• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.2
• /
• pp.55-64
• /
• 1984

Presented is a nonlinear constitutive model for progressive tensile fracturing of concrete. The model is incremental, path-dependent, and tensorialy invariant. The total strain tensor is assumed to be a sum of a purely elastic component and an inelastic component. The material is considered to contain weak planes of all directions which characterize the planes of the microcracks. A one-to-one functional dependence is assumed between the normal stress and the normal strain across each of the weak planes. The tangential stiffness of concrete is then derived form the principle of virtual work. The present theory can be applied to loading histories which are nonproportional or during which the principal directions rotate. Good agreement with the available direct tensile test data which cover strain-softening is demonstrated.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.119-127
• /
• 1999

The objective of this study is to simulate the fracture behavior of composite structure bonded with more than 2 different cementitious materials. For this, concrete and cement were stacked and bonded in a direction perpendicular to loading and specimens were tested. Each constituent material of concrete and cement was fabricated independently also, and three point bending and indirect tensile tests were carried out for the acquisition of measured values applicable to the proposed model. As a result of comparing theoretical results and experimental ones, it was found that the proposed model derived from fictitious crack theory can be used to predict the fracture behavior of composite structures on the vases of well agreement with experimental results. It was also noted that the degree of improvement of fracture energies and strengths is greatly dependent on the stacking sequence of layers composing of a composite structure. Thus, it can be concluded that brittleness or ductility of a composite structure can be accomplished by a proper arrangement of layers on one's purpose throughout the proposed analysis.

• Geophysics and Geophysical Exploration
• /
• v.19 no.1
• /
• pp.1-10
• /
• 2016

The hypocenter distribution of microseismic events generated by hydraulic fracturing for shale gas development provides essential information for understanding characteristics of fracture network. In this study, we evaluate how inaccurate velocity models influence the inversion results of two widely used location programs, hypoellipse and hypoDD, which are developed based on an iterative linear inversion. We assume that 98 stations are densely located inside the circle with a radius of 4 km and 5 artificial hypocenter sets (S0 ~ S4) are located from the center of the network to the south with 1 km interval. Each hypocenter set contains 25 events placed on the plane. To quantify accuracies of the inversion results, we defined 6 parameters: difference between average hypocenters of assumed and inverted locations, $d_1$; ratio of assumed and inverted areas estimated by hypocenters, r; difference between dip of the reference plane and the best fitting plane for determined hypocenters, ${\theta}$; difference between strike of the reference plane and the best fitting plane for determined hypocenters, ${\phi}$; root-mean-square distance between hypocenters and the best fitting plane, $d_2$; root-mean-square error in horizontal direction on the best fitting plane, $d_3$. Synthetic travel times are calculated for the reference model having 1D layered structure and the inaccurate velocity model for the inversion is constructed by using normal distribution with standard deviations of 0.1, 0.2, and 0.3 km/s, respectively, with respect to the reference model. The parameters $d_1$, r, ${\theta}$, and $d_2$ show positive correlation with the level of velocity perturbations, but the others are not sensitive to the perturbations except S4, which is located at the outer boundary of the network. In cases of S0, S1, S2, and S3, hypoellipse and hypoDD provide similar results for $d_1$. However, for other parameters, hypoDD shows much better results and errors of locations can be reduced by about several meters regardless of the level of perturbations. In light of the purpose to understand the characteristics of hydraulic fracturing, $1{\sigma}$ error of velocity structure should be under 0.2 km/s in hypoellipse and 0.3 km/s in hypoDD.

• Tunnel and Underground Space
• /
• v.18 no.1
• /
• pp.44-57
• /
• 2008

In this study, a 2D finite-element analysis, using the SEEP/W program, was carried out to estimate the amount of groundwater flawing into a tunnel, as well as the groundwater tables around wetland areas during and after a tunnel excavation through rock mass. Four sites along the Wonhyo-tunnel in Cheonseong Mountain (Gyeongnam, Korea) were analysed, where the model damain of the tunnel included both wetland and fault zone. The anisotropy of the hydraulic conductivities of the rock mass was calculated using the DFN model, and then used as an input parameter for the cantinuum model. Parametric study on the influencing factors was perofrmed to minimize uncertainties in the hydraulic properties. Moreover, the volumetric water content and hydraulic conductivity functions were applied ta the model to reflect the ability of a medium ta store and transport water under both saturated and unsaturated conditions. The conductivity of fault zone was assumed ta be $10^{-5}m/sec\;or\;10^{-6}m/sec$ and the conductivity of grouting zone was assumed as 1/10, 1/50 or 1/100 of the conductivity of rock mass. Totally $6{\sim}8$ cases of transient flow simulation were peformed at each site. The hydraulic conductivities of fault zone showed a significant influence on groundwater inflow when the fault zone crossed the tunnel. Also, groundwater table around wetland maintained in case that the hydraulic conductivity of grouting zone was reduced ta be less than 1/50 of the hydraulic conductivity of rock mass.

• Economic and Environmental Geology
• /
• v.29 no.4
• /
• pp.421-428
• /
• 1996

The occurrence, optical property, chemical composition, crystal structure and formation environments of the phillipsite within deep-sea manganese nodules were systematically investigated in this study. Phillipsite in manganese nodules occurs in nucleus of nodules along with consolidated bottom sediments, weathered volcanic debris, and interstitial grains in the each layer of manganese encrusts. Phillipsite is predominantly pseudomorphs of volcanic shards, and occurs as white to pale yellow in color lath-shaped and equant crystals. These show aggregations of prismatic, blocky, and bladed of 2 to $20{\mu}m$ long, and 2 to $5{\mu}m$ thick. The simplified average chemical formula of phillipsite is $({Ca_{0.1}Mg_{0.3}Na_{1.1}K_{1.5}})_3{(Fe_{0.3}Al_{4.2}Si_{11.8})O_{32}{\cdot}10H_2O}$ with a very siliceous and alkalic. The $Si/(Al+Fe^{+3})$ ratio is 2.37 to 2.78 and alkalis greatly exceed the divalent exchangeable cations, and Na/K ratio is 0.59 to 0.81. The phillipsite is monoclinic ($P2_l/m$) with the unit-cell parameters, $a=10.005{\AA}$, $b=14.129{\AA}$, $c=8.686{\AA}$, ${\beta}=124.35^{\circ}$, and $V=1013.6{\AA}^3$. Phillipsites in manganese nodules formed apparently authigenically at a temperature less than $10^{\circ}C$, and they crystallized at a pressure of less than 0.7 kb, and pH of about 8 in deep-sea environments.

• Nuclear Engineering and Technology
• /
• v.20 no.2
• /
• pp.88-104
• /
• 1988

The FUel Rod Analysis(FURA) code is developed using two-dimensional finite element methods for axisymmetric and plane stress analysis of fuel rod. It predicts the thermal and mechanical behavior of fuel rod during normal and load follow operations. To evaluate the exact temperature distribution and the inner gas pressure, the radial deformation of pellet and clad, the fission gas release are considered over the full-length of fuel rod. The thermal element equation is derived using Galerkin's techniques. The displacement element equation is derived using the principle of virtual works. The mechanical analysis can accommodate various components of strain: elastic, plastic, creep and thermal strain as well as strain due to swelling, relocation and densification. The 4-node quadratic isoparametric elements are adopted, and the geometric model is confined to a half-pellet-height region with the assumption that pellet-pellet interaction is symmetrical. The pellet cracking and crack healing, pellet-cladding interaction are modelled. The Newton-Raphson iteration with an implicit algorithm is applied to perform the analysis of non-linear material behavior accurately and stably. The pellet and cladding model has been compared with both analytical solutions and experimental results. The observed and predicted results are in good agreement. The general behavior of fuel rod is calculated by axisymmetric system and the cladding behavior against radial crack is used by plane stress system. The sensitivity of strain aging of PWR fuel cladding tube due to load following is evaluated in terms of linear power, load cycle frequency and amplitude.

• Korean Journal of Legislative Studies
• /
• v.24 no.1
• /
• pp.67-101
• /
• 2018

The purpose of this study is to examine the significant factors having an effect on voting behavior of legislators in the FTA ratification votes of the 18th and 19th National Assembly. The previous studies show that the ideology and party affiliation of lawmakers are the most important factors influencing voting decisions of legislators. The study investigates whether these factors plays a significant role in voting on the FTA ratification. Statistical results show three important findings. First of all, we expected that the influence of the party variable be the most important factor due to the strong discipline of the Korean party. However, the results show that the constituency-interest variable is the most influential factor in the all analyses. Likewise, the results show that the influence of ideology variables on voting behaviors is very strong even though its impact is different by cases and models. This indicates that in the analysis of the voting behaviors of legislators, it is necessary to examine the effect of ideological variables in depth and in various ways. In addition, the results reasonably suggest that the party variable be consistently important even though its statistical significance is not shown in some models. Because the study analyzes the voting on the free trade agreement(FTA) bill, the results may not be commonly applicable to other voting behavior of legislator. Likewise, there is a limit to discussing the general characteristics of lawmakers based on the analysis on the 5 FTA ratifications. Nevertheless, the finding of the study is very significant. This is because it comprehensively analyzed the factors having an influence on the voting behavior of the legislators on FTA ratifications submitted to the National Assembly steadily since the 16th National Assembly. In addition, the study is very meaningful because it analyzed the ideological variables of the legislators in various perspectives considering that it is not easy in measuring the ideology of the lawmakers.