• Journal of Advanced Marine Engineering and Technology
• /
• v.11 no.3
• /
• pp.45-52
• /
• 1987

Generally the factors affected largely by the cold cracking sensitivity of the weld are the quantity of the diffusible hydrogen, the brittleness and hardness of the bond area and the tensile restraint stress. These factors have relation each other, and if we can reduce one of these factors, it becomes instrumental to the root cracks prevention of weld. This study deals with the gravity type-underwater-welding of KR Grade A-3 marine steel plate using E4303 welding electrode in order to compare wet-underwater-welding with in-air- welding, resulting in obtaining the tensile restraint characteristics, the hardness distribution, the quantity of diffusible hydrogen and the macro- and micro-crack properties in both underwater and in-air welds. The main results obtained are as follows: 1) The quantity of diffusible hydrogen measured for 48 hours is about 18cc/100g-weld-metal for the in-air-weld of one pass and about 48cc/100g-weld-metal for the underwater-weld of one pass which is about 3 times penetration of diffusible hydrogen compairing with the case of the in-air-weld. However, it was experimentally confirmed that, by the multi-pass welding of 2 to 5 passes, the diffusible hydrogen in the underwater weld metal can be reduced as much as 27 to 49%. 2) The hardness of the weld metal indicates the highest value in the heat affected zones of underwater weld for more rapid cooling rate, resulting in the higher sensitivity of cold cracking. So, it is desirable to soften the higher hardness in the HAZ by tempering effect such as the multi-pass welding in the underwater welding. 3) At the bond vicinity of the underwater weld HAZ, micro cracks were found as resulted by both more rapid cooling rate and more diffusible hydrogen and also by the stress corrosion cracking under the tensile restraint stress in the underwater. But this could be prevented by the tempering effect of the following weld bead such as the multi-pass welding.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.5
• /
• pp.43-53
• /
• 2010

This study investigates a design optimization of a rotating two-pass rectangular cooling channel with staggered arrays of pin-fins. The radial basis neural network method is used as an optimization technique with Reynolds-averaged Navier-Stokes analysis of fluid flow and heat transfer with shear stress transport turbulent model. The ratio of the diameter to height of the pin-fins and the ratio of the streamwise spacing between the pin-fins to height of the pin-fin are selected as design variables. The optimization problem has been defined as a minimization of the objective function, which is defined as a linear combination of heat transfer related term and friction loss related term with a weighting factor. Results are presented for streamlines, velocity vector fields, and contours of Nusselt numbers, friction coefficients, and turbulent kinetic energy. These results show how fluid flow in a two-pass square cooling channel evolves a converted secondary flows due to Coriolis force, staggered arrays of pin-fins, and a $180^{\circ}$ turn region. These results describe how the fluid flow affects surface heat transfer. The Coriolis force induces heat transfer discrepancy between leading and trailing surfaces, having higher Nusselt number on the leading surface in the second pass while having lower Nusselt number on the trailing surface. Dean vortices generated in $180^{\circ}$ turn region augment heat transfer in the turning region and in the upstream region of the second pass. As the result of optimization, in comparison with the reference geometry, thermal performance of the optimum geometry shows the improvement by 30.5%. Through the optimization, the diameter of pin-fin increased by 14.9% and the streamwise distance between pin-fins increased by 32.1%. And, the value of objective function decreased by 18.1%.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1B
• /
• pp.8-14
• /
• 2000

This paper analyzes and accesses the gain of optically pumped surface-normal MQW optical amplifiers. The proposed amplifiers have the advantage of polarization independence, high coupling efficiency to and from optical fibers, and flexibility of operating wavelength. We analyzed the gain characteristics of 100 - 200-period MQWs and verified the dependence of a strained lattice and selective doping. Theoretical analysis of such MQWs showsa single-pass gain of 3 dB with broad operation bandwidth. A single-pass gain of 2.6 dB is obtained experimentally in an InGaAs/InGaAlAs MQW amplifier, which is compared with calculations. The use of Fabry-Perot interferometer (FPI) structure in an optical amplifier is a useful way to increase the gain, but causes a problem of narrow operation bandwidth when the single-pass gain is low. Therefore, a single-pass gain above 2to 3 dB is a prerequisite to achieve both a high gain and moderate operation bandwidth in FPI-structured opticalamplifiers. We have designed an FPI-structured surface-normal optical amplifier both with a high gain of broad operation bandwidth of 4.6mm, when a single-pass gain is 3 dB.

• Journal of the Institute of Convergence Signal Processing
• /
• v.1 no.1
• /
• pp.58-63
• /
• 2000

This paper describes an efficient algorithm for shot boundary detection in MPEG video stream. There are two types of shot boundary: abrupt and gradual. The proposed algorithm for detecting the abrupt shot boundaries used DCT DC value in compressed domain. The proposed algorithm of the gradual change detection consists of two-pass mechanism. In the first pass, the expected positions of shot boundaries are extracted using ratio value of motion vectors. After decoding frames that are extracted in the first pass, we will make the dissolving image using (n)th and (n+2)th image of expected position. The gradual shot boundaries are selected by similarity of the dissolving image and the image of (n+1)th expected position. As applying the algorithm for detecting shot boundaries, the gradual changes as well as the abrupt changes are detected efficiently. Experimental results indicate that the proposed method is computationally fast for detecting shot boundaries and robust to the variation of the video characteristic that is different for the kind of videos.

• Applied Microscopy
• /
• v.42 no.2
• /
• pp.105-109
• /
• 2012

Electron tomography (ET) of biological specimens is performed from a series of images obtained over a range of tilt angles in a transmission electron microscope. When using the high voltage electron microscope (HVEM), various noises appear in EM images acquired from thick sections by high voltage electron beam. In order to obtain an adequate result in electron tomograms that allow visualization of rather complex and mega-cellular structure such as brain tissue, it is necessary to remove the noise in each original tilt images of thick section. Using band-pass filtering of original tilt images, the filtered images are obtained and used to assemble a reconstructed tomogram. The qualified 3D tomogram from filtered images results in a considerable reduction of the noises compared to conventional tomogram. In conclusion, this study suggests that band-pass filtering is effective to improve the brightness and intensity of HVEM produced tomograms acquired from micron-thick sections of biological specimens.

• Korean Journal of Materials Research
• /
• v.23 no.7
• /
• pp.392-398
• /
• 2013

A two-pass differential speed rolling(DSR) was applied to a deoxidized low-phosphorous copper alloy sheet in order to form a homogeneous microstructure. Copper alloy with a thickness of 3 mm was rolled to 75 % reduction by two-pass rolling at $150^{\circ}C$ without lubrication at a differential speed ratio of 2.0:1. In order to introduce uniform shear strain into the copper alloy sheet, the second rolling was performed after turning the sample by $180^{\circ}$ on the transverse direction axis. Conventional rolling(CR), in which the rotating speeds of the upper roll and lower roll are identical to each other, was also performed by two-pass rolling under a total rolling reduction of 75 %, for comparison. The shear strain introduced by the conventional rolling showed positive values at positions of the upper roll side and negative values at positions of the lower roll side. However, samples processed by the DSR showed zero or positive values at all positions. {100}//ND texture was primarily developed near the surface and center of thickness for the CR, while {110}//ND texture was primarily developed for the DSR. The difference in misorientation distribution of grain boundary between the upper roll side surface and center regions was very small in the CR, while it was large in the DSR. The grain size was smallest in the upper roll side region for both the CR and the DSR. The hardness showed homogeneous distribution in the thickness direction in both CR and DSR. The average hardness was larger in CR than in DSR.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.169-174
• /
• 2018

In this paper, a design method for a wideband LPF for harmonic suppression applications is investigated. The proposed wideband LPF is comprised of four circular slot pairs with different diameters, which are added symmetrically in the ground plane of a CPW transmission line. Four circular slot pairs act as a defected ground structure and provide a wideband low pass characteristic. The circular slot with the smallest diameter is located at the side of port 1, and the diameter of the circular slot is increased as it goes toward port 2. The low pass characteristics of each circular slot are compared with the proposed wideband LPF. The final designed LPF was fabricated on FR4 substrate, and its characteristics were tested. The measured S11 characteristic was maintained at over -3.3 dB in the frequency range of 1.89-20.00 GHz band, whereas the S21 characteristic was less than -21.4 dB in the frequency range of 2.66-20.00 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.6
• /
• pp.8-12
• /
• 2008

A ring resonator based band-pass filter enabling enhanced sideband suppression was proposed and demonstrated. It is composed of a single-ring based band-pass section combined with a band-rejection section based on two different coupled rings. The sideband region of the transfer characteristics of the first band-pass filter section was selectively suppressed by means of the band-rejection section without causing any excessive insertion loss. As a result, the overall transfer characteristics of the proposed filter was unproved so that its sideband suppression was elevated to allow for sharper roll-off and narrower bandwidth. In this work, a conventional single-ring band-pass filter and a proposed filter including the band-rejection section were designed and fabricated. As for the achieved device performance, with the center frequency at about 4 GHz, the sideband suppression ratio was increased as much as 8 dB and the 3-dB bandwidth was reduced from 98 MHz to 48 MHz by about 51% with no remarkable excessive insertion loss as expected. And the quality factor of the device was increased by about 105%.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.214-220
• /
• 2013

Small area LDO (Low drop-out) regulator with pass transistor using body-driven technique is presented in this paper. The body-driven technique can decrease threshold voltage (Vth) and increase the current ID flowing from drain to source in current. The technique is applied to the pass transistor to reduce size of area and maintain the same performance as conventional LDO regulator. A pass transistor using the technique can reduce its size by 5.5 %. The proposed LDO regulator works under the input voltage of 2.7 V ~ 4.5 V and provides up to 150mA load current for an output voltage range of 1.2 V ~ 3.3 V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2189-2194
• /
• 2009

The automatic hot gas by-pass technique is applied to control the capacity of refrigeration and air-conditioning system when operating at part load. In the scheme, the hot gas from the compressor is extracted and injected into the outlet of an evaporator through a hot gas by-pass valve. Thus, In this paper, the hot gas by-pass scheme for CO2 is discussed and analyzed on the basis of mass and energy conservation law. A comparative study of the schemes is performed in terms of the coefficiency of performance (COP) and cooling capacity. The operating parameters considered in this study include compressor efficiency, superheating degree, outlet temperature of gas cooler and evaporating temperature in the R744 vapor compression cycle. The main results were summarized as follows : the superheating degree, outlet temperature and evaporating temperature of R744 vapor compression refrigeration system have an effect on the cooling capacity and COP of this system. With a thorough grasp of these effect, it is necessary to design the compression refrigeration cycle using R744.