• Journal of Food Hygiene and Safety
• /
• v.13 no.4
• /
• pp.425-429
• /
• 1998

Three pork fabrication processing were examined for isolation and serotyping of Listeria monocytogenes. Three hundred thirty samples were collected from gloves, knife sharpeners, knives, cutting boards, conveyer belts, skinning machines, working room air, pig carcasses, and cut meat. Among the 234 samples taken from processing environment, the isolation rates of Listeria monocytogenes and other Listeria spp. were 17.5%, 34.2% respectively. Isolation rates of Listeria monocytogenes from different specimens during processing were 20.8% in gloves, 21.3% in knife sharpeners, 14.6% in knives, 20.8% in cutting boards, 28.6% in conveyer belts, 16.7% in skinnig machines. Listeria monocytogenes and other Listeria spp. were not detected in working room air. Isolation rate of Listeria monocytogenes 14.6% in pork was increased compared to that of 8.5% in pig carcasses (p<0.05). The serovars of 41 isolates from processing environment were 4b 36.6%, 1/2a 24.4%, 4ab 17.0%, 4a 4.9%, 1/2c 2.4%, and 4c 2.4%. The serovars of 4b, 1/2a, 4ab were detected from carcassess and cut meats.

• Composites Research
• /
• v.28 no.5
• /
• pp.254-259
• /
• 2015

Carbon fiber/aluminum (CF/Al) composites were successfully fabricated without pressure casting using wettability modification of carbon fiber. The wettability of liquid aluminum on carbon fibers was enhanced through electroless plating of copper on carbon fibers. Liquid aluminum was well infiltrated into carbon fiber bundles with Cu coating layer due to low wetting angle, and a lot of pores that existed in CF/Al composite without Cu coating on CF were greatly removed. However, a few tiny pores existed in carbon fiber bundles, which is due to not bad wettability between CF and Al but shrinkage cavity that was generated during cooling of CF/Al composite. The tiny pores could be effectively removed by a subsequent rolling.

• Journal of Sensor Science and Technology
• /
• v.7 no.1
• /
• pp.61-66
• /
• 1998

High quality c-axis oriented $YBa_{2}Cu_{3}O_{7}$ films were prepared using the pulsed laser deposition on $SrTiO_{3}$(100) substrate. The atomically smooth $SrTiO_{3}$surface with terraces one unit cell in height could be obtained by a high temperature annealing. $YBa_{2}Cu_{3}O_{7}$ thin films deposited on the substrates exhibited layer-by-layer growth with a c-axis unit cell height. $YBa_{2}Cu_{3}O_{7}$ thin films thus prepared showed critical temperature ${\ge}90$ K with transition width ${\le}0.6$ K, room temperature resistivity of ${\sim}300{\mu}{\Omega}cm$, and critical current density ${\sim}4.6{\times}10^{6}A/cm^{2}$ at 77 K.

• Tribology and Lubricants
• /
• v.33 no.6
• /
• pp.288-295
• /
• 2017

In order to improve the efficiency and reliability of the machine, the friction should be minimized. The most widely used method to minimize friction is to maintain the fluid lubrication state. However, we can reduce friction only up to a certain limit because of viscosity. As a result of several recent studies, surface texturing has significantly reduced the friction in highly sliding machine elements, such as mechanical seals and thrust bearings. Thus far, theoretical studies have mainly focused on isothermal/iso-viscous conditions and have not taken into account the heat generation, caused by high viscous shear, and the temperature conditions on the bearing surface. In this study, we investigate the effect of dimple depth and film-temperature boundary conditions on the thermohydrodynamic (THD) lubrication of textured parallel slider bearings. We analyzed the continuity equation, the Navier-Stokes equation, the energy equation, and the temperature-viscosity and temperature-density relations using a computational fluid dynamics (CFD) code, FLUENT. We compare the temperature and pressure distributions at various dimple depths. The increase in oil temperature caused by viscous shear was higher in the dimple than in the bearing outlet because of the action of the strong vortex generated in the dimple. The lubrication characteristics significantly change with variations in the dimple depths and film-temperature boundary conditions. We can use the current results as basic data for optimum surface texturing; however, further studies are required for various temperature boundary conditions.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.116-116
• /
• 2009

마그네슘 합금은 구조용으로 사용 가능한 금속 재료 중 가장 가벼운 소재이며, 동시에 비강도 및 비강성과 같은 기계적 특성이 우수하여 알루미늄 합금의 뒤를 이을 차세대 경량 재료로써 주목을 받고 있다. 더욱이 석유자원의 대부분을 소비하고 있는 운송기기 분야에서는 경량화를 통한 연비향상과 배출가스 저감이 가장 큰 과제이며, 이 문제를 해결하기 위한 노력의 일환으로 최경량 소재인 마그네슘 합금의 사용량은 더욱 증가할 것으로 기대된다. 한편 기존의 마그네슘 합금 관련 연구는 새로운 합금의 개발에 치우쳐 있었으며, 상대적으로 이들 합금을 활용하기 위한 가공기술, 특히 용접에 대한 연구는 아직까지 많이 부족한 실정이다. 이는 철강재와 비교하여 마그네슘 합금의 고유물성이 용접의 관점에서는 상당히 열악하기 때문으로, 마그네슘은 융점 및 비점은 낮은 반면, 증기압과 열전도율은 높고 표면장력 및 점성은 낮은 특성을 가지고 있다. 그러므로 타 공법에 비해 상대적으로 입열이 적고 고속용접이 가능한 레이저의 적용이 최적으로 판단된다. 따라서 본 연구에서는 Nd:YAG 레이저를 사용하여 압연판재로 상용화되어 있는 AZ31B 마그네슘 합금의 맞대기 용접성을 조사하였으며, 용접부의 미세조직과 용접조건에 따른 용접부의 기계적 특성을 비교 및 검토하였다. 용접부의 기계적 특성은 인장 및 경도시험을 통해 평가하였다. 그 결과 레이저 출력 1.2kW를 적용한 경우에 안정적인 강도를 얻을 수 있었으며 레이저 출력 1.5kW, 용접속도 80mm/sec의 조건에서 모재 인장강도 대비 103% 그리고 연신율 대비 47.1%의 최적의 결과가 얻어졌다. 또한 용접부의 경도는 모재와 동등하거나 다소 높은 수준이었다. 이는 용접시 용접부내 잔류하는 알루미늄에 의한 고용 강화 효과와 금속간화합물의 석출 빈도 증가, 그리고 레이저 용접의 특징인 급열급랭 공정에 기인한 결정립 미세화의 영향 때문으로 사료된다. 한편 용접부 미세조직을 관찰한 결과, 열영향부의 존재는 두드러지지 않았으며 용융경계부에서는 주상정이, 그리고 용접부 가운데에서는 등축정이 관찰되었다.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.1
• /
• pp.1-8
• /
• 1993

In this paper, the surface roughness influenced by Sm45C hardness in high frequency induction hardening and mechanical characteristics for the changed Hv 598 part and the unchanged hardness Hv 223 part by use of cermet and ceramic cutting tools was experimentally examined. Finally, we could be had some important results by processing surface roughness on cutting conditions such as cutting speed, feed rate, depth of cut and changes of tool nose radius. The results are summarized as follows. 1. In case of the same cutting condition, the hardness of workpiece was high and acquired the best processing surface roughness when the radius of the tool nose had 0.8 mm and feed rate was 0.04 mm/rev. 2. In case of the hardness of workpiece, though the cutting speed didn't have an effect on processing surface roughness, the less feed rate and the more processing surface roughness improved. On the other hand, the low inside the hardness of workpiece, the more cutting speed and the more feed rate increase, the processing surface of roughness improved. 3. Regardless of the hardness of workpiece, the change of the cutting depth didn't have great effect on the surface roughness. 4. On cutting the high surface hardness part with cutting tools of cermet and ceramic, it can be acquired the higher processing surface roughness because it hadn't been taken effect on cutting speed, In case of the cutting process of the low inside hardness part the two cutting tools have acquired the similar processing surface roughness.

• Applied Chemistry for Engineering
• /
• v.20 no.6
• /
• pp.586-592
• /
• 2009

The preparation of structures with nanosized arrays allows mimicking many different morphologies that exist in nature. In addition, polymer is considered as a material that can be easily applicable to the fabrication of nanostructures and can effectively exhibit nanosize effects since material, synthesis and processing cost is low, and many of polymer structures are well studied. Porous alumina template prepared by anodization of aluminum among nanofabrication methods is the one of promising routes that cost-effectively provides very regularly arrayed nanostructures. In this review, we describe the fabrication of the nanotemplate and template-based polymer nanostructures and their applications.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.117-122
• /
• 2010

Recently, aspheric glass lens molding core is fabricated with tungsten carbide(WC). If molding core is fabricated with silicon carbide(SiC), SiC coating process, which must be carried out before the Diamond-Like Carbon(DLC) coating can be eliminated and thus, manufacturing time and cost can be reduced. Diamond Like Carbon(DLC) is being researched in various fields because of its high hardness, high elasticity, high durability, and chemical stability and is used extensively in several industrial fields. Especially, the DLC coating of the molding core surface used in the fabrication of a glass lens is an important technical field, which affects the improvement of the demolding performance between the lens and molding core during the molding process and the molding core lifetime. Because SiC is a material of high hardness and high brittleness, it can crack or chip during grinding. It is, however, widely used in many fields because of its superior mechanical properties. In this paper, the grinding condition for silicon carbide(SiC) was developed under the grinding condition of tungsten carbide. A silicon carbide molding core was fabricated under this grinding condition. The measurement results of the SiC molding core were as follows: PV of 0.155 ${\mu}m$(apheric surface) and 0.094 ${\mu}m$(plane surface), Ra of 5.3 nm(aspheric surface) and 5.5 nm(plane surface).

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.201-205
• /
• 2001

본 연구에서는 한지가공공정의 하나인 도침공정을 현대의 칼렌다링 공정과 비교 분석을 실시한다. 도침은 커다란 나무뭉치를 사용하여 반복적으로 여러 장이 겹쳐 진 한지를 두두림으로서 한지 표면을 평활하게 하며, 광택도를 높이는 효과를 볼 수 있다. 나무뭉치는 밑면이 평활해야만 할 것이다. 보통 한지 제조업자들은 경험 을 토대로 얼마만큼의 도침이 필요한지 결정하고 실시하곤 한다. 이러한 도침공정 에서 현대의 칼렌다링이 할 수 없는 중요한 공정이 존재한다면, 현대의 초지기에도 이러한 원리를 적용함으로써 효과적인 종이의 품질개선을 이룰 수 있는 여지가 충 분히 있다고 판단된다. 한지에 있어서 도침의 역할이 무었인지, 도침은 칼렌다링으 로 대치할 수 있는 지 둥을 비교 검토하였다. 도침공정 연구를 위하여 라이너지 한 종류, 백상지 한종류, 최근에 제조된 전통 한지 세 종류를 사용하였다. 라이너지와 백상지는 일반 제지공장에서 제조되는 방 식을 그대로 사용하여 기계 칼렌다를 통과한 샘플을 얻었으며 칼렌다를 통과하지 않은 라이너지와 백상지를 특별히 같은 지종에서 얻어서 실험을 실시하였다. 기계 칼렌다링을 하지않은 라이너지와 백상지 세 종류의 전통한지는 실험실 칼렌다를 통과시켰고, 또 각각에 도침을 실시하였다. 샘플들의 기본 물성과 처리조건을 표 1 에 정리하였다. 도침 공정에서 사용한 나무 뭉치의 무게는 약 64Kg 이며, 최대 높이 41cm 로 들어올려져 자유낙하에 의한 충격을 종이에 가하였고, 분당 충격횟수는 63회 였다. 라이너지는 도침 및 칼렌다에 의해 밀도가 서서히 증대되는 것을 볼 수 있었다 (그림 1). 도침은 칼렌다에 비해 밀도 증대에 효과적이지는 못하였다. 반면 백상 지에서는 도침이 기계 칼렌다나 실험실 칼렌다보다 현저히 크게 밀도를 증대시킴을 볼 수 있었다 (그림 2). 칼렌다는 종이를 높은 전단력과 압축력으로 변형시키는데 비해 도침은 단순히 압축 압력만을 종이에 가하는 것이 다르다고 볼 수 있는데, 라 이너지와 백상지가 같은 조건하에서 왜 이러한 큰 차이를 보이는 이유를 아직 알수 없다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1229-1235
• /
• 2011

Fatigue tests were conducted on the aluminum alloy, A7075-T6 to determine the most reliable fretting fatigue damage parameter. Specimens with grooves were used, so that either fretting fatigue crack at the pad/specimen interface or plain fatigue crack at the groove could be nucleated, depending on the pad pressure. Both the crack nucleation location and initial crack orientation were examined using optical microscopy, and the results were used to assess the reliability of the various fretting fatigue damage parameters that have been most commonly used in the literature. Finite element analysis was employed to obtain the stress and strain data of the specimen, which were needed to estimate the parameter values and the orientation of the critical plane. It was revealed that both the Fatemi.Socie and McDiarmid parameters, which assume shear-mode fatigue cracking, are the most reliable.