• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.1 no.2
• /
• pp.21-30
• /
• 2003

The purpose of this study was to know the effect of aquatic-exercise on muscle atrophy which induced by steroid injection. The forty-eight Sparague-Dawley adult male rats were assigned to the 4 groups; GroupI(distilled water injection), GroupII(steroid injection), GroupIII(distilled water injection and aquatic exercise), GroupIV(steroid injection and aquatic exercise). We observed their body weight, histological change by PAS stein. The results of this study were as follows; 1. After 2 weeks, the change of weights appeared that non-steroid injection groups increase weight and steroid injection groups decreased weight hasty. after 4 weeks, weights recovered from weight before test. It was possible to explain the change of weight by type II muscle fiber increase. 2. In histological change of muscle fibers, atrophy didn't observed in test group I, because type II muscle fibers were developed well. we observed not only injury of muscle fiber and muscle atrophy but specifically grouping type I muscle fiber in test group II. normal arrangement of muscle fibers were visible in test group and type II muscle fibers increased. we could observe muscle recovery because of type II muscle fibers increase in test group IV. therefore, it was seem that type II cell was recovering through aquatic exercise.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.1 no.2
• /
• pp.61-68
• /
• 2003

The purpose of this study was to compare the application method of ultrasound on the alteration of pressure pain threshold of myofascial trigger points. We used thirty patients with mayofascial pain syndrome in upper trapezius. Participants classified according to each group in non noxious dose, noxious dose by the ultrasound. The test was measured continuously pre test, post-test by algometer. The following results were obtained; 1. Pressure pain threshold were significantly increased in non-noxious dose and noxious dose group(p<.001). 2. In noxious dose group, pressure pain threshold were more significantly increased than non-noxious dose group(p<.001). These results lead us to the conclusion that non-noxious dose and noxious dose were significantly increased pressure pain threshold of upper trapezius trigger points. Therefore, a further direction of this study will be to provide more evidence that noxious dose have more effect on pressure pain threshold of myofascial trigger points.

• Journal of Power System Engineering
• /
• v.7 no.4
• /
• pp.31-37
• /
• 2003

This paper is a study on application of warm air circulator by using the carbon heating element with particle type. The main variables are the input current and amount of carbon heating source for experimental characteristics. The experimental results are obtained as follows. As the input current and temperature are increased, the resistance of heat source is decreased about $20{\sim}25%$ by the effect of negative resistance. As the amount of heating source is small, Joule heat is large with the input current. When the amount of heating source is 300 and the input current is 15A, the value of Joule heat is about 4604.6kJ/h. The heat production efficiency of carbon heating source is larger about 10% than the sheath heater.

• The Journal of Engineering Geology
• /
• v.3 no.3
• /
• pp.267-278
• /
• 1993

Ground-water temperature is one of the parameters for observing diarges in the state of the ground-water regime in time and space, which relate to conditions for recharge as well as the influence of various natural and man-induced fadors on the regime. Because ground-water satura tes much of the rock materiats in the upper layer of the earth's csust the water temperature reflects in part the temperature of the water-bearing rocks. The mobffity and thennal capadty of groud-waters, however, serves to redistribute some of the heat within the stratosphere and to influence the developement of the geothermal regime within this sphere. The utilization of temperature data of the study area(25 points) in the solution of hydrogeologic problems requires an understanding of some of the fundamental aspects of subsurtice temperatures. These include the depth of penetration of heat waves generated of the surtace, the rate of propagation of the waves, and the geothermal gradient in the study area of Taegu.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.35-40
• /
• 2007

The new PEI(poly(epoxy-imide))-nano Silica film has been synthesized via in situ CS sol process, and the chemical bonding and microstructure of nano silica dispersed in resin were examined by FT-IR, TAG and SEM. The dielectric properties of these hybrid films over a given temperature and frequency ranges have been studied in a point of view of stable chemical bonding of nano Silica filler. The results from IR spectra and SEM photograph indicated that PEI-Silica hybrid film prepared with nano CS sol process has been synthesized in uniform and chemical bonding. The decrease property of dielectric constant with CS content, tangent loss consistent of given frequency and temperature has been explained in terms of the chain movement of polymer through chemical bonging and size effect of nano silica. The new PEI-CS sol hybrid film with such stable chemical and dielectric properties was expected to be used as a high functional coating application in ET, IT and electric power products.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.68-81
• /
• 1995

This paper presents an analytical solution to predict the transient temperature distribution in fillet arc welding. The analytical solution is obtained by solving a transient three -dimensional heat conduction equation with convection boundary conditions on the surfaces of an infinite plate with finite thicknesses, and mapping an infinite plate onto the fillet weld geometry with energy equation. The electric arc heat input on fillet weld and on infinite plate is assumed to have a traveling bivariate Gaussian distribution. To check the validity of the solution, GTA and FCA welding experiments were performed under various welding conditions. The actual isotherms of the weldment cross - sections at various distances from the arc start point are compared with those of simulation result. As the result shows a satisfactory accuracy, this analytical solution can be used to predict the transient temperature distribution in the fiIIet weld of finite thickness under a moving bivariate Gaussian distributed heat source. The simplicity and short calculation time of the analytical solution provides rationales to use the analytical solution for modeling the welding control systems or for an optimization tool of welding process parameters.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.7 no.1
• /
• pp.23-31
• /
• 2011

The objectives of this study are to analyze the performance of a heat pump system with the various heat source and to carry out economic assessment for the heat pump system. The COP of the river water and ground source heat pump system was 20% higher than that of the air source heat pump system because river water and geothermal provide stable operating temperature compared with air temperature throughout the year. In addition, the economic assessment of a heat pump system using air, river water, and geothermal as a heat source was carried out. The ratio of the life cycle operating cost to the life cycle cost increased with the increase of building capacity. The payback period was found to be less than 3.3 and 4.5 years, respectively when the capacity of the river water and ground source heat pump was larger than 10 RT.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.3 no.1
• /
• pp.1-9
• /
• 2007

A steady-state simulation model for Dual-Source Heat Pump(DSHP) of 8RT was presented. A Dual-Source Heat Pump(DSHP) has been designed to make up for the conventional air source heat pumps. The performance evaluation has been conducted under internal standard test conditions such as ISO-13256-1 and KS C 9306. However, as test conditions such as entering water, indoor and outdoor air conditions could not be controlled to satisfy the standard test conditions in outdoor tests, a series of experiments have been conducted with the actual test conditions. Then, computer models for DSHP could be used for the standard condition have developed using EES program. The model was developed from basic thermodynamic principles and heat transfer relations. Most of the parameters were obtained with EES from the actual catalog data. The simulation results were in good agreement with the experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.595-602
• /
• 2012

In this study, for the purpose of reduction of $CO_2$ gas emission and to increase recovery of waste heat from ships, the ORC (Organic Rankine Cycle) is investigated and offered for the conversion of temperature heat to electricity from waste heat energy from ships. Simulation was performed with waste heat from the exhaust gasse which is relatively high temperature and cooling sea water which is relatively low temperature from ships. Various fluid is used for simulation of the ORC system with variable temperature and flow condition and efficiency of system and output power is compared. Finally, 2,400kW output power is obtained by system optimization of the preheater and reheater utilizing waste heat form sea water cooling system.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.1
• /
• pp.100-107
• /
• 2017

3D printing is a technology that converts a computer-generated 3D model into a real object with additive manufacturing technology. A majority of 3D printing technologies uses one material, and this is considered a limitation. In this study, we developed a multi-material 3D printer by adopting dual resin vat and cleaning system with DLP (Digital Light Processing) 3D printing technology. The developed multi-material DLP 3D printer is composed of a manufacturing system, cleaning system, transporting system, and automatic resin recharging system. Various 3D structures were 3D printed with two materials, thus demonstrating the potential. Printing performance of the multi-material DLP 3D printer was studied by performing a comparative surface roughness test and tension test on specimens composed of one material as well as those composed of two materials.