• 센서학회지
• /
• 제6권1호
• /
• pp.6-15
• /
• 1997

이 논문은 빔의 구조를 갖거나 멤브레인의 구조를 갖는 써모파일 센서의 다목적 최적설계에 관한 연구이다. 연구대상의 써모파일 센서는 $Si_{3}N_{4}/SiO_{2}$ 박막위에 알루미늄과 다결정 실리콘을 사용하여 열전쌍을 형성하고, 박막중심부에 $RuO_{2}$를 사용하여 적외선 흡수부를 만들어 중심부와 실리콘림부 사이의 온도차이에 따른 Seebeck 효과에 의한 유기전압을 감지하는 센서를 대상으로 하였다. 최적설계의 목적함수는 센서의 감도, 검출능 (detectivity) 및 열시정수를 대상으로 하였다. 패키지를 고려하여 모델링을 하였으며, 기존의 식의 고찰에 의한 단순 설계방법이 아닌 수학적 계획법을 사용한 다목적 최적화 방법을 이용하여 최적해를 구하였다. 최종적인 최적설계 수식화에는 퍼지계획법에서 사용되는 소속함수를 정의하여 설계자가 우선적으로 신뢰할 수 있는 해를 구 할 수 있도록 하였다. 또한, 제한조건으로서 주위 온도변화에 따른 센서의 출력전압변화를 포함시켜 실제 사용되는 환경을 고려하였다.

• 센서학회지
• /
• 제18권6호
• /
• pp.456-461
• /
• 2009

Perovskite-structure $Sr(Ti_{1-x}Fe_x)O_3$ thick films, in which x is 0.4 or 0.6, were prepared by normal ceramic process on alumina substrate. Electrical resistance was measured as a function of thermal treatment condition including atmosphere, time, and temperature. The resistance of $Sr(Ti_{1-x}Fe_x)O_3$ films is lower than those of $SrTiO_3$ or $SrFeO_3$ films. The temperature coefficient of resistance over $550^{\circ}C$ was measured to be 0 for the $Sr(Ti_{1-x}Fe_x)O_3$ films after thermal treatment at $1100^{\circ}C$ in air. The sensing property of the films was also measured as a function of temperature and gas such as $O_2$, CO, $CO_2$, NO and $NO_2$. $Sr(Ti_{1-x}Fe_x)O_3$ films showed a good sensing property for $O_2$, but no sensing signal for CO, $CO_2$, NO and $NO_2$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1304-1307
• /
• 1997

A hydrogen gas sensor utilizing Pt/$SnO_2$ system was fabricated by the pressed pellet method. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with Electron Diffraction Analysis, Transmission Electron Microscopy, Scanning Electron Microscopy. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30sccm (a mixture of $0.5%H_2$ in $N_2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. $H_2$ gas sensing properties of Pt/$SnO_2$ were investigated at several temperatures. As a result, it was observed that Pt/$SnO_2$ has high sensitivity at $300^{\circ}C$ and $400^{\circ}C$.

• 센서학회지
• /
• 제20권5호
• /
• pp.289-293
• /
• 2011

Networked $SnO_2$ nanowires were uniformly functionalized with Pd nanoparticles via ${\gamma}$-ray radiolysis. The Networked $SnO_2$ nanowires were fabricated through a selective growth method. The sensing properties of the Pd-functionalized $SnO_2$ nanowires were analyzed in terms of their response to $NO_2$ and CO gases. The response time and sensitivity of the sensors were significantly improved for $NO_2$ at lower temperatures by the Pd functionalization. The enhancement in the sensing properties is likely to be due to the spillover effect of the Pd nanoparticles.

• 한국재료학회지
• /
• 제28권1호
• /
• pp.12-17
• /
• 2018

$In_2O_3$ doped $WO_3$ powders were prepared by a polymer solution route and their $NO_2$ gas sensing properties were analyzed. The synthesized powders showed nano-sized particles with specific surface areas of $6.01{\sim}21.5m^2/g$ and the particle size and shape changed according to the content of $In_2O_3$. The gas sensors fabricated with the synthesized powders were tested at operating temperatures of $400{\sim}500^{\circ}C$ and 100~500 ppm concentrations of $NO_2$ atmosphere. The particle size and $In_2O_3$ content affected on the initial sensor resistance in an air atmosphere. The highest sensitivity (8.57 at $500^{\circ}C$), which was 1.77 higher than the sensor consisting of the pure $WO_3$ sample, was measured in the 0.5 mol% $In_2O_3$ doping sample. In addition, the response time and recovery time were improved by the addition of $In_2O_3$.

• 한국재료학회지
• /
• 제21권8호
• /
• pp.468-475
• /
• 2011

[ $LaMeO_3$ ](Me = Cr, Co) powders were prepared using the polymeric precursor method. The effects of the chelating agent and the polymeric additive on the synthesis of the $LaMeO_3$ perovskite were studied. The samples were synthesized using ethylene glycol (EG) as the solvent, acetyl acetone (AcAc) as the chelating agent, and polyvinylpyrrolidone (PVP) as the polymer additive. The thermal decomposition behavior of the precursor powder was characterized using a thermal analysis (TG-DTA). The crystallization and particle sizes of the $LaMeO_3$ powders were investigated via powder X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and particle size analyzer, respectively. The as-prepared precursor primarily has $LaMeO_3$ at the optimum condition, i.e. for a molar ratio of both metal-source (a : a) : EG (80a : 80a) : AcAc (8a) inclusive of 1 wt% PVP. When the as-prepared precursor was calcined at $700^{\circ}C$, only a single phase was observed to correspond with the orthorhombic structure of $LaCrO_3$ and the rhombohedral structure of $LaCoO_3$. A solid-electrolyte impedance-metric sensor device composed of $Li_{1.5}Al_{0.5}Ti_{1.5}(PO_4)_3$ as a transducer and $LaMeO_3$ as a receptor has been systematically investigated for the detection of NOx in the range of 20 to 250 ppm at $400^{\circ}C$. The sensor responses were able to divide the component between resistance and capacitance. The impedance-metric sensor for the NO showed higher sensitivity compared with $NO_2$. The responses of the impedance-metric sensor device showed dependence on each value of the NOx concentration.

• Bulletin of the Korean Chemical Society
• /
• 제32권10호
• /
• pp.3735-3737
• /
• 2011

We report a simple method for fabricating ZnO gas sensors via a sonochemical route and their $H_2$ gas sensing properties. Vertically aligned ZnO nanorod arrays as a sensing material were synthesized on a Pt-electrode patterned alumina substrate under ambient conditions. The advantage of the proposed method is a high speed of processing. The gas sensor based on ZnO nanorod arrays with large specific surface area showed a high response to $H_2$ and a detection limit of 70 ppm at $250^{\circ}C$. Also, their response and recovery time were relatively short and a complete regeneration was observed. A mechanism for sensing $H_2$ gas on the surface of ZnO nanorods is proposed.

• 센서학회지
• /
• 제18권3호
• /
• pp.239-244
• /
• 2009

We fabricated nano-templates by low temperature BCP(block copolymer) process at 180 $^{\circ}C$, then we deposited 10 nm-thick $TiO_2$ layers with ALD(atomic layer deposition) at low temperature of 150 $^{\circ}C$. Through FE-SEM analysis, we confirmed the successful formation of the groove-type(width of crest : 30 nm, width of trough : 18 nm) and the cylinder-type(diameter : 10 nm, distance between hole : 25 nm) templates. Moreover, after $TiO_2$-ALD processing, we confirmed the deposition of the uniform nano layers of $TiO_2$ on the nano-templates. Through AFM analysis, the pitches of the crest-through(in groove-type) and hole-hole(in cylinder-type) were the same before and after $TiO_2$-ALD processing. In addition, we indirectly determined the existence of the uniform $TiO_2$ layers on nano-templates as the surface roughness decreased drastically. We successfully fabricated nano-template at low temperature and confirmed that the three-dimensional nano-structure for sensor application could be achieved by $TiO_2$-ALD processing at extremely low temperature of 150 $^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.65-65
• /
• 2007

Microstructure and surface roughness of the sensing materials should be improved to use them in advanced sensor applications because the uneven surface roughness degrades the light reflection, pattern resolution, and devices performance. Chemical mechanical polishing (CMP) processing was selected for improving the surface roughness of $CeO_2$ which is one of the well known materials for the oxygen gas sensors. Surface roughness and removal rate of spin coated $CeO_2$ thin films were examined with a change of CMP process parameters such as down force and table speed. The optimized process condition, reflected by the surface roughness with the hillock-free surface as well as the excellent removal rate with the good uniformity, was obtained. The effects of the improved surface roughness on the sensing property of $CeO_2$ thin films were also confirmed. The improved sensitivity of $CeO_2$ thin films for oxygen sensors were obtained after CMP process by the improved surface characteristics. Therefore, we conclude that sensing property of $CeO_2$ thin film is strongly dependent on the surface roughness of $CeO_2$ thin films by using CMP process.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.51.3-51.3
• /
• 2010

Due to the recent public awareness of global warming and sustainable economic growth, there has been a growing interest in alternative clean energy sources. Hydrogen is considered as a clean fuel for the next generation. One of the technical challenges related to the use of hydrogen is safe monitoring of the hydrogen leak during separation, purification and transportation. For detecting various gases, chemiresistor-type gas sensors have been widely studied and used due to their well-established detection scheme and low cost. However, it is known that many of them have the limited sensitivity and slow response time, when used at low temperature conditions. In our work, a sensor based on Schottky barriers at the electrode/sensing material interface showed promising results that can be utilized for developing fast and highly sensitive gas sensors. Our hydrogen sensor was designed and fabricated based on indium oxide (In2O3)-doped tin oxide (SnO2) semiconductor nanoparticles with platinum (Pt) nanoclusters in combination with interdigitated electrodes. The sensor showed the sensitivity as high as $10^7%$ (Rair/Rgas) and the detection limit as low as 30 ppm. The sensor characteristics could be obtained via optimized materials synthesis route and sensor electrode design. Not only the contribution of electrical resistance from the film itself but also the interfacial effect was identified as an important factor that contribute significantly to the overall sensor characteristics. This promises the applicability of the developed sensor for monitoring hydrogen leak at room temperature.