• 청정기술
• /
• 제14권1호
• /
• pp.29-34
• /
• 2008

폴리올 주 사슬에 에스테르기를 도입하기 위한 방법으로 산화프로필렌 (propylene oxide, PO)과 무수 프탈산(phthalic anhydride, PA)의 공중합을 이중금속 시안염 촉매 존재 하에서 수행하였다. 이중금속 시안염 촉매는 이 공중합에 매우 효율적인 촉매임을 알 수 있었으며, 이 공중합에 대한 반응성비는 변형 Kelen $T{\ddot{u}}d{\ddot{o}}s$ 식을 이용하여 구한 결과 $r_1(PA)\;=\;0$, $r^2(PO)\;=\;0.248$이었다. 주 사슬에 함유되어 있는 PA의 함량이 1.0, 2.1, 7.52, 11.42 mol%인 4가지 폴리을 시료를 이용하여 경질부 함량이 19 wt%인 열가소성 폴리우레탄을 제조하였다. PA의 함량이 증가할수록 신율은 낮아졌으며, 인장강도와 인장탄성율은 증가하는 경향을 보였다. PO와 PA를 공중합 하여 폴리올에 도입되는 PA의 함량을 조절함으로써 결과적으로 폴리우레탄의 물성을 조절할 수 있음을 알 수 있었다.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3516-3525
• /
• 2022

The high capture cross-section (𝜎_c) of Gadolinium (Gd-155 and Gd-157) causes reactivity penalty and swing at the initial stage of fuel burnup in Pressurized Water Reactor (PWR). The present study is concerned with the feasibility of the combination of mixed burnable poison with both low and high 𝜎_c as an approach to minimize these effects. Two considered reference designs are fuel assemblies with 24 IBA rods of Gd₂O₃ and Er₂O₃ respectively. Models comprise nuclear fuel with a homogeneous mixture of Er₂O₃, AmO₂, SmO₂, and HfO₂ with Gd₂O₃ as well as the coating of PaO₂ and ZrB₂ on the Gd₂O₃ pellet's outer surface. The infinite multiplication factor was determined and reactivity was calculated considering 3% neutron leakage rate. All models except Er₂O₃ and SmO₂ showed expected results namely higher values of these parameters than the reference design of Gd₂O₃ at the early burnup period. The highest value was found for the model of PaO₂ and Gd₂O₃ followed by ZrB₂ and HfO₂. The cycle burnup, discharge burnup, and cycle length for three batch refueling were calculated using Linear Reactivity Model (LRM). The pin power distribution, energy-dependent neutron flux and Fuel Temperature Coefficient (FTC) were also studied. An optimization of model 1 was carried out to investigate effects of different isotopic compositions of Gd₂O₃ and absorber coating thickness.

• 한국결정성장학회지
• /
• 제32권3호
• /
• pp.103-106
• /
• 2022

소다석회유리에서 Al₂O₃가 isokom 온도에 미치는 영향을 Lakatos 모델을 이용하여 분석하였다. Na₂O와 CaO의 함량이 같고 SiO₂의 양이 0.5 mol% 감소하고 Al₂O₃ 양이 0.5 mol% 증가했을 때 isokom 온도는 log η = 12.3, 10, 6.6, 1에서 각각 3.1, 3.3, 3.6, 7.2℃ 높아졌다. 한편, SiO₂와 Na₂O의 함양이 같고 CaO가 0.5 mol% 감소하고 Al₂O₃가 0.5 mol% 증가한 경우는 log η = 12.3, 10, 6.6, 1에서 각각 1.6, 2.3, 4.1, 17.7℃ isokom 온도가 높아졌다.

• 한국지구과학회지
• /
• 제27권1호
• /
• pp.49-60
• /
• 2006

본 연구는 나주지역 하상퇴적물에 대한 지구화학적 특성 연구이다. 이를 위해 1차 수계를 대상으로 139개의 하상퇴적물 시료를 채취하였다. 채취된 시료는 실험실에서 자연 건조시켰으며, XRF, ICP-AES, NAA를 이용하여 화학분석을 실시하였다. 기반암에 따른 지구화학적 특성을 알아보기 위하여, 화강암질편마암 지역, 편암류 지역, 화강암류 지역, 사질암 지역, 응회암 지역, 안산암 지역, 유문암 지역으로 분류하였다. 나주지역 하상퇴적물의 지질집단별 주성분원소 평균함량은 $SiO_2\;58.37{\sim}66.06wt.%,\;Al_2O_3\;13.98{\sim}18.41wt.%,\;Fe_2O_3\;4.09{\sim}6.10wt.%,\;CaO\;0.54{\sim}1.33wt.%,\;MgO\;0.86{\sim}1.34wt.%,\;K_2O\;2.38{\sim}4.01wt.%,\;Na_2O\;0.90{\sim}1.32wt.%,\;TiO_2\;0.82{\sim}1.03wt.%,\;MnO\;0.09{\sim}0.15wt.%,\;P_2O_5\;0.11{\sim}0.18wt.%$이다. 주성분원소의 평균함량 비교에서 $Al_2O_3$와 $K_2O$는 화강암질편마암 지역에서, $Fe_2O_3,\;CaO,\;P_2O_5$는 응회암 지역에서, MgO와 $TiO_2$는 안산암 지역에서, $Na_2O$는 유문암 지역에서 높고, $SiO_2$와 MnO 함량은 사질암 지역에서 약간 높다. 미량성분 및 희토류원소의 지질집단별 평균함량은 $Ba\;1278{\sim}1469ppm,\;Be\;1.1{\sim}1.5ppm,\;Cu\;18{\sim}25ppm,\;Nb\;25{\sim}37ppm,\;Ni\;16{\sim}25ppm,\;Pb\;21{\sim}28ppm,\;Sr\;83{\sim}155ppm,\;V\;64{\sim}98ppm,\;Zr\;83{\sim}146ppm,\;Li\;32{\sim}45ppm,\;Co\;7.2{\sim}12.7ppm,\;Cr\;37{\sim}76ppm,\;Cs\;4.8{\sim}9.1ppm,\;Hf\;7.5{\sim}25ppm,\;Rb\;88{\sim}178ppm,\;Sc\;7.7{\sim}12.6ppm,\;Zn\;83{\sim}143ppm,\;Pa\;11.3{\sim}37ppm,\;Ce\;69{\sim}206ppm,\;Eu\;1.1{\sim}1.5ppm,\;Yb\;1.8{\sim}4.4ppm$이다. Pb, Li, Cs, Hf, Rb, Sb, Pa, Ce, Eu, Yb 평균함량은 화강암질편마암 지역에서, Ba, Co, Cr 평균함량은 편암류 지역에서, Nb, Ni, Zr 평균함량은 사질암 지역에서, Sr 평균함량은 응회암 지역에서 높고, Be, Cu, V, Sc, Zn 평균함량은 안산암 지역에서 다른 지질집단에서 보다 높다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.418.2-418.2
• /
• 2016

$Al_2O_3$ passivation layer has excellent passivation properties at p-type Si surface. This $Al_2O_3$ layer forms thin $SiO_2$ layer at the interface. There were some studies about inserting thermal oxidation process to replace naturally grown oxide during $Al_2O_3$ deposition. They showed improving passivation properties. However, thermal oxidation process has disadvantage of expensive equipment and difficult control of thin layer formation. Wet chemical oxidation has advantages of low cost and easy thin oxide formation. In this study, $Al_2O_3$/$SiO_2/Si(100)$ interface was formed by wet chemical oxidation and PA-ALD process. $SiO_2$ layer at Si wafer was formed by $HCl/H_2O_2$, $H_2SO_4/H_2O_2$ and $HNO_3$, respectively. 20nm $Al_2O_3$ layer on $SiO_2/Si$ was deposited by PA-ALD. This $Al_2O_3/SiO_2/Si(100)$ interface were characterized by capacitance-voltage characteristics and quasi-steady-state photoconductance decay method.

• Membrane and Water Treatment
• /
• 제14권3호
• /
• pp.129-140
• /
• 2023

The appropriate injection of H₂O₂ is essential to produce hydroxyl radicals (OH·) by mixing H₂O₂ quickly and exposing the resulting H₂O₂ solution to UV irradiation. This study focused on evaluating mixing device of H₂O₂ as a design factor of UV/H₂O₂ AOP pilot plant using a surface water. The experimental investigation involved both experimental and model-based analyses to evaluate the mixing effect of different devices available for the H₂O₂ injection of a tubular hollow pipe, elliptical type of inline mixer, and nozzle-type injection mixer. Computational fluid dynamics analysis was employed to model and simulate the mixing devices. The results showed that the elliptical type of inline mixer showed the highest uniformity of 95%, followed by the nozzle mixer with 83%, and the hollow pipe with only 18%, after passing through each mixing device. These results indicated that the elliptical type of inline mixer was the most effective in mixing H₂O₂ in a bulk. Regarding the pressure drops between the inlet and outlet of pipe, the elliptical-type inline mixer exhibited the highest pressure drop of 15.8 kPa, which was unfavorable for operation. On the other hand, the nozzle mixer and hollow pipe showed similar pressure drops of 0.4 kPa and 0.3 kPa, respectively. Experimental study showed that the elliptical type of inline and nozzle-type injection mixers worked well for low concentration (less than 5mg/L) of H₂O₂ injection within 10% of the input value, indicating that both mixers were appropriate for required H₂O₂ concentration and mixing intensity of UV/ H₂O₂ AOP process. Additionally, the elliptical-type inline mixer proved to be more stable than the nozzle-type injection mixer when dealing with highly concentrated pollutants entering the UV/H₂O₂ AOP process. It is recommended to use a suitable mixing device to meet the desired range of H₂O₂ concentration in AOP process.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.834-838
• /
• 1996

The diagnosis of the plasma in the facing targets sputtering system was performed in mixture gas of Ar 0.18-0.0 Pa, Xe 0.0-0.18 Pa and $O_2$ 0.02 Pa by using Langmiur's probe and the effect of plasma-damage to surface smoothness and magnetic characteristics of Ba ferrite films was clarified. The electron density $N_e$ and the electron temperature $T_e$ were evaluated at the center of the plasma and at the neighborhood of the anode ring. $T_e$ decreased and $N_e$ increased with increase of $P_{Xe}$ at the center of plasma. For the measurement at the neighborhood of the anode ring, $T_e$ was almost constant and $N_e$ took the minimum value at $P_{Xe}$ of 0.1 Pa, where Ba ferrite films with excellent c-axis orientation and magnetic characteristics were obtained. It was suggested that the restriction of the bombardment of recoiled particles as well as the suppress of plasma-damage were effective for obtaining good surface smoothness and excellent magnetic characteristics and it was useful for decreasing the crystallization temperature of Ba ferrite films.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.485-488
• /
• 2013

A SiC-$CeO_2$ composite membrane was successfully fabricated using an ally-hydridopolycarbosilane (AHPCS) binder and treated by dip-coating at 60 times with a $CeO_2$ sol solution. The dip-coated SiC membrane was calcined at 773 K and then sintered at 1173 K under an air atmosphere. The coated membrane was characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and a BET surface analysis. The difference in permeation performance between $H_2$ and CO gases was measured by varying the temperature. The permeation flux of $H_2$ on the SiC membrane with layered $CeO_2$ was obtained as $8.45{\times}10^{-6}\;mol/m^2sPa$ at room temperature. The CO permeation flux was $2.64{\times}10^{-6}\;mol/m^2sPa$ at room temperature. The reaction enthalpy (${\Delta}H^{\circ}$) for the hydrogen permeation process was calculated as -7.82 J/mol by Arrhenius plots.

• 한국식품과학회지
• /
• 제37권1호
• /
• pp.30-37
• /
• 2005

유용한 생고분자 필름을 제조하기 위한 목적으로 키토산과 젤라틴을 이용하여 solution casting 방법으로 혼합비율에 따라 혼합필름을 제조하였다. 또한 키토산/젤라틴 혼합필름의 인장 강도, 신장률, 색도, 불투명도, 수분 및 산소 투과도와 같은 물리적인 특성과 열적 특성에 있어 혼합비율이 미치는 효과에 대하여 조사하였다. 혼합비율별로 제조된 키토산/젤라틴 혼합필름의 인장강도는 58.24MPa에서 22.01MPa로 점차적으로 감소 하는 경향을 나타내었고, 신장률은 13.11%에서 24.67%로 인장 강도 결과와는 다르게 증가되는 경향을 보였다. 필름의 외관을 결정하는 중요한 특성인 색도 측정 결과, L 값의 경우 키토산 함량이 증가할수록 감소되었고, a와 b 값은 L 값에 반비례로 증가되었다. 또한 키토산의 함량이 증가함에 따라 제조된 혼합 필름의 ${\Dalta}E$ 및 YI 값들은 키토산 함량 90%를 제외하고는 보다 높은 값들로 측정되었다. 혼합필름의 불투명도는 $0.3104nmO.D./{\mu}m$에서 $1.2161nmO.D./{\mu}m$의 범위로 측정되었다. 수분 투과도는 $1.6875ng{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$에서 $1.7225ng{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$로 측정되었지만, Duncan의 다중비교 분석결과로 키토산의 농도가 증가함에 따라 혼합필름의 수분 투과도는 유의적인(p<0.05) 차이를 나타내지 않았다. 산소 투과도는 혼합비율에 따라 $2.2380{\times}10^{-7}mL{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$에서 $2.2975{\times}10^{-7}mL{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$로 나타났다. 또한 열적 특성을 분석한 결과 혼합비율에 따라 유리전이온도는 단일 곡선을 나타내었고, 젤라틴의 함량이 증가함에 따라 유리전이온도는 증가하였기 때문에 이 결과들을 볼 때, 키토산과 젤라틴 고분자들 사이에 상용성이 있음을 알 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권8호
• /
• pp.1185-1191
• /
• 2008

The core design technology for the multi-effect desalination plant using the thermo compressor (MED-TVC) was investigated by the performance test of multi effect desalination plant in this paper. The final G.O.R (gain of output ratio) of MED-TVC type desalination plant is strongly affected by the performance of thermo-vapor compressor. The present experiments for the desalinating capacity and G.O.R were obtained for the range of the motive steam pressure, 266.0, 250.0, 230.0 and 200.0 kPa. And as a practical problem, to investigate the influence of the sea water temperature to the G.O.R, the inlet steam temperature of the suction water vapor was changed in the range of $311.2{\sim}324.2$ K in the present experiment. Through the experiments, the maximum value of G.O.R was 8.5 at the condition of the motive steam pressure, 136.0 kPa and the minimum value of G.O.R was 8.1 at the condition of the motive steam pressure, 266.0 kPa. And it was confirmed that the range of desalination capacity was $355.2{\sim}264.0$ ton/day in the normal operation condition.