• Tribology and Lubricants
• /
• v.32 no.2
• /
• pp.56-60
• /
• 2016

Sapphire has a high hardness and strength and chemical stability as a superior material. It is used mainly as a material for a semiconductor as well as LED. Recently, the cover glass industry used by a sapphire is getting a lot of attention. The sapphire substrate is manufactured through ingot sawing, lapping, diamond mechanical polishing (DMP) and chemical mechanical polishing (CMP) process. DMP is an important process to ensure the surface quality of several nm for CMP process as well as to determine the final form accuracy of the substrate. In DMP process, the material removal is achieved by using the mechanical energy of the relative motion to each other in the state that the diamond slurry is disposed between the sapphire substrate and the polishing platen. The polishing platen is one of the most important factors that determine the material removal characteristics in DMP. Especially, it is known that the geometric characteristics of the polishing platen affects the material removal amount and its distribution. This paper investigated the material removal characteristics and the effects of the polishing platen groove in sapphire DMP. The experiments were preliminarily carried out to evaluate the sapphire material removal characteristics according to process parameters such as pressure, relative velocity and so on. In the experiment, the monitoring apparatus was applied to analyze process phenomena in accordance with the processing conditions. From the experimental results, the correlation was analyzed among process parameters, polishing phenomena and the material removal characteristics. The material removal equation based on phenomenological factors could be derived. And the experiment was followed to investigate the effects of platen groove on material removal characteristics.

• Journal of Environmental Science International
• /
• v.12 no.9
• /
• pp.1017-1023
• /
• 2003

The high speed elimination process of suspended solid was investigated to treat the pulp waste water by using surface modified magnetite particle and magnetic power. The effects of the various aluminum salts such as Al(NO$_3$)$_3$ㆍ9$H_2O$, AlC1$_3$ㆍ6$H_2O$, $Al_2$(SO$_4$)$_3$ㆍ13∼14 on the COD, BOD and suspended solid were systematically studied. It has been found that the 2.0 wt% of Al was most effective for the modification of Fe$_3$O$_4$ powder and then best for the treatment of pulp waste water, Optimum quantity of modified magnetite in this study was 12 wt%, and aging time was found to be 12 hours. Comparing with the conventional process, the required time for SS removal was drastically decreased. BOB and COD were also effectively removed when applied to the pulp wastewater.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.479-488
• /
• 2011

Nanofiltration was performed with polyaluminium chloride solutions at different pH conditions to understand effects of inorganic compounds on aluminum hydrolysis products, i.e., three distinctive groups of aluminum species: polymeric Al at low pH; $Al(OH)_3$ at neutral pH; and ${Al(OH)_4}^-$ at high pH. The PACl solution was prepared to be approximately 4.0mM and adjusted to the designated pH. The influence of inorganic compounds on Al species fouling was investigated with 4.9mM $CaCl_2$ and 3.5mM $MgSO_4$ because $Ca^{2+}$, $Mg^{2+}$, $Cl^-$, ${SO_4}^{2-}$ are the most common inorganics in the drinking water. NF membrane fouling was measured by flux decline rate. The impact of $CaCl_2$ was not significant on the individual Al hydrolysis products fouling. However, the flux decline rate was drastically changed in the presence of $MgSO_4$. The concentration of particulate matters was considerably increased possibly due to interaction between Al species and ${SO_4}^{2-}$ where $MgSO_4$ was introduced. The particulates were accumulated on the membrane and enhanced the hydraulic resistance of the cake layer. In addition, conductivity removal of the membrane was decreased when Al-hydroxide was dominant due to reduction of membrane surface charge. The rejection of $Ca^{2+}$and $Mg^{2+}$ were considerably different, which implys that composition of inorganics paly a role on conductivity removal.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2010.04a
• /
• pp.608-609
• /
• 2010

• Membrane Journal
• /
• v.17 no.4
• /
• pp.302-310
• /
• 2007

The effects of various system parameter on the absorption of sulfur dioxide into the absorbent liquid were investigated in a circulatory porous polymer membrane contactor. A feed gas and an absorbent used in the study were the gas mixture of air and $SO_2$ and the $Na_2SO_3$ aqueous solution, respectively. The separation of sulfur dioxide was measured in terms of the concentration of $Na_2SO_3$ absorbent, the concentration of sulfur dioxide, the feed flow rate, the absorbent velocity and the different membrane material. As the concentration of absorbent increased from 0.05 to 0.2 M, the removal efficiency increased from 74 to 100%. By increasing the concentration of sulfur dioxide from 700 to 2,500 ppm, the removal efficiency decreased from 100 to 75%. Also as the absorbent velocity increased from 2.5 to 15 mL/min, the removal efficiency increased from 85 to 100%. As the porosity of the membrane increased, the removal efficiency increased.

• Textile Coloration and Finishing
• /
• v.22 no.2
• /
• pp.145-154
• /
• 2010

An alkalophilic microorganism capable of degrading dyes was developed for the treatment of alkaline dye solution. This strain was identified as Pseudomonas species. Using this microorganism, biological treatment of dye was studied in Erlenmeyer flasks. The characteristics of this microorganism were observed under various incubating-condition such as temperature, pH, nitrogen source, and macronutrients concentration. The removal effciencies of Disperse Red 60 from synthetic wastewater were 33.5 ~ 36.9% at the range of $30{\sim}40^{\circ}C$, and they were 31.1 ~ 36.7% at the range of initial pH 8 ~ pH 10, respectively. The optimal culture medium was found to be 0.25%(w/v) yeast extract, 0.25%(w/v) polypeptone, 0.1%(w/v) $KH_2PO_4$, 0.2%(w/v) $MgSO_4{\cdot}7H_2O$, and 1.0%(w/v) $Na_2CO_3$. In treatment of various dyes using Erlenmeyer flasks, the removal effciencies of Disperse Blue 87, Disperse Yellow 64, Disperse Red 60, Acid Blue 193, Acid Red 138, and Direct Yellow 23 were found to be 76%, 71%, 58%, 93%, 94%, and 90% respectively after 24hrs reaction of alkalophilic strain Pseudomonas sp. YBE-12.

• Clean Technology
• /
• v.20 no.1
• /
• pp.51-56
• /
• 2014

In this study, PSf-$Al(OH)_3$ beads were prepared by immobilizating aluminum hydroxide $Al(OH)_3$ with polysulfone (PSf). The removal experiments of the fluoride ions by PSf-$Al(OH)_3$ beads were conducted batchwise and the parameters such as pH, initial fluoride concentration, and coexisting ions were investigated. The maximum removal capacity obtained from Langmuir isotherm was 52.4 mg/g and the optimum pH region of fluoride ions was in the range of 4 to 10. The removal process of fluoride ions by PSf-$Al(OH)_3$ beads was found to be controlled by both external mass transfer at the earlier stage followed by internal diffusion at the later stage. The presence of coexisting anions such as $HCO_3{^-}$, $SO{_4}^{2-}$, $NO_3{^-}$, and $Cl^-$ had a negative effect on removal of fluoride ions by PSf-$Al(OH)_3$ beads.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.75-84
• /
• 2009

STATEMENT OF PROBLEM. A number of studies about the nano-treated surfaces of implants have been conducting along with micro-treated surfaces of implants. PURPOSE. The purpose of this study was to get information for the clinical use of nano-treated surfaces compared with micro-treated surfaces by measuring removal torque and analyzing histological characteristics after the placement of various surface-treated implants on femurs of dogs. MATERIAL AND METHODS. Machined surface implants were used as a control group. 4 nano-treated surface implants and 3 micro-treated surface implants [resorbable blast media surface (RBM), sandblast and acid-etched surface (SAE), anodized RBM surface] were used as experimental groups. Removal torque values of implants were measured respectively and the histological analyses were conducted on both 4weeks and 8weeks after implant surgery. The surfaces of removed implants after measuring removal torque values were observed by scanning electron microscopy (SEM) at 8 weeks. RESULTS. 1. Removal torque values of the nano-treated groups were lower than those of micro-treated groups. 2. Removal torque values were similar in the anodized RBM surface groups. 3. On the histological views, there was much of bone formation at 8 weeks, but there was no difference between 4 and 8 weeks, and between the types of implant surfaces as well. CONCLUSION. it is suggested that implant topography is more effective in removal torque test than surface chemistry. To get better clinical result, further studies should be fulfilled on the combined effect of surface topography and chemistry for the implant surface treatments.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.1
• /
• pp.53-62
• /
• 2014

In order to remove Fe impurity from low-grade pyrophyllite ore, the effect of certain variables such as particle size, concentration of sulfuric acid, amount of ammonium sulfate, added hydrogen peroxide, and temperature were studied. The euhedral cubic pyrites were observed in the low-grade pyrophyllite ore by reflected light microscopy, and quartz and dickite were identified in the sample by XRD analysis. The results of the Fe removal experiments showed that the best Fe removal parameters were when the particle size was at -325 mesh, the addition of $H_2SO_4$, $(NH_4)_2SO_4$ and $H_2O_2$ was at a 2.0 M, 10.0 g/l, and 3.0 M concentration, respectively, and at a $70^{\circ}C$ leaching temperature. In the dissolution kinetics analysis, the dissolution of Fe from the pyrite surface was a controlled chemical reaction, and the Fe dissolution reaction was proportioned to 0.066/R, $[H_2SO_4]^{1.156}$, $[(NH_4)_2SO_4]^{0.745}$, $[H_2O_2]^{0.428}$.

• Journal of environmental and Sanitary engineering
• /
• v.19 no.1
• /
• pp.37-41
• /
• 2004

The removal efficiency of cadmium by chitosan complex isolated from Aspersillus oryzae was investigated through laboratory experiments. The results of the study are as follows. The adsorption kinetics of cadmium was reached the adsorption equilibrium in approximately 20 minutes and the removal efficiency was showed 95.8%. The effect of temperature on cadmium adsorption by chitosan complex shows that as the temperature increased, the amount of cadmium adsorption per unit weight of chitosan complex increased. The correlation between amount of cadmium adsorption per unit weight of chitosan complex and temperature was obtained through the coefficient of determination($R^2$). $R^2$ values was 0.854(p<0.05). A linearized Freundlich equation was used to fit the acquired experimental data. As a result, Freundlich constant, the adsorption intensity(1/n) was 0.550, and the measure of adsorption(k) was 2.181. So, it was concluded that adsorption of cadmium by chitosan complex is effective.