• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.571-575
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature$(350\;to\;550^{\circ}C)$. $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSSCs were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). Below sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively lower due to lower open circuit voltage. Oppositely, above sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively higher due to higher open circuit voltage. In both cases, lower fill factor (FF) was observed. However, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSSCs were mutually complementary, enhancing highest fill factor and efficiency. Such results can be explained in comparison of surface morphology with schematic diagram of energy states on the $TiO_2$ electrode surface. Consequently, it was considered that optimum sintering temperature of a-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1699-1702
• /
• 2012

$TiO_2$ nanostructures with various morphologies like cubes, spheres, hexahedral pillars and spherical tubes were synthesized by microwave-assisted hydrothermal process. Each structure was obtained by changing the relative concentrations of titanium tetraisoproxide (TTIP), tetrabutylammonium hydroxide (TBAH) and ethanol. Scanning electron microscopy (SEM), transmission electoron microscopy (TEM), X-ray diffraction and Brunauer-Emmett-Teller (BET) surface area analysis were used to characterize the synthesized $TiO_2$ nanostructures. From these results, it has been proved that $TiO_2$ structure could be controlled to have specific morphology, size, surface area, pore volume and pore size distribution.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.537-544
• /
• 2001

Anatase $TiO_2$thin films as a photocatalyst were prepared by the reactive magnetron sputtering process. The $TiO_2$thin films were deposited on Si substrates under the various conditions : oxygen partial pressure, working pressure, sputtering time, and D.C. power. The photocatalystic degradation of $TiO_2$thin film have been studied to examine the contribution of surface morphology and crystallinity. The thin films with a good crystallinity or a rough surface showed a high photocatalytic degradation rate on phenol and E.coli 078 experiment. Compared with that of only UV radiation, the photocatalytic efficiency of $TiO_2$thin film under the UV radiation and the $O_2$ flow increased. We found that the crystallity and the morphology were the important factors on the photocatalytic efficiency of TiO$_2$thin film.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.05a
• /
• pp.70-70
• /
• 1999

• Bulletin of the Korean Chemical Society
• /
• v.34 no.10
• /
• pp.2883-2888
• /
• 2013

To enhance the power conversion efficiency of dye-sensitized solar cell (DSSC), the surface of titanium dioxide ($TiO_2$) photoelectrode was modified by hydroxylation treatment with $NH_4OH$ solution at $70^{\circ}C$ for 6 h. The $NH_4OH$ solutions of various concentrations were used to introduce the hydroxyl groups on $TiO_2$ surface. As the concentration of $NH_4OH$ was increased, the short-circuit current density ($J_{SC}$) value and conversion efficiency of solar cells were increased because the amount of adsorbed dye molecules on $TiO_2$ surface was increased. As a result of the surface modification to introduce hydroxyl groups, the concentration of adsorbed dye on the $TiO_2$ surface could be improved up to 32.61% without the changes of morphology, surface area and pore volume of particles. The morphology, the specific surface area, the pore volume and the chemical states of $TiO_2$ surface were characterized by using FE-SEM, $N_2$ adsorption-desorption isotherms and XPS measurements. The amount of adsorbed dye and the performance of fabricated cells were analyzed by using UV-Vis absorption spectroscopy and solar simulator.

• Particle and aerosol research
• /
• v.7 no.3
• /
• pp.79-85
• /
• 2011

Porous $TiO_2-SiO_2$ particles were synthesized by co-assembly of nanoparticles of $TiO_2$ and $SiO_2$ in evaporating aerosol droplets. Poly styrene latex (PSL) particles were employed as a template of porous particles. Flowrate of dispersion gas, weight ratio of $TiO_2/SiO_2$ and $SiO_2$ concentration in the precursor, and PSL size were chosen as process variables. The morphology, crystal structure, chemical bonding, and pore size distribution were analyzed by FE-SEM, XRD, FT-IR, BET. The morphology of porous $TiO_2-SiO_2$ particles was spherical and the average particle size range were from 1 to $10{\mu}m$. The particles were composed of meso and macro pores. The average particle diameter and pore volume of the as prepared particles were dependant on process variables. It was found that UV-Vis absorption of the porous particles was comparable with pure $TiO_2$ nanoparticles even though $TiO_2/SiO_2$ ratio is low in the porous particles.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.334-340
• /
• 2002

$TiO_2$-coated fly ash was synthesized by dropping method of coating agent in order to get $TiO_2$ coating layer with high photocatalytic activity on the surface of coal fly ash. The properties of the $TiO_2$ coating layer such as morphology, crystal structure, crystal size and photocatalytic activity were compared with those of the $TiO_2$-coated fly ash prepared by the traditional method of precipitation. $TiCl_4$ aqueous solution was used as a titanium stock solution and $NH_4HCO_3$ was used as a precipitant. The $TiO_2$ coating layer obtained by dropping method of coating agent was more uniform than that coated by precipitation. However, the crystal of $TiO_2$ coated by dropping method of coating agent was easy to grow by heat treatment because of the small primary particle size and bulky morphology, and its photocatalytic activity was consequently lower than that of the $TiO_2$ coated by precipitation. The $TiO_2$ coating layer obtained by both methods had a crystal structure of anatase, and the temperature of phase transformation into rutile was 90$0^{\circ}C$. The minimum crystal size of $TiO_2$ for the highest photocatalytic activity was found to be about 10nm.

• Environmental Engineering Research
• /
• v.16 no.2
• /
• pp.81-90
• /
• 2011

Different weight percentages of Ag, Pt, and Au doped nano $TiO_2$ were synthesized using the acetic acid hydrolyzed sol-gel method. The crystallite phase, surface morphology combined with elemental composition and light absorption properties of the doped nano $TiO_2$ were comprehensively examined using X-ray diffraction (XRD), $N_2$ sorption analysis, transmission electron microscopic (TEM), energy dispersive X-ray, and DRS UV-vis analysis. The doping of noble metals stabilized the anatase phase, without conversion to rutile phase. The formation of gold nano particles in Au doped nano $TiO_2$ was confirmed from the XRD patterns for gold. The specific surface area was found to be in the range 50 to 85 $m^2$/g. TEM images confirmed the formation a hexagonal plate like morphology of nano $TiO_2$. The photocatalytic activity of doped nano $TiO_2$ was evaluated using 4-chlorophenol as the model pollutant. Au doped (0.5 wt %) nano $TiO_2$ was found to exhibit higher photocatalytic activity than the other noble metal doped nano $TiO_2$, pure nano $TiO_2$ and commercial $TiO_2$ (Degussa P-25). This enhanced photocatalytic activity was due to the cathodic influence of gold in suppressing the electron-hole recombination during the reaction.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.11
• /
• pp.3991-3995
• /
• 2011

$TiO_2-SiO_2-In_2O_3$ nanocomposite thin film was deposited on the glass substrates using a dip coating technique. The morphology, surface composition, surface hydroxyl groups, photocatalytic activity and hydrophilic properties of the thin film were investigated by AFM, XPS, methyl orange decoloring rate and water contact angle measurements. The hydroxyl content for $TiO_2$, $TiO_2-SiO_2$ and $TiO_2-SiO_2-In_2O_3$ nanocomposite films was calculated to be 11.6, 17.1 and 20.7%, respectively. $TiO_2-SiO_2-In_2O_3$ film turned superhydrophilic after 180-min irradiation with respect to pure $TiO_2$ and $TiO_2-SiO_2$ thin films. The photocatalytic decomposition of methyl orange for $TiO_2$, $TiO_2-SiO_2$ and $TiO_2-SiO_2-In_2O_3$ thin films was measured as 38.19, 58.71 and 68.02%, respectively. The results indicated that $SiO_2$ and $In_2O_3$ had a significant effect on the hydrophilic, photocatalytic and self-cleaning properties of $TiO_2$ thin film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.4
• /
• pp.167-172
• /
• 2013

Titanium dioxides nanoparticles coated aluminum oxide powders were fabricated by pulsed laser deposition (PLD) with Nd : YAG laser at 266 nm. The Pulse laser energy is 100 mJ/pulse. During the irradiation of the focused laser on the $TiO_2$ target, Ar gas is supplied into the chamber. The gas pressure is varied in a range of $1{\times}10^{-2}$ to 100 Pa. Titanium dioxides nanoparticles deposited aluminum oxide powders were characterized by using energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HR-TEM), in order to understand the effect of Ar background gas on surface morphology and properties of the powders. The coated $TiO_2$ nanoparticles had nanosized spherical shape and the crystallite sizes of 10~30 nm. The morphology of coated $TiO_2$ nanoparticles is not affected by gas pressure. However, the particle size and crystallinity slightly increased with the increase of gas pressure. According to this technique, the size and crystallinity of nanoparticles can be easily controlled by controlling pressure during the laser irradiation.