• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.5-10
• /
• 2004

본 연구는 단기통 4행정 기관의 배기단의 형상에 따른 실험과 수치해석이 소개되었다. 흡 배기 밸브가 작동하고 있고, 주요한 배기단의 변수로는 배기단 직경이 적용이 되었다. 실험결과로는 배기단의 직경에 따라 배기 압력은 많은 영향을 받았는 것으로 나타났다. 배기단의 직경이 감소하였을때, 배기압력파의 진폭과 파수가 증가되었다. 배기단의 직경이 증가 하였을 때, 배기압력파의 진폭이 감소하였다. 직경이 22mm 일 때의 소음의 주파수 분석이 16mm와 28mm 보다 진폭이 작게 나타났다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.27-33
• /
• 2001

In this study, it is observed that the distribution of combustion chamber volume affects the volumetric efficiency. The distribution ratio was adjusted by controlling combustion chamber volume of head and piston bowl one. Four cases were investigated, which are the combination of different distribution ratios and different compression ratios (9.8-10.0). A commercial SOHC 3-valve engine was modified by cutting the bottom face of the head and/or replacing the piston by the one that has different volume. The result shows that the less the head side volume, the more volumetric efficiency is achieved under the same compression ratio. It is also observed that increasing volumetric efficiency results in early knock occurrence due to increased "real" compression ratio. To consider reliability in estimating the volumetric efficiency, we examined the sensitivity of the AFR equation to possible errors in emission measurements. It is shown that the volumetric efficiency, which is calculated by measuring AFR and fuel consumption, can be controlled in 1% error. 1% error.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 2001

This study presents an self tuning regulator(STR) to improve the air-fuel ratio control of performance of gasoline engine. The STR is designed based on the nonlinear dynamic engine model, and the performance of the STR is evaluated through the simulation and experiments. The STR shows better performance than a conventional PI controller in terms of the response time and disturbance rejection. Since the STR has less calculation load than the complex nonlinear controller, this algorithm can be easily applied to on-board engine controller.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.105.2-105.2
• /
• 2012

타이타늄합금기지 복합재료(Ti-MMC)는 일반 철합금 혹은 철합금기지 복합재료에 비하여 내식성과 내마모성, 내열성, 강도 등이 우수하여, 고성능 가솔린자동차 부품 외에도 하이브리드 자동차 엔진 부품, 고온 압축기 및 터빈 휠 등 고온에서 사용되는 고속 회전품으로 응용가능성이 매우 크다. 그러나 아직까지도 타이타늄 원소재 가격이 높고 제조 공정의 어려움으로 인하여 실용화에 장애가 되고 있다. 이를 극복하기 위하여 최근에는 타이타늄기지 복합재료의 제조단가를 낮추는 동시에 기계적 성질을 개선하기 위한 다양한 연구들이 진행되고 있다. 본 연구에서는 고가의 HDH(Hydride-Dehydride) 공정에 의하여 제조된 타이타늄 분말 대신에 저가의 titanium hydride를 사용하여 반응생성 공정으로 제조단가가 낮은 복합재료를 제조하고자 하였다. 당 연구실에서 저비용합금으로 개발된 Ti-Al-Fe 계 타이타늄합금을 기지로 한 TiB 강화 복합재료를 제조하기 위하여 반응분말로 $TiB_2$를 사용하여 제조하였다. 강화상 분율에 따른 밀도변화와 제조 공정변수에 따른 소결특성과 기계적 특성 변화에 대하여 조사하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.19-27
• /
• 2001

This paper is the first of 3 companion papers which investigate axial stratification process. In-cylinder fuel behavior has been investigated in the port injected SI engine by visualization for the purpose of understanding stratification. Planar laser light sheet from an Nd:YAG laser has been illuminated through the transparent quartz cylinder of the single cylinder optical engine and the Mie scattered light has been replaced with an air-ethanol mixture to utilize atomized fuel spray for the visualization purposes. This results have been compared with steady flow concentration measurement. For no swirl port, the axial penetration depends on the fuel injection timing. The fuel tends to remain in the upper region of the cylinder far from the spark plug and the distribution is not affected by the injection timing except 90 ATDC.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.128-136
• /
• 1997

Spray characteristics of a fuel injector have an important effect upon engine power and emission. Thus this study was investigated the spray characteristics of the intermittent injection using a gasoline fuel injector. Image processing system and PDA system were utilized for visualization of a spray behavior and measurements of a droplet size and velocity, respectively. Fuel injection duration was fixed with 3ms and injection pressure was varied such as 250kPa, 300kPa, 350kPa. for a high fuel injection pressure, spray tip arrival time was fluctuated at a vigorously disintegrated cross section. Axial velocity was linear correlated with fuel droplet size in the time interval of an injected main spray at spray downstream.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.203-210
• /
• 2003

A simulation study was carried to analyze the vehicle fuel consumption on component basis. Experiments was also carried out to identify the simulation results, under FTP-75 Hot Phase driving conditions. and arbitrary driving conditions. A good quantitative agreement was obtained. Based on the simulation, fuel energy was used in pumping loss(3.7%), electric power generation(0.7%), engine friction(12.7%), engine inertia(0.7%), torque converter loss(4.6%), drivetrain friction(0.6%), road-load(9.2%), and vehicle inertia(13.4%) under FTP-75 Hot Phase driving conditions. Using simulation program, the effects of capacity factor and idle speed on fuel consumption were estimated. A increment of capacity factor of torque converter resulted in fuel consumption improvement under FTP-75 Hot Phase driving conditions. Effect of a decrement of idle speed on fuel consumption was negligible under the identical driving conditions.

• Journal of Power System Engineering
• /
• v.8 no.1
• /
• pp.13-17
• /
• 2004

In this study. an experimental study has been introduced for the various exhaust pipe geometry of 4-stroke single cylinder engine. The main experimental parameters are the variation of exhaust pipe diameters and lengths to measure the pulsating flow when the intake and exhaust valves are working. As the results of experimental test, the various exhaust geometry were influenced strongly on the exhaust pressure. As the exhaust pipe diameter was decreased, the amplitude and the number of compression wave in exhaust pressure was increased. According to decreasing pipe diameter, the number of compression wave in exhaust pressure was decreased.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.4
• /
• pp.81-88
• /
• 2008

Flow characteristics have one of the effects in the process of engine. The numerical analysis makes it possible to predict the flow fields. This paper presents characteristics of steady flow according to variation of valve lift in a gasoline engine. The numerical computations have been made to observe the pressure distribution in accordance with the variable valve lift. Characteristics of tumble flow and swirl flow according to the variable valve has also been investigated. We could find that tumble ratio and swirl ratio is different between with/without PDA valve. The steady flow test was simulated through three-dimensional analysis on intake port design for comparing with experimental data and confirming the feasibility of applying analytic method. As a result, this study shows the possibility of the usage of numerical simulation to predict the flow characteristics for gasoline engine.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.33-35
• /
• 2013

The present work is an experimental investigation on potential operating range using directly injected gasoline fuel in a single-cylinder compression ignition (CI) engine. The objectives of present study were to apply auto-ignited combustion to gasoline fuel and to evaluate potential operating range. In order to auto-ignite gasoline fuel in CI engine, the fuel direct-injection system and the intake air system were modified that a flow rate and temperature of intake air were regulated. The heat-release rate (HRR), net indicated mean effective pressure (IMEP), start of combustion (SOC), and combustion duration were derived from in-cylinder pressure data in a test engine, which has 373.33cc displacement volume and 17.8 compression ratio. The exhaust emission characteristics were obtained emission gas analyzer and smoke meter on the exhaust line system.