• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.310-310
• /
• 2012

최근 전자산업의 발달에 따른 전자제품의 소형화 및 고기능화 요구에 대응하기 위하여 저항(resistor), 커패시터(capacitor), IC (integrated circuit) 등의 수동소자를 개별 칩(discrete chip) 형태로 형성하여 기판의 표면에 실장하는 기술이 일반화되고 있다. 그러나, 수동 소자의 내장 기술은 기판의 패턴 밀도의 급격한 향상과 더불어 수동소자의 내장 공간도 협소해지는 문제점이 있다. 상기의 문제점을 해결하기 위해 개별 칩 형태의 내장형 저항체를 박막 형태의 내장 저항체를 구현하는 기술의 개발이 최근 주목을 받고 있다. 박막 저항체는 기존의 권선저항 및 후막저항과 비교하여 정밀한 온도저항계수를 가지며 이동통신에 적용시 고주파 영역(GHz)에서의 안정성과 주파수 특성이 좋다는 장점들을 가지고 있다. 박막 저항 물질로는 높은 경도와 우수한 열적 안정성을 가지고 있는 TaN (tantalum nitride)이 주로 사용되고 있다. 일반적으로, TaN 박막은 스퍼터링을 사용하며 제조되며 TaN 박막의 성질은 탄탈륨과 질소의 화학정량비, 박막의 결함 정도, 또는 공정압력 및 증착 온도, 플라즈마 파워 등과 같은 공정조건 등의 변화에 민감하게 변화하므로, TaN 박막의 다양한 연구가 더 필요한 실정이다. 본 연구에서는 반응성 마크네트론 스퍼터링을 사용하여 TaN 박막을 Si 기판 위에 증착하였고 TaN 박막의 원하는 특성을 제어할 수 있도록 질소 분압과 total gas volume을 조절하여 공정을 최적화하는 연구를 진행하였다. 또한 tensile pull-off 방법을 이용하여 TaN 박막의 부착강도를 평가하였고, 온도 사이클 및 고온고습 환경에 노출된 TaN 박막들의 열화 특성들에 대하여 연구하였다.

• The Journal of the Korea Contents Association
• /
• v.17 no.10
• /
• pp.1-8
• /
• 2017

As the recent advancement of military equipment has been accelerated, it is becoming more important to act as an inspection device that verifies the performance of equipment in real time. Most of the inspection equipments were developed on the Windows OS based system. considering development convenience and development period. However, sice the data communication between these models occurs asynchronously, there is a problem that it is difficult to guarantee real-time performance of the window-based inspection equiment. To solve these problems, we use real-time commercial solutions to guarantee the real-time performance of Windows-based inspection equipment. In this paper, we propose a method of designing and implementing the inspection equipment software based on Real-Time implanted Kernel-Multi Processor (RTiK-MP) operating in Windows environment. In addition, real-time performance data accuracy was measured through a high-speed communication tool and interlocking test to verify the performance of the inspection device based on the real-time porting kernel.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.8
• /
• pp.55-61
• /
• 2005

Mononobe-Okabe method is generally used to evaluate dynamic earth pressure for the seismic design of retaining walls. However, Mononobe-Okabe method does not consider the effects of dynamic interactions between backfill soil and walls. In this research, shaking table tests on retaining walls were performed to analyze the phase and magnitude of dynamic earth pressure. The unit weight of walls, the amplitude of input acceleration and the base friction coefficient of walls were varied to analyze the influence of these factors on the dynamic earth pressure. Test results showed that the dynamic earth pressure was 180 degrees out of phase with the wall inertia force for the low sliding velocity of the wall, whereas small peaks of the dynamic earth pressure, which are in phase with the wall inertia force, were developed for the high sliding velocity of the wall. The amplitude of dynamic earth pressure was proportional to that of wall acceleration and the unit weight of the wall. In addition, the dynamic earth forces calculated by the Mononobe-Okabe method were the upper limit of the dynamic earth pressures.

• Geophysics and Geophysical Exploration
• /
• v.25 no.4
• /
• pp.167-176
• /
• 2022

We designed a borehole deviation survey tool applicable for steel-cased holes, K-DEV, and developed a prototype for a depth of 500 m aiming to development of own equipment required to secure deep subsurface characterization technologies. K-DEV is equipped with sensors that provide digital output with verified high performance; moreover, it is also compatible with logging winch systems used in Korea. The K-DEV prototype has a nonmagnetic stainless steel housing with an outer diameter of 48.3 mm, which has been tested in the laboratory for water resistance up to 20 MPa and for durability by running into a 1-km deep borehole. We confirmed the operational stability and data repeatability of the prototype by constantly logging up and down to the depth of 600 m. A high-precision micro-electro-mechanical system (MEMS) gyroscope was used for the K-DEV prototype as the gyro sensor, which is crucial for azimuth determination in cased holes. Additionally, we devised an accurate trajectory survey algorithm by employing Unscented Kalman filtering and data fusion for optimization. The borehole test with K-DEV and a commercial logging tool produced sufficiently similar results. Furthermore, the issue of error accumulation due to drift over time of the MEMS gyro was successfully overcome by compensating with stationary measurements for the same attitude at the wellhead before and after logging, as demonstrated by the nearly identical result to the open hole. We believe that the methodology of K-DEV development and operational stability, as well as the data reliability of the prototype, were confirmed through these test applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.23-27
• /
• 2017

This paper proposes an approach to predict the reliability of high temperature heaters by identifying their primary failure modes and mechanisms in the field. Test specimens were designed to have the equivalent stress conditions with the high temperature heaters in the field in order to examine the effect of stress conditions on the solder joint failures. There failures often result from cracking due to intermetallic compound (IMC) or void formation within a solder joint. Aging tests have been performed by exposing the test specimens to a temperature of $170^{\circ}C$ in order to reproduce solder joint failures in the field. During the test, changes in IMC formation were investigated by scanning electron microscopy (SEM) on the cross-sections of the test specimens, while changes in void formation were monitored both by resistance spectroscopy and by micro-computed tomography (microCT), alternately. The test results demonstrated the void volume within the solder increased as the time at the high temperature increased. Also, the phase shift of high frequency resistance was found to have high correlation with the void volume. These results implied the failure of high temperature heaters can be non-destructively predicted based on the correlation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.489-496
• /
• 2019

This paper is a study on the evaluation of loss factor of damping treatment materials to reduce the noise and vibration for panels of railway vehicles and automobiles. In order to determine the modal parameters of damping materials, beam excitation tests were carried out using different type PVC coated aluminum and steel base beam specimens. The specimens were excited from 10 Hz to 1000 Hz frequency range using sinusoidal force, and transfer mobility data were measured by using an accelerometer. The loss factors were determined by using integrated program, based on theories of Half Power Method, Minimum Tangent Error Method, Minimum Angle Error Method and Phase Change Method, which enable to evaluate the parameters using modal circle fit and least squares error method. In the case of lower loss factor and data of linear characteristics, any method could be applied for evaluation of parameters, however the case of higher loss factor or data including non-linear characteristics, the minimum angle error method could reduce the loss factor evaluation. The obtained dynamic properties of the coating material could be used for application of Finite Element Method analyzing the noise control effects of complex structures such as carbody or under-floor boxes of rolling stock. The damping material will be very useful to control the structural noise, because the obtained modal loss factors of each mode show very good effect on over $2^{nd}$ mode frequency range.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.33 no.3
• /
• pp.197-201
• /
• 2007

Oil soluble licorice extract(licorice extract) is an officially approved cosmetic component as a whitening ingredient in Korea. The durability of licorice, during which the whitening effect can be maintained in optimum condition, must be accurately defined. Since the cosmetics durability under real condition is relatively longer than its development time. It is needed to predict the real durability interval from the experimental measurement under simulated operating conditions. We analyzed the relationship between the licorice lifetime and the high temperature condition by using Arrhenius equation. We have established the constant stress test with temperature of $50^{\circ}C$, $55^{\circ}C$, and $60^{\circ}C$ condition, within which no formulation change of licorice products is expected for the accelerated stress test. In this paper, the lifetime of licorice in cosmetics was defined as time period for its 10% contents reduction. We observed that the lifetime of licorice is 580 h at $50^{\circ}C$, 319 h at $55^{\circ}C$ and 166 h at $60^{\circ}C$. Using the above experimental data, we obtained the equation for the relationship between the licorice lifetime and temperature as follows; log(lifetime)=-35.0243 + 1.15322$\times$(11604.83/temperature). From this equation, the lifetime of licorice at $25^{\circ}C$ can be estimated as 26 months. The estimated result was verified by measuring full lifetime of licorice. In fact, there was no significant difference between the estimated lifetime and real measurement within 95 % significance level. This study can be applied to other useful cosmetic components for the fast estimation of the exact durability.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.5
• /
• pp.487-496
• /
• 2010

The structural damping ratios for seismic design of nuclear power plant structures are specified in Regulatory guide 1.61 of the United States NRC for RC structures of 4%(OBE) and 7%(SSE), and for steel structures of 3%(OBE) and 4%(SSE), but not for steel-plate concrete (SC) structures that have been developed recently. The objective of this study is to investigate the damping ratios of SC structures by identifying the relative differences in the damping ratios between RC and SC structures. An experimental study was performed on four specimens, RC-S, RC-M, SC-S and SC-M, where S stands for shear-governed and M for moment-governed. The conducted method was free vibration testing by rupturing a brittle steel plate that linked the actuator and the mass center. The test results were analyzed to determine fundamental frequencies and damping ratios at various load levels. By examining the relative differences in damping ratios of four specimens, it is proposed for SC structures to use the same damping ratio of 4% as RC one at OBE, but 1% less damping ratio than RC one resulting in 6% at SSE.

• Journal of Astronomy and Space Sciences
• /
• v.22 no.4
• /
• pp.463-472
• /
• 2005

In this paper, the dynamic model development for interplanetary navigation has been discussed. The Cowell method for special perturbation theories was employed to develop an interplanetary trajectory propagator including the perturbations due to geopotential, the Earth's dynamic polar motion, the gravity of the Sun, the Moon and the other planets in the solar system, the relativistic effect of the Sun, solar radiation pressure, and atmospheric drag. The equations of motion in dynamic model were numerically integrated using Adams-Cowell 11th order predictor-corrector method. To compare the influences of each perturbation, trajectory propagation was performed using initial transfer orbit elements of the Mars Express mission launched in 2003, because it can be the criterion to choose proper perturbation models for navigation upon required accuracy. To investigate the performance of dynamic model developed, it was tested whether the spacecraft can reach the Mars. The interplanetary navigation tool developed in this study demonstrated the spacecraft entering the Mars SOI(Sphere of Influence) and its velocity .elative to the Mars was less than the escape velocity of the Mars, hence, the spacecraft can arrive at the target planet. The obtained results were also verified by using the AGI Satellite Tool Kit. It is concluded that the developed program is suitable for supporting interplanetary spacecraft mission for a future Korean Mars mission.

• Proceedings of the KOR-KST Conference
• /
• 1998.10b
• /
• pp.295-295
• /
• 1998

고속도로에서 교통류의 특성에 파악하여 교통류의 특성을 파악하여 동적행태로 교통상황을 분석하고 효과적인 제어전략, 시뮬레이션, 그리고 기하구조 개선등의 효율적이고 실용적인 적용을 위해서는 교통류의 정확한 모사가 필요하다. 시공간으로 표현되는 상태방정식을 포함하는 거시적 시뮬레이션 모델에 사용되는 연속류 모델은 이러한 교통류 특성을 모사하는데 적절하다. Lighthill과 Whitham(1955), Richard(1956)에 의해 일계도함수의 형태를 가지는 단순모델이 제시된 이후 모델의 결점을 보완하기 위해 많은 고계도 모델이 제시되었지만 고계도 모델이 가진 이론적인 결점에 대해서는 여러 연구들이 제시되어 있다. 또한 고계도 모델은 운동량 방정식의 유도, 정산, 구현의 어려움으로 널리 사용되기 힘들다는 단점을 가지고 있다. 만일 적절히 구현할 수 있다면 적용이 간단한 단순모델로도 보다 정확한 교통류 상황 모사가 가능하다. Ansorge는 혼잡교통류상황을 보다 정확하게 모사하기 위해 단순모델에 엔트로피 조건을 결합시킨 모델을 제시했다. Bui는 이 제안된 모델이 적절한 시뮬레이션 결과를 나타낸다는 것을 밝혔다. 그러나 이 모델은 차량의 재가속이 이루어지는 교통상황-stop-start wave의 경우 비현실적인 값을 가진다. 엔트로피조건에 의해 구해진 해는 실제보다 과다한 교통량을 추정하게 되는데 이런 결과는 위와 같은 교통상황에서 중요한 요소로 작용하는 가속효과가 무시되고 있기 때문이다. 따라서 본 연구에서는 stop-start wave 조건에서 가속도에 경계치를 부여하여 교통류율을 상한경계조건을 제시함으로써 교통상황에 맞는 교통류율을 산정하는 방법에 대해 제안하고자 한다.환승이라는 특정대안변수(Specific alternative variable)를 첨가하여 그것이 수단선택에 미치는 영향을 분석한다. 또한, 대중교통의 속성을 가지고 있는 지하철과 버스를 하나의 대안으로 묶어서 효용함수를 구한 다음 다시 승용차, 택시, 대중교통을 독립된 대안으로 두고 모형을 정립하는 NESTED LOGIT모형으로 파라메타를 추정하여 대중교통의 효용에 관해 분석·비교하였다. 본 논문에 이용된 자료는 공항을 이용하는 이용객들을 대상으로 직접 설문·면접조사한 자료이며 대상 교통수단은 승용차, 택시, 지하철, 버스로 설정하였다. 결과 적응형 알고리즘이 개개인의 최단시간 경로를 제공하는 사용자 평형 경로안내전략에 비해 교통혼잡도와 정체시간의 체류정도에 따라 3%에서 10%까지 전체통행시간을 절약할 수 있다는 결론을 얻었다.출발참, 구성대외개방선면축심, 실현국제항선적함접화국내항반적전항, 형성다축심복사식항선망; 가강기장건설, 개피포동제이국제기장건설, 괄응포동개발경제발전적수요. 부화개시일은 각 5월 26일과 5월 22일이었다. 11. 6월 중순에 애벌레를 대상으로 처리한 Phenthoate EC가 96.38%의 방제가로 약효가 가장 우수하였고 3월중순 및 4월중순 월동후 암컷을 대상으로 처리한 Machine oil, Phenthoate EC 및 Trichlorfon WP는 비교적 약효가 낮았다.>$^{\circ}$E/$\leq$30$^{\circ}$NW 단열군이 연구지역 내에서 지하수 유동성이 가장 높은 단열군으로 추정된다. 이러한 사실은 3개 시추공을 대상으로 실시한 시추공 내 물리검층과 정압주입시험에서도 확인된다.. It was result