• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.7
• /
• pp.1-6
• /
• 2000

In this study, the effects of the addition of $N_2$ gas into the $Cl_2$ (90)/Ar(10) gas mixture, which has been proposed as the optimized etching gas combination, for etching of platinum was performed. The selectivity of platinum film to $SiO_2$ film etch mask increased with the addition of $N_2$ gas, and etch profile over 75 $^{\circ}$ could be obtained when 20 % additive $N_2$ gas was added. These phenomena were interpreted as the results of a formation of blocking layer such as Si-N or Si-O-N on the $SiO_2$ mask. The maximum etch rate of Pt film and selectivity of Pt to $SiO_2$ are 1425 ${\AA}$/min and 1.71, respectively. These improvements were considered to be due to the formation of more volatile compounds such as Pt-N or Pt-N-Cl.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.12
• /
• pp.1366-1370
• /
• 2001

Thin films of the SiO2-TiO2-PDMS composite material have been prepared by the sol-gel dip coating method. Acid catalyzed solutions of tetraethoxy silane (TEOS) and polydimethyl siloxane (PDMS) mixed with titanium isopropoxide Ti(OiPr) were used as precursors. The optical and structural properties of the organically modified 70SiO2-30TiO2 composite films have been investigated with Fourier Transform Infrared Spectroscopy (FT-IR), UV-Visible Spectroscopy (UV-Vis), Differential Thermal Analysis (DTA) and prism coupling technique. The films coated on the soda-lime-silicate glass exhibit 450-750 nm thickness, 1.56-1.68 refractive index and 88-94% transmittance depending on the experimental parameters such as amount of PDMS, thermal treatment and heating rate. The optical loss of prepared composite film was measured to be about 0.34 dB/cm.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.161-168
• /
• 1996

For the improvement of microelectronic thin film interconnection materials, dielectric passivation effects on the electromigration phenomena were studied. Using Al-1%Si, various shaped patterns were fabricated and dielectric passivation layers of several structures were deposited on the $SiO_2$ layer. Lifetime of straight pattern showed 2~5 times longer than the other patterns that had various line width and area. It is believed that the flux divergence due to the structural inhomogeneity and so the current crowding effects shorten the lifetime of thin film interconnections. The lifetime of thin film interconnections seems to depend on both the passivation materials and the passivation thickness. PSG/$SiO_2$ dielectric passivation layers showed longer lifetime than $Si_3N_4$ dielectric passivation layers. This results from the PSG on $SiO_2$ layer reduces stress and from the improvement of resistance to the moisture and to the mobile ion such as sodium. This is also believed that the lifetime of thin film interconnections seems to depend on the passivation thickness in case of the same deposition materials.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.758-762
• /
• 2018

The transfer characteristics of zinc tin oxide(ZTO) on silicon dioxide($SiO_2$) thin film transistor generally depend on the electrical properties of gate insulators. $SiO_2$ thin films are prepared with argon gas flow rates of 25 sccm and 30 sccm. The rate of ionization of $SiO_2$(25 sccm) decreases more than that of $SiO_2$(30 sccm), and then the generation of electrons decreases and the conductivity of $SiO_2$(25 sccm) is low. Relatively, the conductivity of $SiO_2$(30 sccm) increases because of the high rate of ionization of argon gases. Therefore, the insulating performance of $SiO_2$(25 sccm) is superior to that of $SiO_2$(30 sccm) because of the high potential barrier of $SiO_2$(25 sccm). The $ZTO/SiO_2$ transistors are prepared to research the $CO_2$ gas sensitivity. The stability of the transistor of $ZTO/SiO_2$(25 sccm) as a high insulator is superior owing to the high potential barrier. It is confirmed that the electrical properties of the insulator in transistor devices is an important factor to detect gases.

• Journal of the Optical Society of Korea
• /
• v.18 no.1
• /
• pp.45-49
• /
• 2014

Well-crystallized $BaSi_2O_5:Eu^{2+}$ phosphor films were synthesized by heat treatment of spin-coated BaO:Eu on $SiO_2$ glass. We investigated luminescence-structure properties of these phosphor films as a function of heat-treatment temperature. From x-ray diffraction patterns, our $BaSi_2O_5:Eu^{2+}$ phosphor films revealed that (111)- and (204)-crystal planes of $BaSi_2O_5$ crystal were dominantly increased with an increase of heat-treatment temperature. Photoluminescence intensities of $BaSi_2O_5:Eu^{2+}$ phosphor films were increased with amount of these crystal planes. It can be explained that $Eu^{2+}$ ions were stably occupied at specific crystal orientation of $BaSi_2O_5$ crystal, enhancing the luminescent intensities of $BaSi_2O_5:Eu^{2+}$ phosphor films. In addition, our $BaSi_2O_5:Eu^{2+}$ phosphor films had transmittance of 70% at 510 nm,.due to the dense morphology and specific crystallinity of $BaSi_2O_5:Eu^{2+}$ phosphor films.

• Electrical & Electronic Materials
• /
• v.7 no.6
• /
• pp.481-489
• /
• 1994

The $SnO_2$/(n)Si solar cell was fabricated by electron beam evaporation method, and their properties were investigated. In proportion to increase of substrate and annealing temperature, the conductivity of $SnO_2$ thin film was increased, but its optical transmission decreases because of increasing optical absorption of free electrons in the thin film. $SnO_2$/Si Solar cell characteristics were improved by annealing, but the solar cells was deteriorated by heat treatment above 500[.deg. C]. The optimal outputs of $SnO_2$/Si solar cell through above investigations were $V_{\var}$:350[mV], $J_{sc}$ ;16.53[mA/c $m^{2}$], FF;0.41, .eta.=4.74[%]

• Journal of information and communication convergence engineering
• /
• v.1 no.3
• /
• pp.133-138
• /
• 2003

The preparation of $Al_{2}O_{3}-SiO_{2}$ thin films from less than one micron to several tens of microns in thickness had been prepared from metal alkoxide sols. Two methods, dip-withdrawal and electrophoretic deposition, were employed for thin films and sheets formation. The requirements to be satisfied by the solution for preparing uniform and strong films and by the factors affecting thickness and other properties of the films were examined. For the preparation of thin, continuous $Al_{2}O_{3}-SiO_{2}$ films, therefore, metal-organic-derived precursor solutions contained Si and Al in a chemically polymerized form has been developed and produced in a clear liquid state. In the process of applying to substrates, this liquid left a transparent, continuous film that could be converted to crystalline $Al_{2}O_{3}-SiO_{2}$ upon heating to $1000^{\circ}C$. And, a significant change of the film density took place in the crystallization process, thus leading to the strict requirements as to the film thickness, which could survive crystallization.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.957-962
• /
• 2003

The preparation of $Al_2$O$_3$-SiO$_2$ thin films from less than one micron to several tens of microns in thickness had been prepared from metal alkoxide sols. Two methods, dip-withdrawal and electrophoretic deposition, were employed for thin films and sheets formation. The requirements to be satisfied by the solution for preparing uniform and strong films and by the factors affecting thickness and other properties of the films were examined. for the preparation of thin, continuous $Al_2$O$_3$-SiO$_2$ films, therefore, metal-organic-derived precursor solutions contained Si and Al in a chemically polymerized form has been developed and produced in a clear liquid state. In the process of applying to substrates, this liquid left a transparent, continuous film that could be converted to crystalline $Al_2$O$_3$-SiO$_2$ upon heating to 100$0^{\circ}C$. And, a significant change of the film density took place in the crystallization process, thus leading to the strict requirements as to the film thickness, which could survive crystallization.

• Journal of the Korean Ceramic Society
• /
• v.30 no.8
• /
• pp.615-622
• /
• 1993

In order to increase chemical durability of thin films in binary system B2O3-SiO2 and Al2O3-SiO2 on the slide glass by the dip-coating technique from TEOS(Tetraethyl Orthosilicate) and boric acid or aluminum nitrate, phosphoric acid(5~20mol%) was added, respectively. Corrosion of acid and alkali of samples treated with 1N, HCl, NaOH and distilled water at 10$0^{\circ}C$ for 15 minute, were measured IR transmittance and variance of transmittance at visible range. Surface structure of thin film was investigated with SEM and formation of crystal phase according to additiion of phosphoric acid was measrued with XRD. In Al2O3-SiO2 system, change of remarkable characteristic was not obtained at the addition of P2O5 but transmittance of thin film was decreased with addition of P2O5 in B2O3-SiO2 system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.509-512
• /
• 1999

Ferroelectric Sr$_2$(Nb, Ta)$_2$O$_{7}$(SNTO), La$_2$Ti$_2$O$_{7}$(LTO) thin films were prepared by sol-gel processes. SNTO, LTO thin films were spin-coated on Pt/TiO$_2$/SiO$_2$/Si(100). Pt/Ti/SiO$_2$/Si(100). PT/ZrO$_2$/SiO$_2$/Si(100) substrates. After multiple coating, dried thin films were heat-treated for decomposition of residual organics and crystallization. Dielectric and other relevant electrical properties were measured and the results showed a little possibility in ferroelectric gate random access memory devices.ces.