• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1195-1202
• /
• 1996

To prepare the dielectric thin films of (Pb1-xSrx)TiO3 (x=0.1, 0.2, 0.3, 0.35, 0.5) by the sol-gel process titanium (IV) isopropoxide (Ti[OCH(CH3)2]4) and Pb Sr, acetate were used therefore the thin films were fabricated by dip-coating method. Stability of the sol decreased with addition of Sr content thin films could be fabricated up to 35mol% Over this range precipitation of sol occured thin films couldn't be obtained. Transmittance of thin films at visible range decreased with the increase of heat-treatment temperature but exhibited transmit-tance above 60% in all case. Moreover transmittance of thin films at visible range slightly increased with of addition of Sr,. When thin film containing 30 mol% srontium was heated at 600℃ the best perovskite phase was obtained. The dielectric constant (ε) was 280 and dielectric loss factor (tan δ) was 0.021 and curie tempera-ture (Tc) decreased with the increase of addition of Sr.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.138-144
• /
• 1995

It is commonly believed that high permittivity materials will be necessary for future high density Gbit DRAMs. In a first part, we explain the choice of SrTiO3 by ECR MOCVD for Gbit-scale DRAMs. In a second part, after describing the ECR MOCVD system and presenting the requirements SrTiO3 thin films should meet for use in Gbit-scale DRAMs, the physical and electrical properties of srTiO3 thi film prepared by ECR MOCVD are then studied. A stacked capacitor technology, suitable for use in 1 Gbit DRAM, and comprising high permittivity SrTiO3 thin films prepared by ECR MOCVD at $450^{\circ}C$ on electron beam and RIE patterned RuO2/TiN storage nodes is finally described.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.649-652
• /
• 1999

The (Ba, Sr)TiO$_3$(BST) thin films were fabricated on Pt/Ti/SiO$_2$/Si substrate by RF sputtering technique. The structural properties of the BST thin films were investigated with substrate temperature by XRD, SEM, EDS and AES depth profils. Increasing the substrate temperature, barium multi titanate phases were decreased. The BST thin film had a structure of perovskite type, and had peaks of (100), (200) at the substrate temperature of 50$0^{\circ}C$. When the BST thin films were deposited at the substrate temperature of 50$0^{\circ}C$, the composition ratio of Ba/sr was 52/48.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.607-611
• /
• 2000

Zr modified $(Ba_{1-x},Sr_x)TiO_3$ thin films as capacitor for high density DRAM were deposited by r.f. magnetron sputtering. The films deposited at various chamber pressure exhibited a polycrystalline structure. The Zr/Ti ratio of the films increased significantly with decreasing the chamber pressure and this variation affected the microstructure and surface roughness of films When chamber pressure increased dielectric constant of the films effected due to decrease of Zr. The thin films prepared in this study show dielectric constant of 380 to 525 at 100KHz. The variation of capacitance and polarization measured as a function of bias voltage suggested that all films were paraelectric phases. Leakage current exhibited smaller value as chamber pressure decrease and the leakage current density of the films deposited above 10mTorr was $10^{-7}~10^{-8}A/cm^2$ order at 200kV/cm. $(Ba_{1-x},Sr_x)(Ti_{1-y},Zr_y)O_3$ thin films in this study appeared to be potential thin film capacitor for high density DRAM.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.5
• /
• pp.265-269
• /
• 2000

$(Ba, Sr)TiO_3$thin films were etched with a magnetically enhanced inductively coupled plasma (MEICP) at different CF4/Ar gas mixing ratios. Experimental was done by varying the etching parameters such as rf power, dc bias and chamber pressure. The maximum etch rate of the BST films was $1800{AA}/min$ under $CF_4/(CF_4+Ar)$ of 0.1, 600 W/350 V and 5 mTorr. The selectivity of BST to Pt and PR was 0.6, 0.7, respectively. X-ray photoelectron spectroscopy (XPS) results show that surface reaction between Ba, Sr, Ti and C, F radicals occurs during the (Ba, Sr)TiO3 etching. To analyze the composition of surface residue after the etching, films etched with different CF_4/Ar$ gas mixing ratio were investigated using XPS and secondary ion mass spectroscopy (SIMS).

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1075-1079
• /
• 1999

LaSrCoO3 thin films were spin-coated onto the SrTiO3(100) substrates by the chemical solution process. X-ray diffraction $\theta$-2$\theta$ scans and X-ray diffraction $\beta$ scans were used to determine the crystallinity and in -plane alignment behavior of the films. The X-ray diffraction pattern showed the film obtained by annealing at 80$0^{\circ}C$ was highly oriented. The X-ray diffraction pole-figure analysis and reciprocal-space mapping (2$\theta$-$\Delta$$\omega$ scans) of the resulting film showed that the film comprising the pseduocubic phase had an epitaxial relationship with the SriO3 substrate.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.286-291
• /
• 1998

$SrTiO_3$[ST] thin films were fabricated on $RuO_2$bottom electrodes by RF magnetron sputtering with various $Ar/O_2$ratio in sputtering gas. As the content of oxygen increases, the leakage current of ST films measured at $10^5$ V/cm decreases from $2.0{\times}10^{-6}A/{\textrm}{cm}^2(Ar/O_2=10/0)$ to $3.8{\times}10^{-7}A/{\textrm}cm^2(Ar/O_2=5/5)$, and the dielectric constant of ST films increases from $70(Ar/O_2=10/0)$ to $190(Ar/O_2=5/5)$. The improvement of electrical properties of ST films is mainly due to the structural modification of ST films such as better crystallinity, smooth surface morphology with the increase of oxygen content in the sputtering gas.

• Proceedings of the KIEE Conference
• /
• 1999.11a
• /
• pp.31-34
• /
• 1999

In the present study, we fabricated stoichiometric $(Ba_{1-x}Sr_x)TiO_3$ thin films at various substrate temperature and contents using of magnetron sputtering method on optimized Pt-based electrodes (Pt/TiN/$SiO_2$/Si). The substate temperature deposited at 200[ $^{\circ}C$], 400[$^{\circ}C$] and 600[$^{\circ}C$] and crystalline BST thin films show above 400[$^{\circ}C$]. Also, the composition of $(Ba_{1-x}Sr_x)TiO_3$ thin films deposited on Si wafer substrate at 400[$^{\circ}C$] were closed to stoichiometry($1.015{\sim}1.093$ in A/B ratio), but compositional deviation from a stoichiometry is larger as $SrCO_3$ is added. The drastic decrease of dielectric constant and increase of dielectric loss in $(Ba_{1-x}Sr_x)TiO_3$thin films is observed above 100[kHz]. V-I characteristics of $(Ba_{1-x}Sr_x)TiO_3$ thin films show the decrease of leakage current with the increase of $SrCO_3$ contents.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.933-938
• /
• 2002

(Ba,Sr)TiO$_{4}$ (BST) thin films on Pt/Ti/SiO$_{2}$/Si substrates were deposited by a sol-gel method and the etch characteristics of BST thin films have been investigated as a function of gas mixing ratio. The maximum etch rate of the BST films was 440 $AA$/min under such conditions as: CF$_{4}$(CF$_{4}$＋Ar) of 0.2, RF-power of 700 W, DC-bias voltage of -200 V, pressure of 15 mTorr and substrate temperature of 30 $^{circ}C$. The selectivities of BST to Pt, SiO$_{2}$ and PR were 0.38, 0.25 and 0.09, respectively. In the XPS (X-ray photoelectron spectroscopy) analysis, Barium (Ba) and Strontium (Sr) component in BST thin films formed low volatile compounds such as BaFx, SrFx, which are forms by the chemical reaction with F atoms and is removed by Ar ion bombardment. Titanium (Ti) is removed by chemical reaction such as TiF with ease. The result of secondary ion mass spectrometry (SIMS) analysis confirmed the existence of the BaFx, SrFK, TiFx.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.73-76
• /
• 2001

We deposited epitaxial $Ba_{0.6}$S $r_{0.4}$Ti $O_3$(BST) films having thickness of 400 nm on MgO(001) substrates, where a 10 nm thick $Ba_{1-x}$S $r_{x}$Ti $O_3$(x=0.1-0.7) interlayer was inserted between BST and MgO to manipulate the stress of the BST films. Since the main difference of those epitaxial BST films was the lattice constant of the interlayers, we were very successful in controlling the stress of the BST films. BST films under small tensile stress showed larger dielectric constant than that without stress as well as those under compressive stress. Stress relaxation was investigated using epitaxial BST films with various thicknesses grown on different interlayers. For BST films grown on $Ba_{0.7}$S $r_{0.3}$Ti $O_3$ interlayers, the critical thickness was about 600 nm. On the other hand, the critical thickness of single-layer BST film was less than 100 nm.00 nm.m.m.m.