• 한국결정성장학회지
• /
• 제12권1호
• /
• pp.7-10
• /
• 2002

$TiO_2$ 박막을 금속유기화합물인 Titanium-naphthenate의 코팅-열분해법으로 제조하였다. 출발물질은 Ti-naphthenate를 toluene에 희석한 용액을 사용하였으며 기판은 slide glass를 사용하였다 Titanium-naphthenate 용액을 spin-coating법으로 기판에 코팅하고 $450^{\circ}C$에서 열터리하여 $TiO_2$ 박막을 제조하였다 제조한 박막의 특성을 UV/Vis, XRD 및 SEM 등으로 박막의 투과율, 굴절률, 결정상 및 표면 형상을 분석하였다. Slide glass 위에 제조한 TiO$_2$ 박막은 투과율은 70~90%이며 420nm에서의 굴절율은 2.7이었다. $TiO_2$박막은 anatase상을 나타내었고 실타래 형상의 주름을 가진 표면을 나타내었다

• 한국환경과학회지
• /
• 제31권8호
• /
• pp.677-689
• /
• 2022

In order to photocatalytically treat organic matter (COD_Cr) and chromaticity effectively, chemical coagulation and sedimentation processes were employed as a pretreatment of the leachate produced from landfill in Jeju Island. This was performed using FeCl₃·6H₂O as a coagulant. For the treated leachate, UV/TiO₂ and UV/TiO₂/H₂O₂ systems were investigated, using 4 types of UV lamps, including an ozone lamp (24 W), TiO₂ as a photocatalyst, and/or H₂O₂ as an initiator or inhibitor for photocatalytic degradation. In the chemical coagulation and sedimentation process using FeCl₃·6H₂O, optimum removal was achieved with an initial pH of 6, and a coagulant dosage of 2.0 g/L, culminating in the removal of 40% COD_Cr and 81% chromaticity. For the UV/TiO₂ system utilizing an ozone lamp and 3 g/L of TiO₂, the optimum condition was obtained at pH 5. However, the treated COD_Cr and chromaticity did not meet the emission standards (COD_Cr: 400 mg/L, chromaticity: 200 degrees) in a clean area. However, for a UV/TiO₂/H₂O₂ system using 1.54 g/L of H₂O₂ in addition to the above optimum UV/TiO₂ system, the results were 395 mg/L and 160 degrees, respectively, which were within the emission standard limits. The effect of the UV lamp on the removal of COD_Cr, and chromaticity of the leachate decreased in the order of ozone (24 W) lamp > 254 nm (24 W) lamp > ozone (14 W) lamp > 254 nm (14 W) lamp. Only COD_Cr and chromaticity treated with the ozone (24 W) lamp met the emission standards.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.511-511
• /
• 2007

Low-emissivity (low-e) coatings with visible transparency have attracted increased interest m reducing heat radiation loss through window panes from ecological and sustainable aspects. $TiO_2$-silver transparent thin films for low-e have good properties for UV and IR blocking as well as photocatalyst compared to that with commercial UV blocking films such as fluorine doped oxide (FTO), antimony doped tin oxide (ATO), etc. In this study, transparent $TiO_2$-silver thin films were prepared by successive ink-jet printing of commercial nano silver and $TiO_2$ sol. The $TiO_2$ sol, as ink for ink-jet printing, were synthesized by hydrothermal process in the autoclave externally pressurized with $N_2$ gas of 200 bar at $120^{\circ}C$ for 10 hrs. The synthesized $TiO_2$ sols were all formed with brookite phase and their particle size was several to 30 nm. At first nano sized silver sol was coated on glass substrate, after that $TiO_2$ sol was coated by ink-jet printing. With increasing coating thickness of $TiO_2$-silver multilayer by repeated ink-jet coating, the absorbance of UV region (under 400nm) and IR region (over 700nm) also increase reasonably, compared to that with commercial UV blocking films.

• 한국환경과학회지
• /
• 제16권4호
• /
• pp.433-440
• /
• 2007

The photodegradation and by-products of the gaseous toluene with $TiO_2$ (P25) and short-wavelength UV ($UV_{254+185nm}$) radiation were studied. The toluene was decomposed and mineralized efficiently owed to the synergistic effect of photochemical oxidation in the gas phase and photocatalytic oxidation on the $TiO_2$ surface. The toluene by the $UV_{254+185nm}$ photoirradiated $TiO_2$ were mainly mineralized $CO_2$ and CO, but some water-soluble organic intermediates were also formed under severe reaction conditions. The ozone and secondary organic aerosol were produced as undesirable by-products. It was found that wet scrubber was useful as post-treatment to remove water-soluble organic intermediates. Excess ozone could be easily removed by means of a $MnO_2$ ozone-decomposition catalyst. It was also observed that the $MnO_2$ catalyst could decompose organic compounds by using oxygen reactive species formed in process of ozone decomposition.

• 멤브레인
• /
• 제21권4호
• /
• pp.351-359
• /
• 2011

For advanced drinking water treatment of high turbidity water, we used the hybrid process that was composed of photocatalyst packing in space of between outside of multi-channel ceramic microfiltration membrane and membrane module inside. Photocatalyst was polypropylene (PP) beads coated $TiO_2$ powder by CVD (chemical vapor deposition) process. Instead of natural organic matters (NOM) and fine inorganic particles in natural water source, standard NOM solution was prepared with humic acid and kaolin. Water-back-flushing of 10 sec was performed per every period of 10 min to minimize membrane fouling. Resistance of membrane fouling ($R_f$) increased and J decreased as concentration of humic acid changed from 2 mg/L to 10 mg/L, and finally the highest total permeate volume ($V_T$) could be obtained at 2 mg/L. Then, treatment efficiency of turbidity and $UV_{254}$ absorbance were above 96.4% and 78.9%, respectively. As results of treatment portions by membrane filtration, photocatalyst adsorption, and photo-oxidation in (MF), (MF + $TiO_2$), (MF + $TiO_2$ + UV) processes, turbidity was treated little by photocatalyst adsorption, and photo-oxidation. However, treatment portions of $UV_{254}$ absorbance by adsorption (MF + $TiO_2$) and photo-oxidation (MF + $TiO_2$ + UV) at humic acid of 4 mg/L and 6 mg/L were above 9.0, 9.5 and 8.1, 10.9%, respectively.

• 한국대기환경학회지
• /
• 제17권4호
• /
• pp.363-370
• /
• 2001

In this study, TiO$_2$, the popular photocatalyst, was used to decompose ethanol. TiO$_2$was prepared by the sol -gel method and coated on pyrex stick. A 15W, UV-A lamp was used as the UV light source and il gas chromatography (HP 5890) was used to confirm the concentrations of ethanol, $CO_2$and the intermediates. Variation of preparation parameters and calcination temperature for TiO$_2$photocatalysts in the sol -gel method caused changes of ethanol decomposition activity. The best ethanol photodecomposition activity was obtained on the sample when prepared with 0.14 mol of HCI, a mol of ethanol and 1.3 mol of TTIP ware mixed in sol-gel process and calcinated at 50$0^{\circ}C$ for 3 hours. Acetaldehyde was detected as an intermediate and decomposed to carbon dioxide and water at the end of the reaction.

• 한국재료학회지
• /
• 제19권9호
• /
• pp.481-487
• /
• 2009

The photocatalysts of Fe-ACF/$TiO_2$ compositeswere prepared by the sol-gel method and characterized by BET, XRD, SEM, and EDX. It showed that the BET surface area was related to adsorption capacity for each composite. The SEM results showed that ferric compound and titanium dioxide were distributed on the surfaces of ACF. The XRD results showed that Fe-ACF/$TiO_2$ composite only contained an anatase structure with a Fe mediated compound. EDX results showed the presence of C, O, and Ti with Fe peaks in Fe-ACF/$TiO_2$ composites. From the photocataytic degradation effect, $TiO_2$ on activated carbon fiber surface modified with Fe (Fe-ACF/$TiO_2$) could work in the photo-Fenton process. It was revealed that the photo-Fenton reaction gives considerable photocatalytic ability for the decomposition of methylene blue (MB) compared to non-treated ACF/$TiO_2$, and the photo-Fenton reaction was improved by the addition of $H_2O_2$. It was proved that the decomposition of MB under UV (365 nm) irradiation in the presence of $H_2O_2$ predominantly accelerated the oxidation of $Fe^{2+}$ to $Fe^{3+}$ and produced a high concentration of OH radicals.

• 한국재료학회지
• /
• 제11권7호
• /
• pp.537-544
• /
• 2001

$TiO_2$광촉매릉 반응성 스퍼터링법을 이웅하여 박막으로 제조하고 유기물 및 살균실험을 통하여 미세조직이 광촉매 효율에 미치는 영향을 조사하고자 하였다. 광촉매 효율측정을 위하여 페놀분해실험 및 E.coli 078을 이용한 살균실험을 행하였다. $TiO_2$박막에 의한 페놀분해실험 시, 전자수용체인 산소의 공급에 의하여 분해효율이 2배까지 증가하였다. E.coli 078분해실험의 경우, 광촉매 $TiO_2$박막을 사웅하여 살균하였을때 UV만 조사하여 살균하였을 경우 보다 분해효율이 최고 70% 이상 증가하였다. 페놀분해실험과 E.coli 078 살균실험 결과 저결정성 박막의 경우 분해능이 매우 미약하였으며, 표면조도가 높고 결정성이 우수한 박막의 경우에 높은 광촉매 효율을 나타내어$TiO_2$박막의 광촉매 효과는 표면형상과 결정성이 매우 중요한 인자로 작용하였다.

• 한국세라믹학회지
• /
• 제44권3호
• /
• pp.137-141
• /
• 2007

$La_{2}O_{3}-TiO_{2}-SiO_{2}$ glass, a type that could not obtained so far by the conventional melting method, was prepared successfully using a sol gel process. Glass derived with the sol-gel process has compositions of $5La_{2}O_{3}-5TiO_{2}-90SiO_{2},\;5La_{2}O_{3}-10TiO_{2}-85SiO_{2}$, and $5La_{2}O_{3}-20TiO_{2}75SiO_{2}$. The UV-visible absorption edge of all glass compositions was below 400 nm. The measured density is in the range of 2.55-2.89, and was nearly identical to the calculated density and the refractive index of the glasses derived from the sol-gel ranges from 1.545 to 1.645. The molar additive coefficient of $TiO_{2}$ measured in this ternary system is lower than the calculated value, while the value of $La_{2}O_{3}$ is higher.

• 한국안광학회지
• /
• 제12권1호
• /
• pp.17-22
• /
• 2007

Ti-나프텐산염과 금속을 출발원료로 사용하고, 스핀코팅-열분해법을 이용하여 실리카 유리위에 박막을 제조하였다. 도포된 박막은 $500^{\circ}C$ 공기에서 10min동안 열처리하였다. 이를 5회 코팅한 박막은 마지막으로 공기에서 $600^{\circ}C$에서 30min으로 하였다. 박막의 특성을 분석하기 위하여 X-선 회절 분석, 전자현미경, UV스펙트럼을 이용하여 분석하였다. 밴드갭에서 가장 큰 장파장 쪽으로 이동은 Fe을 도핑한 $TiO_2$ 박막이었다.