• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.129-140
• /
• 2012

Smoke toxicity is the test for the toxicity evaluation of smoke and hazardous gas, caused by combustion of building materials and finishing materials. Smoke toxicity can be evaluated by the mean incapacitation time of mice. This test result can be influenced by the health status of mice and test condition. In acute inhalation toxicity test of hazardous gas, no typical clinical findings and histopathologic abnormalities were observed. Tracheitis and bronchitis as well as acute lung inflammation around terminal bronchiole in some mouse of the highest dose group. Through this study, we established the method for inhalation toxicity test of hazardous gas as well as the SOP of inhalation toxicity test. However, in the future studies, the concentration control methods for inhalation technologies on hazardous gas will be needed to improve continuously and also further studies on other gas inhalation toxicity will be needed to conduct.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.197-201
• /
• 2004

SiO$_2$ and SiON thick films were deposited by Plasma Enhanced Chemical Vapor Deposition (PECVD) technique on silicon wafer (100) using SiH$_4$ and $N_2$O as precursor gases. In this work, the influence of rf power, and rf bias power on the optical and physical properties of SiO$_2$ and SiON thick films is presented. The refractive index decreases with increasing rf power, and rf bias power. The refractive index of the films varied from 1.4493 to 1.4952 at wavelength at 1552 nm, with increasing rf power, the nitrogen content decreases while the oxygen content increases, in a manner that the O/N ratio increases approximately linearly.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.219-220
• /
• 2009

이번 실험에서는 TiN의 건식 식각 특성을 연구하기 위해 $BCl_3/Ar/N_2$ 유도 결합플라즈마를 이용하였다. BCl3와 Ar의 가스 비율이 $BCl_3$ (5 sccm)/Ar (15 sccm)/N (4 sccm) 인 상황에서 RF power와 DC bias, 그리고 process pressure을 식각변수로 설정하였다. TiN의 식각률은 Alpha-step 500으로 측정하였고 표면의 식각 후 화학반응은 XPS로 측정하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.45-51
• /
• 2015

In order to meet the enforced emission regulations and reduce fuel consumption, various new technologies are employed in engines. The problem of NOx emissions under a lean mixture condition should be solved, because a lean-burn direct-injection engine can realize stable lean combustion with a stratified mixture, which results in improvements in fuel economy and emissions. This study investigated the effects of intake and exhaust valve timing changes on the performance and emission characteristics of a lean-burn LPG direct-injection engine. Under a partial-load operating condition without throttling, an increase in the intake valve opening led to an increase in NOx emissions due to an increase in the amount of excess air. The fuel consumption deteriorated with an increase in the exhaust valve opening due to a decrease in the expansion work and an increase in the pumping loss.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1013-1019
• /
• 2007

Amorphous silicon and silicon-nitride films were deposited using plasma-enhanced chemical vapor deposition (PECVD) method at $150^{\circ}C$. As fraction of $H_2$ in source gas was increased, characteristics of low-temperature silicon-nitride films approached those of conventional high-temperature films; the refractive index approached 1.9 and the ratio of nitrogen-hydrogen bonds to silicon-hydrogen bonds increased. And also, as fraction of $H_2$ in source gas was increased, characteristics of low-temperature silicon films approached those of conventional high-temperature films; refractive index and optical band gap approached 4.2 and 1.8 eV, and $[Si-H]/([Si-H]+[Si-H_2])$ increased. Lower RF power and process-pressure made the amorphous silicon films to be better properties. Increase of $H_2$ ratio seemed as the common factor to get reliable amorphous silicon and silicon-nitride films for thin-film-transistors (TFTs) at low temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.45-53
• /
• 2008

The burning behaviors of board for flooring materials were investigated using cone calorimetry at an incident heat flux of $50kWm^{-2}$. Seven domestic flooring materials were used to observe the burning behavior of maximum heat release rate, total heat release and average heat release rate. The experimental data indicated that the medium density fiberboard (MDF) flooring had higher release rate than the other flooring materials. Also, the mass loss of MDF flooring was higher than the other floors. When measuring the smoke production from burning, PE fiberboard flooring and PVC Plastic Resin Sheet showed higher carbon monoxide and carbon dioxide yield than the others. The average smoke release of both carbon dioxide and carbon monoxide through specific extinction area was similar. Toxic smoke measurement from flooring materials were determined by the mouse stop motion, and the results indicated that MDF flooring contains more toxic material than the other flooring materials.

• Korean Journal of Materials Research
• /
• v.7 no.10
• /
• pp.851-855
• /
• 1997

본 실험에서는 저유전율 층간절연물질로서 SiOF박막을 ECR plasma CVD를 이용하여 증착하였다. 또한 증착시에 발생시킨 플라즈마의 특성 분석을 위하여 Langmuir probe를 반응챔버에 부착하여 플라즈마 밀도, 마이크로파 전력은 700W, 기판온도는 30$0^{\circ}C$에서 행하였다. 증착된 SiOF 박막을 분석한 결과, 가스유량비(SiF$_{4}$/O$_{2}$)가 0.2에서 1.6으로 증가하였을 때 불소의 함량은 약 5.3at%에서 14.5at%로 증가하였으며, 굴절률은 1.501에서 1.391로 감소하였고 이는 불소 첨가에 의한 박막의 밀도감소에 의한 것으로 생각된다. 또한 박막의 유전상수는 가스유량비가 1.0(11.8qt.% F함유)일 때 3.14였다.

• Proceedings of the Technology Innovation Conference
• /
• 2006.02a
• /
• pp.207-225
• /
• 2006

지금까지 기업의 신기술 채택에 관한 연구는 주로 Rank, Epidemic 등으로 대표되는 개별적인 요인을 중심으로 수행되어 왔다. 하지만, 기술 채택은 복잡한 과정을 통해 이루어지기 때문에 개별 요인보다 다양한 요인들이 통합된 모형을 필요로 한다. 이를 위해 에너지관리공단의 온실가스 감축수단 조사사업의 설문조사 데이터를 이용하여, 온실가스 배출량이 가장 큰 발전산업을 중심으로 로짓, 프로빗 모형을 통해 기술 채택 요인에 따른 기술 혁신의 확산을 예측하였다. 그 결과, 기업의 측면에서 기업의 매출액, 목표회수기간, 기술의 인지 여부 등이 유의했고, 기술의 측면에서 기술의 초기비용은 유의했지만 본 연구에서 특별히 관심을 갖고 지켜봤던 이산화탄소 저감률은 유의하지 않았다. 이를 통해서 어떤 기업이 신기술을 더 빨리 채택할 것이며, 어떤 기술이 더 빨리 채택될 것인가를 예측할 수 있었다.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.1045-1048
• /
• 2010

본 연구는 LPG 충전소 등에서 운용하는 저장탱크에 대하여 퓨방법을 통하여, 기존의 지상형과 지하형의 장점과 단점을 비교 판정하여 혁신시공법으로 고객만족을 실현시키기 위함이다. 자동차 연료로서 LPG(Liquefied Petroleum Gas)의 사용은 대기오염을 줄이는데 효과적으로 사용이 빠르게 확산되고 있다. 하지만 가스사용이 늘어나면서 폭발과 화재에 의한 인명피해가 해마다 발생하고 있으며, 특히 대규모 저장시설에서의 가스사고는 사회적으로 심각한 문제를 야기하고 있다. 따라서, 본 연구는 LPG를 대량으로 취급 저장하는 시설에서 운용하는 저장탱크의 설치방법을 개선하기 위하여 아이디어 판단기법중 하나인 퓨(Pugh) 방법으로 판단하면 기존의 지상형과 지하매몰형, 지하격납형에서 안전성과 토지이용률이 우수한 지하격납저장탱크가 가장 효과적임을 알 수 있다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.2
• /
• pp.64-69
• /
• 2013

The structure of pore network of gas diffusion layers (GDLs) in PEMFCs plays a critical role in determining the transport phenomena of reaction gas as well as generated water. In addition, the interactive characteristics between water and surface of pore are no less important than the structural characteristics of pore network. In this study, porometric investigation is conducted for two kinds of GDL using method of standard porosimetry which enable to distinguish hydrophobic pores from hydrophilic pores of GDLs. The porosity of TGPH-120 decreases by 6% by adding 30 wt.% of PTFE, but the porosity of hydrophilic pores decreases by 12%. The relation of $p_c-S_{nw}$ varies with the addition of PTFE, especially at low $p_c$.