• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.865-872
• /
• 1991

LAS (lithium aluminosilicate) sol was synthesized using the hydrolysis-condensation reaction of TEOS, chelated Al(OBus)3 and LiNO3 with H2O in alcohol (ethanol+2-propanol) medium. Lowering Li content by a factor of 1/2 significantly enhanced densification and retarded the crystallization of LAS gel by ~30$0^{\circ}C$. Dense LAS specimen with essentially pore-free microstructure was obtained by sintering the sol-gel derived gel at 80$0^{\circ}C$ for 4 h and annealing at 120$0^{\circ}C$ for 2 h. Similary, a mixed colloidal processing was attempted as a convenient, alternative route for the fabrication of dense LAS sintered body. The $\beta$-spodumene seeding (~0.8 ${\mu}{\textrm}{m}$) in the sol-gel derived LAS modified the sequence of phase transformations and lowered the temperature of crystallization by ~12$0^{\circ}C$. Combining the epitaxial seeding with the sol-gel process, we could lower the crystallization temperature to the sintering temperature range (~80$0^{\circ}C$) and, demonstrate a possibility of making the viscous sintering/crystallization as a continuous as a continuous unit process.

• Journal of the Korean Ceramic Society
• /
• v.34 no.7
• /
• pp.774-780
• /
• 1997

Porous low reflective coating films of SiO2.ZrO2 system were prepared from the mixed alkoxide solutions of Zr(O-nC3H7)4 and partially prehydrolyzed TEOS by the sol-gel method using the dip-coating technique. In the case of 90SiO2.10ZrO2 porous coating films with HCl and H2O content was 0.3 mole and 4 mole, 378 m2/g of the specific surface area, 0.254 cm3/g of total pore volume, 30-50$\AA$ of average pore diameter. The transmittance of 90SiO2.10ZrO2 porous coated films was 95.38% at the wavelength of 550 nm, compared with the parent glass, the transmittance was increased with 4.38%.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.57-62
• /
• 1995

The coating condition of reproducible anti-reflective coating film and the light transmittance characteristics of the prepared anti-reflective coating glass were investigated as a study for the preparation of single-layer anti-reflective coating glasss. In case of coating with the sol in which the solvent was substituted with the ethanol with the addition of 0.1 mol HNO3, the coated glass showed the minimum value of the refractive index of 1.464, light transmittance of 94.2% at 550nm standard wavelength which is 3.2% higher than that of the parent glass, and the reflectance in the entire wave range of visible light. The refractive index represented its minimum at the sol concentration of 1.0 mol per 100mols of water and the higher the sol concentration, the higher the refractive index, resulting in the decrease of the light transmitance. The production condition of the reproducible anti-reflective coating on glass with the maximum transmittance of 94.2% was 4cm/min of withdrawal speed, 40$0^{\circ}C$ and 1 hour of heat treatment temperature and time, resulting in the film thickness of 94nm.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.73-79
• /
• 1999

The superstructured $Li_{4/3}Ti_{5/3}O_4$ was prepared by sol-gel process using a mixed solution of lithium acetate (LA) and titanium n-butoxide (TNB). The gel phase was obtained by adding ammonia water ($NH_4OH/TNB$ mole ratio of 0.35) and water ($H_2O/TNH$ mole ratio of 3.5) into the clear sol that was prepared after mixing TNB/LA mole ratio of 5/4 with AA/TNB mole raio of 0.125. It was found that the most suitable $Li_{4/3}Ti_{5/3}O_4$ was obtained by heat treatment of xerogel at $600^{\circ}C$ for 30 hrs. The synthesized $Li_{4/3}Ti_{5/3}O_4$ showed an initial discharge capacity of 174 mAh/g and the capacity loss of about 27.3% during 25 cycles in Li/1M $LiClO_4(in\;PC)/Li_{4/3}Ti_{5/3}O_4$ at current density of $0.15mA/cm^2$ and the voltage range of 0.5~3.0 V.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.676-681
• /
• 2001

ABS is a safety device, which adds hydraulic system to the existing brake system to prevent wheel from locking, so we can obtain maximum braking force on driving. The hydraulic system to control braking pressure consists of sol-flow type using solenoid valve, flow control valve or consists of sol-sol type using two solenoid valve. In this paper, the hydraulic system in ABS is composed of sol type using a 3port-2position solenoid valve, and vehicle system is composed of 1/4 vehicle model. And slip ratio is controlled using PWM (Pulse-Width-Modulation) control algorithm. Braking friction coefficient and tracking friction coefficient which are described by slip ratio's function have maximum value when slip ratio has its value from 0.1 to 0.3. And slip ratio is controlled constantly in this boundary value even in the variation of road's condition in some boundary.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.2
• /
• pp.103-109
• /
• 2011

Nanocrystalline $LiFePO_4$ powders were prepared at 660-$670^{\circ}C$ in an Ar atmosphere using two different synthetic routes, solid-state and sol-gel. Both materials showed well-developed XRD patterns without any impurity peaks. Particles composed in the range of 200-300 nm from the solid-state method, and 50-100 nm from the sol-gel method, were confirmed through scanning electron microscopy and dynamic light scattering. The $LiFePO_4$ obtained by the sol-gel method offered a high discharge capacity (153 mAh/g) and stable discharge behavior, even at elevated temperatures (50 and $60^{\circ}C$), whereas poor electrochemical performance was observed from the solid-state method. Rate capability studies for sol gel-derived $LiFePO_4$ ranged from 0.2 to 30 C, which revealed excellent retention over 70 cycles with a 99.9% capacity.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.66-71
• /
• 2015

$NaY_{1-x}(WO_4)_2:Ho^{3+}/Yb^{3+}$ phosphors with doping concentrations of $Ho^{3+}$ and $Yb^{3+}$ ($x=Ho^{3+}+Yb^{3+}$, $Ho^{3+}=0.05$, 0.1, 0.2, and $Yb^{3+}=0.2$, 0.45) were successfully synthesized via the cyclic microwave-modified sol-gel route; their upconversion properties were investigated. Well-crystallized particles showed a fine and homogeneous morphology with particle sizes of $2-5{\mu}m$. Under excitation at 980 nm, the synthesized particles exhibited yellow emissions based on a strong 550-nm emission band in the green region and a very strong 655-nm emission band in the red region. The Raman spectra of the doped particles indicated the domination of strong peaks at higher and lower frequencies induced by the incorporation of the $Ho^{3+}$ and $Yb^{3+}$ elements into the $Y^{3+}$ sites in the crystal lattice, which resulted in unit cell shrinkage that accompanied a new phase formation of the $WO_{4-x}$ group.

• Korean Journal of Materials Research
• /
• v.26 no.1
• /
• pp.29-34
• /
• 2016

$NaLa_{1-x}{(MoO_4)}_2$:$Ho^{3+}/Yb^{3+}$ phosphors with the correct doping concentrations of $Ho^{3+}$ and $Yb^{3+}$ ($x=Ho^{3+}+Yb^{3+}$, $Ho^{3+}=0.05$ and $Yb^{3+}=0.35$, 0.40, 0.45 and 0.50) were successfully synthesized by the microwave-modified sol-gel method. Well-crystallized particles formed after heat-treatment at $900^{\circ}C$ for 16 h showed a fine and homogeneous morphology with particle sizes of $3-5{\mu}m$. The optical properties were examined using photoluminescence emission and Raman spectroscopy. Under excitation at 980 nm, the UC intensities of the doped samples exhibited strong yellow emissions based on the combination of strong emission bands at 545-nm and 655-nm emission bands in green and red spectral regions, respectively. The strong 545-nm emission band in the green region corresponds to the $^5S_2/^5F_4{\rightarrow}^5I_8$ transition in $Ho^{3+}$ ions, while the strong emission 655-nm band in the red region appears due to the $^5F_5{\rightarrow}^5I_8$ transition in $Ho^{3+}$ ions. Pump power dependence and Commission Internationale de L'Eclairage chromaticity of the upconversion emission intensity were evaluated in detail.

• Korean Journal of Materials Research
• /
• v.26 no.12
• /
• pp.757-763
• /
• 2016

$Ho^{3+}/Yb^{3+}/Tm^{3+}$ tri-doped $NaY_{1-x}(WO_4)_2$ phosphors with proper doping concentrations of $Ho^{3+}$, $Yb^{3+}$ and $Tm^{3+}$ ($x=Ho^{3+}+Yb^{3+}+Tm^{3+}$, $Ho^{3+}$=0.04, 0.03, 0.02, 0.01, $Yb^{3+}$=0.35, 0.40, 0.45, 0.50 and $Tm^{3+}$=0.01, 0.02, 0.03, 0.04) were successfully synthesized via the microwave sol-gel route, and their upconversion properties were investigated. Well-crystallized microcrystalline particles showed fine and homogeneous microcrystalline morphology with particle sizes of $1-2{\mu}m$. The optical properties were comparatively examined using photoluminescence emission and Raman spectroscopy. Under excitation at 980 nm, the doped particles exhibited white emissions based on blue, green and red emission bands, which correspond to the $^1G_4{\rightarrow}^3H_6$ transitions of $Tm^{3+}$ in the blue region, the $^5S_2/^5F_4{\rightarrow}^5I_8$ transitions of $Ho^{3+}$ in the green region, the $^5F_5{\rightarrow}^5I_8$ transitions of $Ho^{3+}$, and the $^1G_4{\rightarrow}^3F_4$ and $^3H_4{\rightarrow}^3H_6$ transitions of $Tm^{3+}$ in the red region. The pump power dependence of the upconversion emission intensity and the Commission Internationale de L'Eclairage chromaticity coordinates of the phosphors were evaluated in detail.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.168-172
• /
• 2001

Co-Zn ferrite thin films grown on thermally oxidized silicon wafers were fabricated by a sol-gel method. Magnetic and structural properties of Co-Zn thin films were investigated by using x-ray diffractometer (XRD), atomic force microscopy (AFM), auger electron spectroscopy (AES) and a vibrating sample magnetometer (VSM). Co-Zn ferrite thin films annealed at 400 $^{\circ}C$ presented have only a single phase spinel structure without any preferred crystallite orientation. Their surface roughness of Co-Zn ferrite thin films was shown as less than 3 nm and the grain size was about 40 nm for annealing temperatures over 600 $^{\circ}C$. A moderate saturation magnetization of Co-Zn ferrite thin films for recording media was obtained in this study and there is no significant difference of their magnetic property with those external fields of parallel and perpendicular to planes of the films. The maximum value of the coercivity was obtained as 1,900 Oe for Co-Zn ferrite thin film annealed at 600 $^{\circ}C$.