• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.73-80
• /
• 2005

In general, the performance of movable nozzle used for thrust vector control in solid rocket motor is estimated on the basis of the effective pivot of nozzle. However, it is nearly impossible to define the exact effective pivot by the mathematical model or experimental technique owing to pivot dynamics. In this paper, pivot dynamic properties were investigated by ADAMS simulation technique and trajectory of the exact effective pivot was modelled by the artificial neural network. Comparison of the proposed method was made with the virtual movable nozzle (computer simulation) to verify the method, and showed good agreement. Therefore, the proposed method will be applicable to predict the effective pivot of movable nozzle during bench or ground test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.1
• /
• pp.85-92
• /
• 2005

The motion of flexseal bearing for movable nozzle has inherent nonlinear characteristics due to floating rotational center and compression by combustion pressure of solid motor. To perform precise attitude control in spite of these characteristics, the TVC actuation system requires counter potentiometer as an extra position feedback sensor of movable nozzle to form a compensated control loop. The prototype TVC actuation system, test equipments and compensated controller are newly designed, manufactured and tested in consideration of counter potentiometer. On the basis of integration test, the inherent characteristics of movable nozzle and control characteristics of its TVC actuation system are analyzed and summarized in this paper.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.4
• /
• pp.30-35
• /
• 2009

Effective-pivot effects on the thrust vector control performance of the flexible seal nozzle to be used to control the flight direction of missile were investigated by computer simulation. $2^3$-Design of experiment technique was applied and ADMAS was used for the surrogate technique. As a result, radial pivot position had more influence upon the nozzle actuating performance than axial pivot position. Connecting method of actuator was also important factor in determining effective-pivot effects on the thrust vector control performance of the flexible seal nozzle.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.253-258
• /
• 1996

원자로의 가동 중지 중이나 재장전시 원자로가 설치되어 있는 수조의 냉각수가 증기발생기 안으로 유입되는 것을 막는 장비로써 노즐댐을 사용한다. 현재의 노즐댐은 알루미늄 재질로 그 무게가 무거워 노즐댐 작업자가 취급하기 어렵다. 이 노즐댐의 경량화와 동시에 구조적 강도를 증가시키기 위해서 비강성이 높은 탄소섬유 강화 복합재료와 굽힘 강성 및 전단강성을 증가시키기 위하여 벌집구조(honeycomb)의 알루미늄을 사용하여 KAERI 노즐댐-II를 설계하였다. 노즐댐에 발생하는 응력 해석을 통하여 중앙판과 측면판의 변위가 충분히 작은 값을 가지면서 파괴지수도 충분히 작은 값이 되는 탄소섬유의 적층각도를 구하였으며, 중앙판은 ［$\pm$15］로 적층하고 측면판은 ［$\pm$45 ］로 적층 하였다. 그리고 각 판의 최대 파괴지수는 중앙판의 경우 0.32, 측면판의 경우 0.27 이었고 최대변위는 각각 3.1mm, 2.7mm로 노즐댐을 사용할 때 예상되는 하중에 대하여 노즐댐의 구조적 건전성을 입증하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.122-128
• /
• 2004

• Journal of Animal Environmental Science
• /
• v.18 no.3
• /
• pp.207-220
• /
• 2012

There are around 7,500 manure tanks to treat the manures from pigs in Korea. In the tank, there are too much sediments deposited on the base and wall, which causes low efficiency of stock capacity and manure fermentation. In order to minimize sediments and to ferment manure effectively, we developed a 2-fluid jet mixer for mixing sediments in liquid livestock manure tank. For developing the prototype, we tested a factorial experimental system with various nozzles, and simulated CFD models with two kinds of nozzle arrangement. From the results of factorial experiment and CFD simulation, we concluded the dia. ratio of primary : secondary nozzle should be 1:2 and the nozzles should be arranged at the same distances toward to the circumferential direction. With this results, we manufactured a 2-fluid jet mixer which is consists of four 2-phase nozzles, centrifugal slurry pump and root's type air blower. And, we carried out the performance test of the prototype in the round shaped liquid manure tank in the farm. The performance test results showed that the uniformity of TS (Total Solid) and VS (Volatile Solid) was raised from 21.3 g/L, 13.3 g/L In steady state to TS and VS to 23.0 g/L, 14.1 g/L in the mixing operation. Therefore, we could conclude that the prototype of 2-fluid mixer could make the solid material which could be sediments in the tank not to be deposited in the tank and to be contacted to air bubbles which could enhance the efficiency of the fermentation of livestock manure.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.6 no.2
• /
• pp.9-15
• /
• 2010

US NRC issued rulemaking of 10CFR50.55a to perform the Perservice and Inservice inspection for Reactor Vessel Head Penetration Nozzle of US Nuclaer plant. The rulemaking was required the EPRI Demonstration to verify the NDE technique performing special Ultrasonic examination. In order to meet this requirement, the UT and ECT procedures was demonstrated and the NDE personnel were qualified by EPRI. In this paper, the NDE technique and analysis method are described the Preservice inspection for the Palo Verde #1/2/3 Replacement Reactor Vessel Head Penetration Nozzle using the qualified procedures and personnel.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.327-335
• /
• 1995

The normal shutdown and maintenance period of a nuclear power plant can be remarkably shortened when the examination and maintenance works in steam generator tubes are simultaneously carried out with refueling job. There are nozzle dams to Hock the coolant How from reactor to steam generator. Workers are reluctant to install nozzle dam because of the high radiation exposure and the limited working space in steam generator. Moreover, the heavy weight of present nozzle dam makes it installation and removal works much difficult. In this paper, a lighter KAERI nozzle dam with increased flexural rigidity-to-weight was designed and manufactured by changing the structure design of the present nozzle dam and by selecting new material, carbon fiber-reinforced plastic.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1159-1168
• /
• 2013

In pressurized water nuclear reactors (PWRs), the reactor pressure vessel (RPV) upper head contains penetration nozzles that use a control rod drive mechanism (CRDM). The penetration nozzle uses J-groove weld geometry. Recently, the occurrence of cracking in alloy 600 CRDM penetration nozzle has increased. This is attributable to primary water stress corrosion cracking (PWSCC). PWSCC is known to be susceptible to the welding residual stress and operational stress. Generally, the tensile residual stress is the main factor contributing to crack growth. Therefore, this study investigates the effect on weld residual stress through different analysis methods for normal operating conditions using finite element analysis. In addition, this study also considers the effect of repeated normal operating condition cycles on the weld residual stress. Based on the analysis result, this paper presents a normal operating condition analysis method.

• Solar Energy
• /
• v.11 no.3
• /
• pp.62-73
• /
• 1991

The purpose of the present work is to investigate the atomization characteristics and to find the available working conditions of given nozzles. Experimental investigations were carried out with the nozzles, "Delavan" and "Hago"(pressure atomizing simplex 1.25GPH), with $60^{\circ}$ and $80^{\circ}$ spray angles also at various nozzle pressures. In the present work, Sauter mean-diameter was utilized to describe the quality of the atomization. All sample droplets were microphotographed with high-contrust film at 50X magnification and analyzed by Nukiyama-Tanazawa distribution function. The $80^{\circ}$ spray angle gives better atomization function than $60^{\circ}$ spray angle, and available working conditions were set at approximately $8kg/cm^2$ nozzle pressure.