• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.514-520
• /
• 1993

In this paper the cure cycle of carbon fiber/phenolic resin was investigated by the Taguchi Method in an experimental design. Experiments were systematically performed using $L_{18}(2^1 \times 3_7)$ orthorgonal array table of the experimental design. In the experimental design, eight compression molding parameters (heating rate, pressing temperature, pressing rate, molding pressure, curing temperature, dwell time at curing temperature, cooling rate and degassing) were considered and the effects of the parameters on the flexural strength and the apparent porosity of carbon fiber/phenolic composites were investigated. The analysis of variance for the experimental results indicated that molding pressure and curing temperature are the most significant parmeters in the flexural strength and the apparent porosity of carbon fiber/phenolic resin composites, respectively.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.346-353
• /
• 2001

This research investigates the mixture proportioning of waste newsprint paper fiber for thin-cement product. Waste newsprint paper fibers obtained through shredded mechanically by a dry process. Waste newsprint paper fiber reinforced cement composites was manufacted by slurry-dewatering method. The waste newsprint paper fiber reinforcement conditions (fiber mass fraction, level of substitution of virgin fibers, level of fiber beating) and processing variables (pressed, unpressed) are optimized through experimental studies and statistical analyses based on factorial design of experiments and analyses of variance. The optimized recycled waste newsprint paper fiber reinforced cement composites were technically evaluated. The results are shown to possess acceptable properties and strong potentials of the recycling of waste newsprint paper of the reinforcement of thin-cement products.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.4
• /
• pp.55-67
• /
• 2019

This study analyzed the fabric and product size of the burn patient's custom compression garment and measured the pressure applied by the garment to assess whether proper pressure is being delivered for treatment. The test clothes were presented to the market by body size and commissioned with the same design. The subjects selected four people close to the average body size of men in their 20s determined by 7th Size Korea. The experiment was conducted by wearing a compression suit, performing activities and measuring changes in the pressure of the garment according to changes in posture. The fabric used for the compressive clothing was not ruptured even at 216 kPa, the elasticity recovery rate was measured between 80.5 and 94.5%. The product dimensions of the experimental clothing varied by up to 8cm from brand to brand, requiring the standardization of compression clothing. The experiment showed that four types of compression suit varied in pressure, and the pressure range, excluding the gastric arm (17.9mmHg), was between 2.5-14.1mmHg, which failed to meet the level of pressurization for treatment purposes. The clothing pressure in the chest area dropped when performing movements rather than standing still. This was interpreted to be a result of reduced the adhesion of the compression suit during operation. The peak pressure (31.68mmHg) and the lowest pressure (2.2mmHg) was noted in the scapula, indicating that no pressure was being transmitted on the vertebrae. The pressure of the garment on the right shoulder blade was elevated in a supine position. Because much time is spent laying down, it is necessary for the pattern design to accommodate for the increased clothing pressure on the shoulder blades. Standardization of the level of pressurization for burn patient's custom-made pressure suits for each stage of treatment is urgently required.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2001.03a
• /
• pp.40-60
• /
• 2001

핵변환 후 영구 처분될 가압경수로 및 중수로용 사용후핵연료에 대한 인간 생태계에 대한 영향을, 직접 처분하는 경우와 비교해 보았다 심지층 처분된 용기에 저장된 사용 후 핵연료로부터 유출된 방사성 핵종들이 공학적 방벽을 거쳐 결정질 기반암 내 균열대를 통해 지하수의 흐름을 따라 이동하면서 , 다양한 지질 및 암종을 거쳐 생태 환경으로 도달한다는 핵종 유출 시나리오 중 가장 보수적인 시나리오인 우물 시나리오에 대한 위해도를 평가하여 상대적인 환경친화성을 정량적으로 제시하였다. 현재 국내에 가속기와 미임계형 원자로를 함께 사용하는 핵변환시스템과 임계형 원자로와 같은 핵변환 시스템이 개념적인 수준에서 개발되고 있어, 이 연구를 통해 향후 핵변환시스템 연구에서 요구되는 항목들도 기술적 개선, 경제성 제고, 환경 친화성, 그리고 수용성측면에서 제시하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.276-281
• /
• 2009

장거리 용수공급 시스템에서 전력비용은 전체 운영비용의 큰 부분을 차지한다. 본 연구는 시간단위의 펌프와 배수지 시스템의 최적 운영계획을 수립하기 위해 동적계획기법에 기초한 방법론을 제시하고 있다. 해석방법은 가용 가능한 펌프의 효율적 운전과 전력요금체계, 시간대별 용수수요추이 그리고 배수지 특성과 송수관로의 제약조건 등을 고려하였다. 이를 위해 적용 가능한 시스템 운영목적과 제약조건이 제시되었고 개발된 방법은 수도권 광역상수도 양주계통의 2개 가압장과 5개 배수지를 대상으로 적용되었으며, 적용결과는 상당한 수준의 펌프운전비용을 절감할 수 있는 것으로 나타났다. 이와 같은 방법은 생애주기 비용 최소화 측면에서 실제 용수공급 시설 운영과 대규모 용수공급 체계의 설계 등에 적용이 가능하다.

• Geotechnical Engineering
• /
• v.6 no.3
• /
• pp.31-40
• /
• 1990

The soil deformation due to a pile penetration in sandy soils has been analysed in model pile penetration tests. To simulate the actual ground conditions, especially the in-situ stress levee the tests were performed in a calibration chamber where both the vertical and the horizontal stresses could be applied separately. The deformation was monitored via 5 earth pressure cells. The results, were compared with the theortical values based on the theory of cavity expansion.

• Journal of Ginseng Research
• /
• v.23 no.3 s.55
• /
• pp.164-171
• /
• 1999

Microwave-assisted extraction, which is known to rapidly extract target compounds from natural products, was monitored by response surface methodology (RSM) while extracting ginsenosides by using microwave extraction system (MES) equipped with closed vessels, and was confirmed on its extraction efficiency. On the whole, coefficients of determinations $(R^2)$ of the models on ginsenoside contents of extracts with various extraction conditions were above 0.83 (p<0.1). $Ginsenoside-Rb_2,\;-Rc,\;-Re\;and\;-Rg_1$ were maximized in $140^{\circ}C$ of extraction temperature and $50\~75\%$ range of ethanol concentration. Unknown compound peak on HPLC chromatogram observed at extraction temperature over $120^{\circ}C$, increased at the extraction temperature of $150^{\circ}C$. The extraction temperature of $ginsenoside-Rb_2$ and -Re increased from $129^{\circ}C\;to\;147^{\circ}C$ with including unknown compound, and $R^2$ of the models on ginsenoside contents of extracts increased with including unknown compound into ginsenoside $Rb_2$ and Re. Contents of unknown compound were minimized in $67.33\%$ of ethanol concentration, $99.34^{\circ}C$ of extraction temperature and 3.65 min of extraction time. Ginsenoside contents extracted by microwave system for 8 min showed a similar tendency to those of the current extraction method for 40 hrs.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.184-187
• /
• 2018

The most important factor in the prevention and treatment of cerebral infarction is to increase cerebral blood flow. Methods for increasing cerebral blood flow include drug-based methods, the surgery, invasive procedures directly inserting medical devices into the artery(NeuroFloTM) and so on. The noninvasive cerebral blood flow increasing device proposed in this paper can reduce the burden on the patient because the probability of complication is low and the treatment level can be determined according to the blood pressure state of the patient. In implementing such a noninvasive cerebral blood flow increasing device, it is important to measure the accurate mean arterial pressure for provision the appropriate level of treatment for the patient. Therefore, to remove a noise, analog and digital filters were used and algorithm for peak value detection, pump control algorithms and so on were.

• Journal of Bio-Environment Control
• /
• v.16 no.4
• /
• pp.297-302
• /
• 2007

Discharge variations of perforated hose and drip irrigation systems were examined to evaluate irrigation uniformity at different pressures and length of branch line. Evaluation using statistical uniformity indicated that button drippers performed at excellent level but drip tapes and drip hoses were a little lower level. Nominal discharge of drip irrigation systems showed at the high side within the range of regulating pressure provided by the manufacturer. It is desirable that the length of branch line for drip hose, drip tape, and button dripper should be limited to 50 m, 70 m, and 100 m, respectively. Irrigation uniformity of perforated hoses showed very low level. So it is recommended that the length of branch line for perforated hoses should be limited to $30{\sim}35m$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.325-332
• /
• 2022

The vertical take-off and vertical landing (VTVL) function is essential to carry out exploration missions on the moon or Mars. For this, the engine of the exploration vehicle must have appropriate thrust control accuracy and response time. The hybrid rocket engine (HRE) is known to have a high level of thrust control capability that can satisfy these conditions. This study aims to first verify whether the thrust control performance of the developed HRE is suitable for VTVL. To this end, an oxidizer supply system that does not use a pressurization device was adopted, aiming for a mission time of about 10 seconds. In this study, the thrust control characteristics appearing under various supply pressure decreasing conditions were identified through experiments. Appropriate tank and charging conditions were set from the experimental results. In addition, the results of previous studies and current study's test were compared to confirm whether the developed HRE had adequate control performance for VTVL, and finally, the thrust control performance was verified through altitude control simulation.