• 한국표면공학회지
• /
• 제31권3호
• /
• pp.157-164
• /
• 1998

Effects of alloying elements on the pitting behavior of Ti-Al intermetalic compounds in the electrolytic soution containing Cl- were investigated through electrochemical tets and corrosion morphologies. Corrosion potential increased in the case of Cr addition to Ti-48%Al, whereas it decreased in the case of Si and B addition. The simultaneous addition of Cr and Si increased passive current density and decrosion corrosion potential. The passive current density of N addtion was higher than that of B addition in H2SO4 solution. With the addition of alloying elements, The pitting resistance decreased in order of TiAl>TiAlSi>TiAlN>TiAlB>TiAlCr and whin siumultaneous addition, it decreased in order of TiAlCrSi>TiAlCrBN>TiAlCrrN. The surface merohology after pitting test showed that the TiAl coataining Si had for fewer pits than that containing Cr and N simultaneously.

• 한국세라믹학회지
• /
• 제35권11호
• /
• pp.1130-1140
• /
• 1998

Thin films of $Bi_4Ti_3O_{12}\;nBaTiO_3(n=1&2)$ were prepared using sols erived Ba-Bi-Ti complex alkoxides. The sols were spin-cast onto $Pt/Ti/SiO_2/Si$ substrates and followed by pyrolysis for 1 hr at $620^{\circ}C,\;700^{\circ}C\;and\;750^{\circ}C$ In the thin films a pyrochlore phase seemed to be formed at a lower temperature and then tran-formed to the layered perovskite phase as the heating temperature increased. In the thin films pyrolyzed at formed to the layered perovskte phase as the heating temperature increased. In the films pyrolyzed at $750^{\circ}C$ the amount of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ reached to 94% while $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ was 77% in composition. This result shows that the formation of the layered pervoskite phase becomes difficult as the amount of complexing $BaTiO_3$ increases. The microstructures and the electrical properties of the thin films were gen-erally improved with the incease of the heating temperature. However the presence of the pyrochlore phase could not be removed effectively. Our study showed that the electrical properties of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ were pronouncedly improved with complexing with BaTiO3 when compared to those of $Bi_4Ti_3O_{12}$ while the presence of the pyrochlore phase was detrimental to the those of $Bi_4Ti_3O_{12}{\cdot}2BaTiO_3$.

• 한국진공학회지
• /
• 제7권2호
• /
• pp.141-149
• /
• 1998

$Si_3N_4$상에 PECVD법으로 W박막을 증착하였다. 기판온도와 소스가스의 유량비가 텅 스텐 박막에 미치는 영향을 조사하였다. $150^{\circ}C$~$250^{\circ}C$의 온도 범위 내에서 텅스텐 박막의 증착은 표면반응에 의하여 제한 되었으며, 기판온도와 $SiH_4/WF_6$ 유량비 변화에 따라 150~ 530$\AA$/min의 증착률과 스트레스에 영향을 주었고, 특히 과도한 Si3N4가스는 W박막의 구조, 화학적 결합, 스트레스등을 급격히 변화시켰다. TiN, Ti, Mo, NiCr, Al 등 여러 가지 부착층 상의 텅스텐 박막을 증착시킨 결과, Al이 가장 좋은 부착특성을 보였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.17-17
• /
• 2000

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.96-97
• /
• 1999

• 전자공학회논문지A
• /
• 제30A권10호
• /
• pp.59-66
• /
• 1993

PZT thin film deposited by rf magnetron sputtering was annealed by rapid thermal process(RTP) in PbO ambient to prevent vaporing of Pb and interface reactions. Si and TiN/Ti/Si substrates were prepared to survey application of TiN/Ti layer which can prevent interface interaction with Si and crack of PZT thin films. As temperature increased. PZT thin films surface on Si substrate appeared more severe cracks which should affect electrical properties deadly. TiN/Ti(40-150${\mu}{\Omega}{\cdot}cm$) layer applied for buffer layer suppressed interface interaction and film cracking. The measured leakage current(LC) and breakdown voltage(BV) of PZT thin film on TiN/Ti/Si substrate annealed at 650$^{\circ}$C for 15 sec (thickness of 2500$\AA$) were 38 nA/cm2 and 3.5 MV/cm and dielectric constant was 310 at 1 MHz, and remanent polarization (Pr) and coercive field (Ec) were 6.4${\mu}C/cm^{2}$ and 0.2MV/cm at 60 Hz, respectively.

• 한국재료학회지
• /
• 제3권1호
• /
• pp.12-18
• /
• 1993

단결정 실리콘위에 스퍼터법으로 증착된 티타니움막을 급속가열로에서 고상반응에 의해 형성시킨 면저항 1.2 ohm/sq. 내외의 TiS$i_2$ 박막에 있어서 열안정성을 상부절연막의 유무 및 종류에 따라 조사하였다. 상부절연막은 상압 CVD로 증착한 USG(Undoped Silicate Glass, Si$i_2$) 막과 플라즈마 CVD법으로 증착한 PE-SiN(S$i_3$$N_4$)막을 사용했다. 열안정성 평가는 90$0^{\circ}C$에서 시간을 달리하여 TiS$i_2$막, PE-SiN막, USG막의 스트레스는 각각 1.3${\times}{10^{9}}$, 1.25 ${\times}{10^{10}}$, 2.26 ${\times}{10^{10}}$ dyne/c$m^2$의 인장응력을 나타내었다. 응집현상은 TiS$i_2$의 응집현상은 Nabarro-Herring 마이크로 크리프에 의한 원자의 확산관점에서 검토되었다.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.82-88
• /
• 2001

In order to fulfil the requirements of the various performance profiles of ceramic cutting tools, six different SiC-based ceramics have been fabricated by hot-pressing (SiC--${Si}_3 {N}_4$composites) or by hot-pressing and subsequent annealing (monolithic SiC and SiC-TiC composites). Correlation between the annealing time and the corresponding microstructure and the mechanical properties of resulting ceramics have been investigated. The grain size of both ${Si}_3 {N}_4$and SiC in SiC-${Si}_3 {N}_4$composites increased with the annealing time. Monolithic SiC has the highest hardness, SiC-TiC composite the highest toughness, and the SiC-${Si}_3 {N}_4$composite the highest strength among the ceramics investigated. The hardness of SiC-${Si}_3 {N}_4$composites was relatively independent of the grain size, but dependent on the sintered density. The cutting performance of the newly developed SiC-based ceramic cutting tools will be described in Part 2 of this paper.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.209-209
• /
• 2003

기계가공용으로 개발된 3성분계 Ti-Si-N 코팅막은 약 40㎬이상의 초고경도이며, 그 미세구조는 나노입자의 TiN결정과 비정질 Si$_3$N$_4$로 이루어져 있다. Ti-Si-N 코팅의 경도는 극소량 Si를 첨가함에 따라 급격히 증가하였으며, 7.7at%에서 약 45㎬이었다. 그 이상에서는 감소하였다. 본 연구는 Ti-Si-N 코팅에서 규소첨가에 따른 박막에 형성하는 질화규소 또는 규소의 특성을 조사하기 위하여 질화규소 박막을 제조하여 그 특성 및 기계적 성질을 조사하였다. 스퍼터링 방법으로 제조한 질화규소 박막의 표면 및 내부구조를 광학현미경, 주사전자현미경, 투과전자현미경 그리고 AFM으로, 정성 및 정량을 EPMA와 EDS로, 결정성을 박막 엑스선회 절분석기로, 화학 결합구조을 XPS으로 분석하였다. 그리고 나노인덴터를 이용하여 박막의 경도와 탄성계수를 조사하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권4호
• /
• pp.410-414
• /
• 2013

We report the wet etching of titanium nickel (TiNi) films for the production of nano-electro-mechanical (NEM) device. $SiO_2$ and $Si_3N_4$ have been selected as sacrificial layers of TiNi metal and etched with polyethylene glycol and hydrofluoric acid (HF) mixed solution. Volume percentage of HF are varied from 10% to 35% and the etch rate of the $SiO_2$, $Si_3N_4$ and TiNi are reported here. Within the various experiment results, 15% HF mixed polyethylene glycol solution show highest etch ratio between sacrificial layer and TiNi metal. Especially $Si_3N_4$ films shows high etch ratio with TiNi films. Wet etching results are measured with SEM inspection. Therefore, this experiment provides a novel method for TiNi in the nano-electro-mechanical device.