• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.157-162
• /
• 2010

Effect of starting SiC particle size on nitridation rate and flexural strength of $Si_3N_4$-bonded-SiC (SNBSC) ceramics was investigated by using SiC particles of different size (${\sim}200\;{\mu}m$, ${\sim}100\;{\mu}m$ and ${\sim}45\;{\mu}m$). The specimen prepared from smaller SiC particles resulted in higher nitridation rate after nitridation at $1450^{\circ}C$, owing to the lower packing density in green body. The flexural strength showed maxima after 1-h nitridation for all specimens and then decreased with prolonged nitridation because of local densification-induced pore coarsening. The specimen prepared from smaller SiC particles showed better flexural strength because of smaller pore size and partly higher nitridation rate in the specimen. A maximal flexural strength of 29 MPa was obtained in the specimen with a density of $2.04\;g{\cdot}cm^3$, which was prepared from $45\;{\mu}m$-SiC particles.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.155-159
• /
• 2002

This paper has studied to obtain the grinding characteristics and optimal grinding conditions of ceramics in the grinding with diamond wheel by Taguchi method. Feed rate was most important factor to the surface roughness. In the case of 4{Si_3}{N_4}$ and ${A1_2}{O_3}$, surface roughness value were small at 3m/min of feed rate. In the case of $ZrO_2$. surface roughness value was small at 4m/min of feed rate. Surface roughness have much influenced by major load for the :ii3N4 and $ZrO_2$. On the other hand, ${A1_2}{O_3}$ have more influenced by grain shedding of brittle fracture phenomenon. The major factors affecting the surface roughness and the optimum grinding conditions were obtained with minimum experiment using Taguchi method.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.318-324
• /
• 2012

Reaction-bonded silicon nitrides containing rare-earth oxide sintering additives were densified by gas pressure sintering. The sintering behavior, microstructure and mechanical properties of the resultant specimens were analyzed. For that purpose, $Lu_2O_3-SiO_2$ (US), $La_2O_3$-MgO (AM) and $Y_2O_3-Al_2O_3$ (YA) additive systems were selected. Among the tested compositions, densification of silicon nitride occurred at the lowest temperature when using the $La_2O_3$-MgO system. Since the $Lu_2O_3-SiO_2$ system has the highest melting temperature, full densification could not be achieved after sintering at $1950^{\circ}C$. However, the system had a reasonably high bending strength of 527 MPa at $1200^{\circ}C$ in air and a high fracture toughness of 9.2 $MPa{\cdot}m^{1/2}$. The $Y_2O_3-Al_2O_3$ system had the highest room temperature bending strength of 1.2 GPa.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.155-158
• /
• 2000

NMR study has been used for measuring precise quantity of the amorphous phase in the $Si_3N_4$powder. Care must be taken to allow the $^{29}$Si nuclear spin system to fully relax between pulses in order to make the signals proportional to the number of nuclei in each phase. $^{29}$Si MAS spectrum was decomposed into the three spectra of $\alpha$-, $\beta$-, and amorphous $Si_3N_4$assuming pseudo-Voigt function. Moreover, the Rietveld analysis of the powder X-ray diffraction data was performed to measure quantity of crystalline phases as $\alpha/\beta$ ratio.

• Journal of the Korean Ceramic Society
• /
• v.47 no.4
• /
• pp.290-295
• /
• 2010

This study has been focused on properties of mirror surface grinding technology by ELID(Electrolytic In-process Dressing) for structural ceramics using in high precision structural parts as like semi-conductor manufacturing processes. The experimental studies have been carried out to get mirror surface for grinding of structural ceramics, SiC, $Al_2O_3$ and AlN. Grinding process of the ceramics is carried out with varying mesh type, depth of cut and feed rate using diamond wheel. The machining result of the surface roughness and condition of ground surface, have been analyzed by use of surface roughness tester, SEM, AFM and three dimensional surface profiler measurement system.

• Journal of the Korean Ceramic Society
• /
• v.21 no.4
• /
• pp.361-365
• /
• 1984

This study has been carried out to sinter silicon nitride with additives and to show the effect of surface finishments on its strength and Weibull modulus which are two most important factors for its applications into structural ceramics. Silicon nitride was sintered with the additions of $Al_2O_3$ and $Y_2O_3$ under pressureless cond-ition. The optimum properties were obtained by sintering at 1, 75$0^{\circ}C$ for 3hrs under $N_2$ atmosphere and the strength showed 6, 500kg/$cm^2$ at room temperature and 3, 300kg/$cm^2$ at 120$0^{\circ}C$. The effects of surface treatment on the strength of sintered $Si_3N_4$ were studied and the results showed that fine surface treatment increased the strength by up to 50% The Weibull analysis showed that its modulus was increased with increasing fineness of surface finishments. It was concluded that the mechanical properties of sintered silicon nitride could be improved by fine surface grinding which implied the brittle-fracture nature of sintered silicon nitride.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.9
• /
• pp.957-962
• /
• 2009

Sialon was produced by hot-pressing the mixtures of $Si_3N_4$, AlN and $Y_2O_3$ powders. All fracture tests were performed on a three-point loading system with a 30 mm bending span. Fracture toughness and Vickers hardness of smooth specimen were average 7.05 $MPa{\cdot}m^{0.5}$ and Hv = 1580, respectively. Density of three kinds of specimens, smooth specimen, smooth and healed specimen, smooth with $SiO_2$ colloidal coating and healed specimen, had beyond 99 % of theoretical density. Bending strength of smooth healed specimens had high strength more than 1 GPa. Crack healed specimens recovered as strength as smooth specimen. That is, cracked specimen with $SiO_2$ colloidal coating on cracked part recovered strength by heat treatment, completely. Crack healing of $Si_3N_4$ composite ceramics had contributed glassy $SiO_2$ to strength recovery. Limiting high temperature for bending strength of heat treated smooth specimen for bending strength was about 1273 K.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1996.11a
• /
• pp.6-6
• /
• 1996

Ceramic based nanocomposite, in which nano-sized ceramics and metals were dispersed within matrix grains and/or at grain boundaries, were successfully fabricated in the ceramic/cerarnic and ceramic/metal composite systems such as $Al_2O_3$/SiC, $Al_2O_3$/$Si_3N_4$, MgO/SiC, mullite/SiC, $Si_3N_4/SiC, $Si_3N_4$/B, $Al_2O_3$/W, $Al_2O_3$/Mo, $Al_2O_3$/Ni and $ZrO_2$/Mo systems. In these systems, the ceramiclceramic composites were fabricated from homogeneously mixed powders, powders with thin coatings of the second phases and amorphous precursor composite powders by usual powder metallurgical methods. The ceramiclmetal nanocomposites were prepared by combination of H2 reduction of metal oxides in the early stage of sinterings and usual powder metallurgical processes. The transmission electron microscopic observation for the $Al_2O_3$/SiC nanocomposite indicated that the second phases less than 70nm were mainly located within matrix grains and the larger particles were dispersed at the grain boundaries. The similar observation was also identified for other cerarnic/ceramic and ceramiclmetal nanocornposites. The striking findings in these nanocomposites were that mechanical properties were significantly improved by the nano-sized dispersion from 5 to 10 vol% even at high temperatures. For example, the improvement in hcture strength by 2 to 5 times and in creep resistance by 2 to 4 orders was observed not only for the ceramidceramic nanocomposites but also for the ceramiclmetal nanocomposites with only 5~01%se cond phase. The newly developed silicon nitride/boron nitride nanocomposites, in which nano-sized hexagonal BN particulates with low Young's modulus and fracture strength were dispersed mainly within matrix grains, gave also the strong improvement in fracture strength and thermal shock fracture resistance. In presentation, the process-rnicro/nanostructure-properties relationship will be presented in detail. The special emphasis will be placed on the understanding of the roles of nano-sized dispersions on mechanical properties.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.142-147
• /
• 1999

The interaction between commercial $Si_3N_4$ powder and two types of additives (nitrate and oxide additives) during the sintering of $Si_3N_4$ was investigated. The nitrates solution or oxide particles were added as a sintering additives. The surface of mixed powder was observed with FT-IR, TG, and HREM. DTA was used to characterize the reactivity of the powders. The formation of crystalline phases and phase transformation were analyzed by XRD. The adsorption of the additives on the surface of silicon nitride was confirmed in the nitrate salts. It was shown that the adsorption occurred by interaction between the amorphous $SiO_2$ layer on the $Si_3N_4$ surface and metal cations $(Al^{3++\; and \;Y^{3+})$ and anions $(NO_3\;^-\; or\; OH^-)$, resulting in a higher degree of homogeneous distribution of additives.

• Journal of the Korean Ceramic Society
• /
• v.20 no.1
• /
• pp.63-69
• /
• 1983

It is know that $Si_3-N_4$ bonded SiC has almost all the valuable properties needed for the high temperature material and thus has bery wide range of applicability. Si powder and two different sized SiC powder were used as the raw mateials. Specimens were prepared by heating the green compact mode of the raw materials with polyvinyl alcohol binder in the nitrogen atmosphere. The bond-ing of SiC particles is brought about with the formation of reaction bonded silicon nitride phase between the particles he influences of the variation of the relative amounts of the raw materials and the amount of the organic binder on the density and the bend strength of the specimens were investigated. It was shown that the calculation of the amount of the nitridation of Si is somewhat complicated matter since some portion of the organic binder reacts with the Si during the firing process. Fixing the Si amount to 20w/o the distributions of the size of the SiC particles that gives the maximum density and the maximum strnegth were obtained through experiments. It was observed that the two distributions were not equal to each other. As the amount of Si increased the amount of Si reacted with nitrogen and the strength increased. The fracture mode was intergranular for the most part and the transgranular fracture was scarcely observed.