 품종 모두 비출사가 발생하지 않았으며, M/B 제조시 분산제 유무에 따른 방사공정성의 차이는 없는 것으로 보인다. 따라서 #1 M/B 대비 공정성이 개선된 점은 M/B의 IV개선에 기인하는 것으로 판단되었다.