• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.285-290
• /
• 1995

High quality $Y_{1}$Ba$_{2}$Cu$_{3}$$O_{7-x}$ thin films have been fabricated by pulsed Nd:YAG laser deposition using an unusual 'off-axis' target-substrate geometry. Various properties of superconducting $Y_{1}$Ba$_{2}$Cu$_{3}$$O_{7-x}$ thin films have been studied systematically as a function of oxygen pressure during the deposition, in both 'on-axis' and the unusual 'off-axis' target substrate geometries. In the 'off-axis' geometry, one can completely eliminate the so-called 'laser droplets' from the film surface and thus obtain smooth high quality films. It is found that films with optimum structural and electrical properties are obtained at a lower oxygen pressure range during the 'off-axis' deposition when compared with that required in the 'on-axis' deposition geometry.

• Journal of the Korean Vacuum Society
• /
• v.1 no.3
• /
• pp.389-394
• /
• 1992

용액분무법으로 (100) MgO 단결정 기판위에 YBa2Cu3O7-x 초전도박막을 제조하 였다. YBa2Cu3O7-x 초전도 박막의 Y, Ba, Cu 원자의 상대적인 비는 EDX의 검출 한계내에 서 1 : 2 : 3이었고, 이는 분무 용액속의 금속이온의 비와 같았다. YBa2Cu3O7-x 초전도 박 막의 결정구조는 단일 상의 사방구조였으며, 기판에 수직인 c축의 방향으로 grain이 성장되 었고, 격자상수 c0는 11.678$\AA$였다. 95$0^{\circ}C$의 공기중에서 10분간 열처리한 박막의 Tc-on=100K, Tc-zero=80K, Jc=2.5 $\times$ 104A/cm2였고, 95$0^{\circ}C$의 흐르는 산소분위기에서 10분간 열처리한 박막의 Tc-on=103K, Tc-zero=80K, Jc=1.0 $\times$ 105A/cm2였다. 초전도 박막의 미세구 조, grain 크기와 grain 경계폭은 제조후 열처리(post-annealing) 시간과 가스 분위기에 강 한 영향을 받았다.

• Journal of the Korean Magnetics Society
• /
• v.4 no.1
• /
• pp.44-47
• /
• 1994

High $T_{c}$ superconducting $Y_{1}Ba_{2}Cu_{3}O_{7-\delta}$ thin film was grown up for c-axis orientation by epitaxial growth method on $LaAlO_{3}$ single crystal substrate. The crystal structures of this thin film were found to be c-axis orientation by X-ray diffraction patterns. Hall effect and resistivity measurements were made by van der Pauw method. Hall resistivity was calculated from the magnetoresistivity by considering thermomagnetic effect. The relation was $pH=p_{s}tan{\alpha}_{n}-QBT\frac{S_s}{K_s}$ The measured Hall resistivity and the calculated one are in good agreement each other.

• Journal of the Korean Ceramic Society
• /
• v.28 no.3
• /
• pp.243-251
• /
• 1991

High-Tc YBa2Cu3O7-x superconducting thin films have been prepared by single-target off-axis RF magnetron sputtering. Optimal ratio of Y : Ba : Cu of the single-target was determined as 1 : 1.65 : 3.35 in order to obtain the stoichiometric films. Tc, crystalline phase, and microstructures of the surface and cross-section of the ex-situ YBa2Cu3O7-x thin films on MgO(100) had a Tc, zero of 80K, and the films on LaAlO3/Si had a Tc, on-set of 90 K and a Tc, zero of 70 K.

• Progress in Superconductivity
• /
• v.13 no.1
• /
• pp.7-11
• /
• 2011

The effects of Sm:Ba:Cu composition ratio in SmBCO coated conductor on their superconducting properties were investigated. The SmBCO coated conductors were fabricated by reactive co-evaporation method using EDDC(Evaporation using Drum in Dual Chamber) system. In this system, we could obtain various samples with different composition ratios in a batch by the technique providing composition gradient at deposition zone. From the specimens prepared by EDDC system, we found that composition ratio is uniform parallel to the drum axis, but gradient along the circumferential direction of the drum. We installed a shield having parallelogram open area between the deposition chamber and the evaporation chamber in EDDC system, and attached a 30 cm long template, which is parallel to drum axis, onto the drum surface. In this configuration, we could obtain SmBCO coated conductors having a gradient composition along the length of template. We measured the composition ratios and surface morphologies with periodic interval by SEM and EDAX, and confirmed the profile of composition ratio. We also measured critical current using non-contact Hall probe critical current measurement system and thereby could plot composition ratio vs. critical current. The maximum critical current was obtained, and the surface morphology with the shape of roof tile was observed at the corresponding composition ratio of Sm:Ba:Cu = 1.01:1.99:4.87. It was also found that composition ratio had an effect on not only critical current but also surface morphology.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1332-1-1332-4
• /
• 1998

This paper described design and simulation of the high-Tc superconducting (HTS) microstrip bandpass filter (BPF) on MgO substrate using $Y_1Ba_2Cu_3O_{7-x}$ films that show superconductivity ${at \fallingdotseq}90$ K. Design parameters for the characteristic of the bandpass filter in Ku-band were obtained by approximate design formulas. It used parallel coupled stripline stepped impedance resonators (SIR). Microwave design system, MDS(EEsorf S/W) was used to derive the optimal pattern of the filters and to simulate frequency response. In computer-aided results, optimally designed HTS filters got good performance compared with the gold counter-parts on frequency response $S_{21}$, $S_{11}$.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.185-188
• /
• 1999

Biepitaxial Y$_1Ba_2Cu_3O_{7-x}$ (YBCO) and La$_{0.2}Sr_{0.8}MnO_3$ (LSMO) thin films have been prepared on SrTiO$_3$ buffer layer and MgO seed layer grown on Al$_2O_3$(11${\bar{2}}$0)substrates by dc-sputtering with hollow cylindrical targets, respectively. We charaterized Josephson properties and significantly large magnetoresistance in YBCO and LSMO films with 45$^{\circ}$ grain boundary junction, respectively. The observed working voltage (I$_cR_n$) at 77 K in grain boundary junction was below 10${\mu}$V, which is typical I$_cR_n$ value of single biepitaxial Josephson junction. The field magnetoresistance ratio (MR) of LSMO grain boundary juncoon at 77K was enhanced to 13%, which it was significant MR value with high magnetic field sensitivity at a low field of 250 Oe. These results indicate that inserting the insulating layer instead of the grain boundary layer with metallic phase can be possible to apply a new SIS Josephson junction and a novel magnetic device using spin-polarized tunneling junction.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.361-363
• /
• 1995

High quality $Y_1Ba_2Cu_3O_{7-x}$ thin films have been fabricated by pulsed Nd:YAG laser deposition using an unusual 'off-axis' target-substrate geometry. Various properties of superconducting $Y_1Ba_2Cu_3O_{7-x}$ thin films have been studied systematically as a function of oxygen pressure during the deposition, in both 'on-axis' and the unusual 'off-axis' target substrate geometry. In the 'off-axis' geometry, one can completely eliminate the so-called 'laser droplets' form the thin surface and thus obtain smooth high qualify films. It is found that films with optimum structural and electrical properties are obtained at a lower oxygen pressure range during the 'off-axis' deposition when compared with that required in the 'on-axis' deposition geometry.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.16-20
• /
• 2004

YB $a_2$C $u_3$$O_{7-x}$ (YBCO) films were deposited on (100) SrTi $O_3$ single crystal substrates by a metal organic chemical vapor deposition (MOCVD) system of hot-wall type using single liquid source. Under the condition of the mole ratio of Y(tmhd)$_3$:Ba(tmhd)$_2$:Cu(tmhd)$_2$= 1:2.1:2.9. the deposition pressure of 10 Torr. the MO source line speed of 15 cm/min. the Ar/ $O_2$ flow rate of 800/800 sccm. YBCO films were prepared at the deposition temperatures of 780∼89$0^{\circ}C$. In case of the YBCO films with 2.2 ${\mu}{\textrm}{m}$ thickness deposited for 6 minutes at 86$0^{\circ}C$. XRD pattern showed complete c-axis growth and SEM morphology showed dense and crack-free surface. The atomic ratios of Ba/Y and Cu/Ba in the film were 1.92 and 1.56. respectively. The deposition rate of the film was as high as 0.37 ${\mu}{\textrm}{m}$/min. The critical temperature ( $T_{c.zero}$) of the film was 87K. The critical current of the film was 104 A/cm-width. and the critical current density was 0.47 MA/$\textrm{cm}^2$. For the thinner film of 1.3 ${\mu}{\textrm}{m}$ thickness. the critical current density of 0.62 MA/$\textrm{cm}^2$ was obtained.d.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.92-96
• /
• 2005

YBCO thin films on metal substrates were prepared by the metal-organic deposition using trifluoroacetates (TFA-MOD). To compensate the loss of Ba element from the precursor films due to the reaction with $CeO_2$ cap layer, we have employed Ba-excessive precursor solutions of $YBa_{2+x}Cu_{3}O_{7-{\delta}}$ ($0{\le}x{\le}0.1$). The precursor solutions were dip-coated on the metal substrates with $CeO_2$ cap layer, initially heated up to $400^{\circ}C$, and finally fired at the various high temperatures for 2 h in a reduced oxygen atmosphere. With this approach, YBCO films possessing critical temperature over 85 K could be successfully prepared on the metal substrates. The highest $T_{c,zero}$ value of 86 K was obtained from the Ba-excessive YBCO film of x=0.005 in $YBa_{2+x}Cu_{3}O_{7-{\delta}}$ fired at $750^{\circ}C$ for 2 h. However, unexpected $T_c$ suppression even in Ba-excessive YBCO samples requires further identification.