• Journal of the Korean Chemical Society
• /
• v.9 no.4
• /
• pp.179-184
• /
• 1965

Korean acid clays and Japanese acid clay were 1 N KCl solution and then their acidities were determined by measuring pH of the filtrates produced. And on examining the effect of neutral salt solution, such as KCl, NaCl, $BaCl_2,\;Pb(NO_3)_2\;and\;CuSO_4$, on the acidity, it was found that the effect decreased in order mentioned above and this situation proved to be in accord with Lyotrope series, i.e., the order of $K^+>Na^+>Ba^{++}>Pb^{++}>Cu^{++}.$ And after adsorbing cation, $Al_2O_3\;and\;Fe_2O_3$ which dissolved out of acid clay were measured, with the result that the amounts dissolved out were nearly proportional to acidity. This result accords with Kobayashi and Yamamoto's theory that the cause for acidity of clays is due to the fact that HCl which is formed initially by exchange of cation reacts with solid clay, and then chlorides dissolved out bring about hydrolysis, then resulting in the second formation of HCl. On measuring the rate which acid clay adsorbed dye in aqueous solution of basic and acid dyes, it was found that acid dye had no relation to acidity, and though it was not adsorbed by acid clay, the adsorption rate of basic dye was proportional to acidity. After adsorbing basic dye, pH was proportional to both acidity of solid acid and its adsorption rate of dye. Hence, it was concluded that the adsorption of basic dye was in accord with adsorption mechanism of neutral salt. This study led to find the acidic cause of solid acid and its adsorption mechanism of dye in aqueous solution.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.3
• /
• pp.131-142
• /
• 2002

The Langmuir adsorption isotherms of the under-potentially deposited hydrogen (UPD H) and the over-potentially deposited hydrogen (OPD H) at the poly-Pt/0.5M $H_2SO_4$ and 0.5 M LiOH aqueous electrolyte interfaces have been studied using cyclic voltammetric and ac impedance techniques. The behavior of the phase shift $(0^{\circ}{\leq}{-\phi}{\leq}90^{\circ})$ for the optimum intermediate frequency corresponds well to that of the fractional surface coverage $(1{\geq}{\theta}{\geq}0)$ at the interfaces. The phase-shift method, i.e., the phase-shift profile $({-\phi}\;vs.\;E)$ for the optimum intermediate frequency, can be used as a new electrochemical method to determine the Langmuir adsorption isotherms $({\theta}\;vs.\;E)$ of the UPD H and the OPD H for the cathodic $H_2$ evolution reactions at the interfaces. At the poly-Pt/0.5M $H_2SO_4$ aqueous electrolyte interface, the equilibrium constant (K) and the standard free energy $({\Delta}G_{ads})$ of the OPD H are $2.1\times10^{-4}$ and 21.0kJ/mol, respectively. At the poly-Pt/0.5M LiOH aqueous electrolyte interface, K transits from 2.7(UPD H) to $6.2\times10^{-6}$ (OPD H) depending on the cathode potential (E) and vice versa. Similarly, ${\Delta}G_{ads}$ transits from -2.5kJ/mol (UPD H) to 29.7kJ/mol (OPD H) depending on I and vice versa. The transition of K and ${\Delta}G_{ads}$ is attributed to the two distinct adsorption sites of the UPD H and the OPD H on the poly-Pt surface. The UPD H and the OPD H on the poly-Pt surface are the independent processes depending on the H adsorption sites themselves rather than the sequential processes for the cathodic $H_2$ evolution reactions. The criterion of the UPD H and the OPD H is the H adsorption sites and processes rather than the $H_2$ evolution reactions and potentials. The poly-Pt wire electrode is more efficient and useful than the Pt(100) disc electrode for the cathodic $H_2$ evolution reactions in the aqueous electrolytes. The phase-shift method is well complementary to the thermodynamic method rather than conflicting.

• Journal of the Korean Chemical Society
• /
• v.64 no.6
• /
• pp.334-344
• /
• 2020

The adsorption of various atmospheric harmful gases (COx, NOx, SOx) on graphene-like Germanene 2D sheet was theoretically investigated using density functional theory(DFT) method. The structures were fully optimized at the B3LYP/cc-pvDZ and CAM-B3LYP/cc-pvDZ levels of theory and confirmed to be a local minimum by the calculation of the harmonic vibrational frequencies. The adsorptions of gases on the Germanene sheet were predicted to be a physisorption process for CO, CO2, NO, and SO2 gases but to be a chemisorption process for NO2, SO, and SO2 gases.

• Resources Recycling
• /
• v.20 no.6
• /
• pp.28-36
• /
• 2011

The adsorption of nickel(Ni) from sulfuric acid solution was carried out by ion exchange method. A series of batch tests in synthetic solutions were carried out using Lewatit Monoplus TP 220 resin. The following experimental parameters, such as temperature, shaking rate, reaction time, pH, resin dosage and concentration of nickel ions etc. were investigated to establish the effective optimum conditions of nickel adsorption. The solution pH(2.0~5.0) and shaking rate had little effects on the adsorption of nickel and adsorption time of 72hours was required to reach equilibrium. The experimental results show a good agreement with Feundlich isotherm and pseudo-second order reaction. The adsorption behavior of Ni obtained from synthetic solution was compared with that of waste electroplating solution. Elution of nickel from loaded resin increased with increase in $H_2SO_4$ concentration.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.230-235
• /
• 2005

Reversed-phase high-performance liquid chromatography (RP-HPLC) was used to determine the equilibrium isotherm of single and multi-components of dUrd(2'-deoxyuridine), dGuo(2'-deoxyguanosine), and dAdo(2'-deoxyadenosine) of 2'-deoxyribonucleosides by dynamic method. The composition of mobile phase was 90/10 vol.% (water/MeOH). With an increase in the injection volumes, the retention times were shorter and the peak shapes were triangle-shaped, so Langmuir-type isotherm was assumed. The Langmuir adsorption parameters were estimated by PIM (pulsed-input method), and the competitive Langmuir adsorption isotherm was further utilized. For the sample of the dUrd and dGuo whose retention times were relatively short, the agreement of between the calculated value and experimental data was fairly good in both single and multi-components, but for the dAdo, the last eluting component, some deviations were caused by non-linear and non-ideal properties.

• Carbon letters
• /
• v.3 no.4
• /
• pp.198-204
• /
• 2002

In this paper, impregnated activated carbon fiber (IACF) was manufactured to pitch-based activated carbon fibers (ACF) with potassium hydroxide (KOH) by using wet impregnation method to raise nitrogen oxides ($NO_x$) adsorptivity. The properties of IACF were observed using EPMA, TGA and DSC and $NO_x$ adsorptivity was observed at high and low temperature. Before and after adsorption was analyzed using ToF-SIMS for examine surface characterization of adsorbed $NO_x$. The results showed that the better adsorptivity appeared for increasing KOH ratio. So, $NO_x$ adsorptivity showed result that is proportional between KOH and the adsorbed amount. On the other hand, adsorbent that manufactured without washing was better $NO_x$ adsorptivity than adsorbent that manufactured with washing. The behavior of adsorption show that crossing time of NO and $NO_2$ delayed for a rising adsorptivity. And NO ratio increased but $NO_2$ ratio decreased according as KOH ratio increases. $NO_x$ was confirmed through surface analysis that remain in $NO_2^-$ and $NO_3^-$ form on IACF surface.

• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.92-97
• /
• 1998

Malodorous gases give discomfort and harm to laborers and residential neighborhoods and therefore, the removing odor materials emitted from plants and industrial facilities is important subject. The main ingredients of alkali odor are $NH_3$ and $CE_3SH$. The adsorption characteristics of odors were studied using four different activated carbon fibers(ACF) and active carbon(AC). Alkali odor was removed by using ACF impregnated with $H_3PO_4$ and $H_2SO_4$ and treated with $HNO_3$ and NaOH. The experimental result showed that ACF has a higher removal efficiency than AC. The adsorption capacity was increased with the impregnation and surface treatment, and $H_2SO_4$ was the best impregnant for the removal of alkali odor.

• Economic and Environmental Geology
• /
• v.31 no.1
• /
• pp.11-20
• /
• 1998

The effects of the major cations ($Ca^{2+}$, $Mg^{2+}$, $K^+$, $Na^+$), complex-forming anions ($SO_4{^{2-}}$, $HCO_3{^-}$), and solution pH on the adsorption of $^{137}Cs$ and $^{90}Sr$ by kaolinite in groundwater chemistry were investigated. Three-dimensional Kd modelling designed by a statistical method was attempted to compare the relative effect among hydrated radii, charge and concentration of competing cations on the adsorption of Cs and Sr. The modelling results indicate that the hydrated radii of competing cations is the most important factor, and then their charges and concentrations are also important factors in order. The property of zeta potential of kaolinite particles was discussed in terms of the amphoteric reactions of a kaolinite surface affecting the adsorption of Cs and Sr. The ionic strength of competing cations on the adsorption of Cs and Sr exerts a greater effect than the solution pH. The sorption behaviour of Sr on kaolinite is also highly dependent on the concentration of bicarbonate. The speciation of Sr and the saturation state of a secondary phase were thermodynamically calculated by a computer program, WATEQ4F. This indicates that the change in solution pH with the concentration of bicarbonate and the precipitation of a strontianite ($SrCO_3$) are major factors controlling Sr adsorption behaviour in the presence of bicarbonate ion.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.2
• /
• pp.37-46
• /
• 2004

The electrochemical adsorption of the Ag ions from aqueous solution on pelletized activated carbon monolith was investigated over wide range of operation time. The adsorption capacities of pelletized activated carbon monolith are associated with their internal porosity and are related properties such as surface area, pore size distribution. The chemical industry generates wastewater that contains toxic matters like heavy metals in small concentrations so that their economic recovery is not feasible. But, the method using activated carbon monolith can be used to withdrawal of heavy metals in waste water. After the electrochemical treatment, the quantitative properties in Ag ion solutions are also examined by pH concentration and studied elemental analysis by ICP-Atomic Emission Spectrometer and Energy Disperse X-ray (EDX) spectra. It is consider that the pH is very important factor at the reason of water pollutant with increasing acidity in industrial field. The result of quantitative analysis using Inductively Coupled Plasma-Atomic Emission Spectrometer of metal after electrochemical reaction in Ag ions solution depending on time are shown that the amount of Ag ions deposited was decreased with growth of Ag particles on the carbon surfaces as increasing electrochemically treated time. And, surface morphologies are investigated by scanning electron microscopy (SEM) to explain the changes in adsorption properties.

• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.789-795
• /
• 2001

In order to recover nickel ion from waste water containing heavy metals, the PAN fibrous ion-exchanger with primary, secondary amine groups and carboxyl group was synthesized by acid and base hydrolysis. The hydrolysis yield of PAN fiber in acid solution was higher than base solution. The swelling ratio and ion-exchange capacity of PAN fiber which was synthesized in 1N $H_2SO_4$ solution at $80^{\circ}C$ for 7 hrs appeared 71.2% and 1.95 meq/g respectively. We investigated that the adsorption of nickel ion was approached 1.44 meq/g at 50 min and the maximum adsorption capacity of ion-exchanger was 2.48 meq/g. We confirmed that the $Ni^{+2}$ adsorption ability of the synthesized PAN fibrous ion-exchanger in this study is excellent.