• Korean Journal of Materials Research
• /
• v.15 no.4
• /
• pp.240-245
• /
• 2005

An oxygen free copper was severely deformed by accumulative roll-bonding (ARB) process for improvement of its mechanical properties. Two copper sheets 1 m thick, 30 mm wide and 300 m long are first degreased and wire-brushed for sound bonding. The sheets are then stacked to each other, and roll-bonded by about $50\%$ reduction rolling without lubrication at ambient temperature. The bonded sheet is then cut to the two pieces of same dimensions and the same procedure was repeated to the sheets up to eight cycles $(\varepsilon-6.4)$. TEM observation revealed that ultrafine grains were developed after the third cycle, and their size was slightly increased at higher cycles. Tensile strength of the copper increased with the strain at low strain levels, but it hardly increased from 3 cycles $(\varepsilon>2.4)$ due to occurrence of dynamic recovery, even if the imposed strain increased.

• Journal of Ginseng Research
• /
• v.13 no.2
• /
• pp.178-182
• /
• 1989

Red ginseng products manufactured by the Korea Ginseng and Tobacco Corporation were analyzed to determine the crude saponin , total saponin and ginsenoside contentents by gravimetry, spertrometry and HPLC, respectively, to see if effective quality control of the components in the products can be achieved. Medicinal powders, powders, tablets and capsules which were made from ginseng powder showed similarity in saponin content, the ratio of PD to PT saponin, and the ginsenoside content and composition, while extract powder, extract, extract tea, extract pills and tea, which were made of ginseng extract, showed difference in saponin content, ratio of PD to PT saponin, and the content and composition of ginsengside. It is, accordingly, believed that ginseng products which are uniform in contents and saponin composition can be produced by carrying out strict quality control throughout the processes of making raw red ginseng into final products.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.627-634
• /
• 2014

Machine tool vibration is well known for reducing machining accuracy. Because vibration response of a linear structure generally depends on its transfer function if the magnitude of excitation were kept constant, this study introduces a RET(Random Excitation Test) based on FRF method to evaluate stiffness of a prototype HDMTL(Heavy-Duty Multi-Tasking Lathe) for large crankshaft of marine engine. Firstly, two force loops of the lathe and corresponding structural loops were identified:1) workpiece - spindle - head stock - main bed, 2) workpiece - tool post - carriage bed. Secondly, compliances of each structural loop were measured respectively using RET with a hydraulic exciter and then converted into stiffness. Finally, the measured stiffness was compared with that obtained previously by FEM analysis. As the result, both measured and computed stiffness were closely in agreement with each other. And the prototype HDMTL has evidently sufficient rigidity above ordinary heavy-duty lathes.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.1
• /
• pp.144-150
• /
• 2020

This paper presents a numerical study on the design of composite head geometry used for compound processing machine. In order to achieve an optimum composite head geometry and to explain the interactions between the different geometric configurations, three dimensional computational fluid dynamics and design of experiment methods have been applied. From the 2k factorial design results, the most important design variable was found and the performance of the composite head was improved compared to the reference model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1369-1375
• /
• 2006

In this work, mechanical characteristics of stainless steel diaphragm have been studied as a potential robust substrate and a diaphragm material for micromachined devices. Lamination process techniques combined with traditional micromachining processes have been adopted as suitable fabrication technologies. To illustrate these principles, capacitive pressure sensors based on a stainless steel diaphragm have been designed, fabricated and characterized. The fabrication process for stainless steel micromachined devices keeps the membrane and substrate being at the environment of 8.65MPa pressure and $175^{\circ}C$ for a half hour and then subsequently cooled to $25^{\circ}C$. Each sensor uses a stainless steel substrate, a laminated stainless steel film as a suspended movable plate and a fixed, surface micromachined back electrode of electroplated nickel. The finite element method is adopted to investigate residual stresses formed in the process. Besides, out-of-plane deflections are calculated under pressures on the diaphragm. The sensitivity of the device fabricated using these technologies is 9.03 ppm $kPa^{-1}$ with a net capacitance change of 0.14 pF over a range 0$\sim$180 kPa.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.2
• /
• pp.55-62
• /
• 1999

In order to perform a elaborate task like as assembly, manufacturing and so forth of components, tracking control on the trajectory of power coming in contact with a target as well as tracking control on the movement course trajectory of end-effector is indispensable. In this paper, to bring under robust ard accurate control of auto-equipnent systems which disturbance, parameter alteration of system, uncertainty ard so forth exist, neural network controller called dynamic neural processor(DNP) is designed. Also, the learning architecture to compute inverse kinematic coordinates transfonnations in the manirclator of auto-equipnent systems is developed ard the example that DNP can be used is explained The architocture and learning algorithm of the proposed dynamic neural network, the DNP, are described and computer simllations are provided to demonstrate the effectiveness of the proposed learning method using the DNP.he DNP.

• Journal of Food Hygiene and Safety
• /
• v.15 no.4
• /
• pp.340-343
• /
• 2000

This study was performed to investigate the contents of sulfites in 1,063 dried seaweeds in Seoul Chung-Bu market from March in 1999 to August in 2000. Sulfites of the samples were determined by Zn powder reduction method and bonnier-Williams's modified method. Two samples of 1063 (0.19%) were detected over 30ppm in SO$_2$ contents by bonnier-Williams's modified method. In samples detected over 30ppm, 2 brown algaes were 171.4ppm and 295.7ppm. By Zn powder reduction method, 54 dried seaweeds (54/1063 = 5.08%) were positive reaction (1-30ppm). These were 28 dried lavers, 27 dried brown seaweeds and 2 sea cabbages. According to results, the quality test far the dried seaweeds must be reinforced to supply safety food for the citizens.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1011-1017
• /
• 1999

Electrolytic in-process dressing grinding technique which enables application of metal bond wheels with fine superabrasives in mirror surface grinding operations has developed. It is possible to make efficient precision machining of hard and brittle material such as ceramic and hard metal by the employment of this technique. However, in order to ensure the success of performances such as efficient machining, surface finish, and surface quality, it is important to sustain the insulating layer that has sharply exposed abrasives in wheel surface. Using AE(Acoustic Emission) sensor, this paper will show whether the insulating layer sustains stably or not in real grinding time. And by comparing AErms value and surface roughness their thresholds for stable electrolytic in-process dressing grinding will be determined.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.34-41
• /
• 2004

The purpose of this paper is to look at the characteristics of surface finishing which is one of the form accuracies and to obtain the fundamental technical data from the process of machining with diamond tool through experiment and theoretical analysis. The experiments were conducted with domestic made ultra-precision machine and MCD.PCD tool, with aluminum alloyed material and brass being used for the work pieces. The goal of the size accuracy was set to 100nm. The most suitable tool nose radius and machining conditions were selected, and the variations of the surface roughness were observed using SEM method while machining the distance of up to 500km. These data were evaluated and they examined the variation of the machined surfaces while cutting up to 500km of machining distance. At the same time, the state for the wear of diamond tool nose was analyzed and carefully examined through the newest measuring device. Additionally, the characteristics of ultra-precision machining technology were studied through visual analysis.

• Journal of the Korean Society of Food Culture
• /
• v.6 no.2
• /
• pp.137-140
• /
• 1991

PALFAZE is one of ZE. ZE is One of the Chinese Sause. Especially PALFAZE is made from eight materials and used for the slices raw fish or raw meat. At first ZE was made from pickled vegitables that minced, or added vineger, some spices. But later when the garic-growing was spreaded it was changed to be made from minced garic, ginger mixed in vineger or added some spices, starch. Especially PALFAZE is made from garic, ginger, salt, vineger, mamanufactured plum, dried orange rind, boild chestnut, boiled rice.