• Economic and Environmental Geology
• /
• v.33 no.3
• /
• pp.181-193
• /
• 2000

This study was undertaken to evaluate the drinking water quality based on physicochemical properties and chemical compositions of the supply water in the Daedeok Campus, and to verify the analytical reliabilities of ICP-MS and IC equipped in the Central Research Facilities at Chungnam National University , Korea. The supply water belongs to $Ca^{2+}-({HCO_3}^-+{SO_4}^{2-})$type, whereas the original water from the Daecheong lake belongs to $(Ca^{2+}-(Mg^{2+})-{HCO_3}^-$ type. Generally, temperature (14.1$^{\circ}C$), pH (6.95), Eh (0 mV), electrical conductivity (117${\mu}$S/cm) and TDS (86.975mg/l) of supply water were higher than those of original lake water . Results using WATEQ4F revealed that potentially toxic ions of the supply water might exist mainly as free metals ($M^{2+}$) and a small amount as ${CO_3}^{2-}$ and $OH^-$ complexes. Also, the water composition belongs to the kaolinite field. Calculated average enrichment indies of the supply water normalized to lake water for anions, mamor cations, toxic cations and total ions are 1.05 , 1.56, 13.05 and 1.17 , respectively. Those values of the ground water in the Daedeok Campus showed 1.71, 4.78, 5.71 and 2.49 , respectively. However , contents of all constituents of these water are within the drinking water standard. All samples were filtered before the chemical analysis. Pale yellow or yellowish brown colored materials of colloidal particles coated the filter paper to thickness of 0.02 to 0.2mm. these are mainly Fe-Cy-Zn compounds with traces of Ni and Pb, the net weights of which compounds range from 0.01to 3.20mg/l. Most elements did not show any conceivable filtering effect of Cu, Fe and Zn. Especially, mean concentration of total Fe decreased considerably from 168.52${\mu}g$/lto 42.58${\mu}g$/l by filtering .

• Journal of Microbiology and Biotechnology
• /
• v.33 no.11
• /
• pp.1521-1530
• /
• 2023

An α-L-rhamnosidase gene from Thermoclostridium. stercorarium subsp. thermolacticum DSM 2910 (TstRhaA) was cloned and expressed. The maximum TstRhaA activity of the protein reached 25.2 U/ml, and the molecular mass was approximately 106.6 kDa. The protein was purified 8.0-fold by Ni-TED affinity with an overall recovery of 16.6% and a specific activity of 187.9 U/mg. TstRhaA activity was the highest at 65℃ and pH 6.5. In addition, it exhibited excellent thermal stability, better pH stability, good tolerance to low concentrations of organic reagents, and high catalytic activity for p-nitrophenyl-α-L-rhamnopyranoside (pNPR). Substrate specificity studies showed that TstRhaA exhibited a high specific activity for rutin. At 60℃, pH 6.5, and 0.3 U/ml enzyme dosage, 60 g/l rutin was converted to 45.55 g/l isoquercitrin within 150 min. The molar conversion rate of rutin and the yield of isoquercitrin were 99.8% and 12.22 g/l/h, respectively. The results suggested that TstRhaA could be used for mass production of isoquercitrin.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.26 no.2
• /
• pp.225-236
• /
• 2016

Objectives: Nanomaterials have been used in various fields. As use of nanoproducts is increasing, workers dealing with nanomaterials are also gradually increasing. Exposure assessments for nanomaterials have been carried out for protection of worker's health in workplace. Exposure studies were mainly focused on manufacturing processes, but these studies on after-treatment processes such as refinement, weighing, and packing were insufficient. So, we investigated exposure characteristics of particles during after-treatment processes of $Al_2O_3$ fibers and Ni powders. Methods: Mass-production of Ni powder process was carried out in enclosed capture-type canopy hood. In a developing stage, $Al_2O_3$ was handled with a local ventilation unit. Exposure characteristics of particles were investigated for $Al_2O_3$ fiber and Ni powder processes during the periods of 10:00 to 16:00, 20 May 2014 and 13:00 to 16:00, 21 May 2014, respectively. Three real-time aerosol instruments were utilized in exposure assessment. A scanning mobility particle sizer(SMPS, nanoscan, model 3910, TSI) and an optical particle counter(OPC, portable aerosol spectrometer, model 1.109, Grimm) were used to determine the particle size distribution in the size range of 10-420 nm and $0.25-32{\mu}m$, respectively. In addition, a nanoparticle aerosol monitor(NAM, model 9000, TSI) was used to measure lung-deposited nanoparticle surface area. Membrane filters(isopore membrane filter, pore size of 100 nm) were also used for air sampling for the FE-SEM(model S-5000H, Hitachi) analysis using a personal sampling pump(model GilAir Plus by 2.5 L/min, Gilian). Conclusions: For Ni powder after-treatment process, only 27% increase in particle concentration was found during the process. However, for $Al_2O_3$ fiber after-treatment process, significant exposure(1.56-3.34 times) was observed during the process.

• Journal of Microbiology and Biotechnology
• /
• v.18 no.4
• /
• pp.670-675
• /
• 2008

A laccase was isolated from the culture filtrate of the basidiomycete Fomitella fraxinea. The enzyme was purified to electrophoretical homogeneity using ammonium sulfate precipitation, anion-exchange chromatography, and gel-filtration chromatography. The enzyme was identified as a monomeric protein with a molecular mass of 47 kDa by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and gel-filtration chromatography, and had an isoelectric point of 3.8. The N-terminal amino acid sequence for the enzyme was ATXSNXKTLAAD, which had a very low similarity to the sequences previously reported for laccases from other basidiomycetes. The optimum pH and temperature for 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS) were 3.0 and $70^{\circ}C$, respectively. The enzyme also showed a much higher level of specific activity for ABTS and 2,6-dimethoxyphenol (DMP), where the $K_m$ values of the enzyme for ABTS and 2,6-DMP were 270 and $426{\mu}M$, respectively, and the $V_{max}$ values were 876 and $433.3{\mu}M/min$, respectively. The laccase activity was completely inhibited by L-cysteine, dithiothreitol (DTT), and sodium azide, significantly inhibited by $Ni^+,\;Mn^{2+}$, and $Ba^{2+}$, and slightly stimulated by $K^+$ and $Ca^{2+}$.

• Journal of the Korean Chemical Society
• /
• v.59 no.3
• /
• pp.215-224
• /
• 2015

Unsymmetrical tetradentate Schiff base N-(2-hydroxy-5-methylacetophenone)-N'-(2-hydroxy acetophenone) ethylene diamine (H₂L) and its complexes with Cr(III), Mn(II), Fe(III), Co(II), Ni(II) and Cu(II) have been synthesized and characterized by elemental analyses, magnetic susceptibility measurements, IR, electronic spectra and thermogravimetric analyses. ¹H, ¹³C-NMR and FAB Mass spectra of ligand clearly indicate the presence of OH and azomethine groups. Elemental analyses of the complexes indicate that the metal to ligand ratio is 1:1 in all complexes. Infrared spectra of complexes indicate a dibasic quadridentate nature of the ligand and its coordination to metal ions through phenolic oxygen and azomethine nitrogen atoms. The thermal behavior of these complexes showed the loss of lattice water in the first step followed by decomposition of the ligand in subsequent steps. The thermal data have also been analyzed for the kinetic parameters by using Horowitz-Metzger method. The dependence of the electrical conductivity on the temperature has been studied over the temperature range 313-403 K and the complexes are found to show semiconducting behavior. XRD and SEM images of some representative complexes have been recorded. The antimicrobial activity of the ligand and its complexes has been screened against various microorganisms and all of them were found to be active against the test organisms. The Fe(III) and Ni(II) complex have been tested for the catalytic oxidation of styrene.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.7-13
• /
• 1998

In this study, for the safety performance of LNG storage tank, the fracture toughness in X-grooved weld HAZ(heat-affected zone) of $9\%$ Ni steel was evaluated qualitatively and quantitatively, and the relation with the change in microstructure was analyzed. The toughness assessment was peformed through the modified CTOD test proposed for thick weldment with X-groove. Additionally, microstructures of HAZ were evaluated by OM, SEM and XRD. From the results, HAZ toughness of SMA(shielded metal arc)-welded $9\%$ Ni steel decreased as the evaluated region approached the fusion line. The decrease in toughness was apparently caused by the increase in the fraction of coarse-grained zone within HAZ. On the other hand, toughness drop with decreasing test temperature in F.L.(fusion line) ${\~}$F.L.+3mm was larger than that in F.L.+5mm${\~}$F.L.+7mm region due to the fact that in the former regions, retained austenite had poor stability.

• Analytical Science and Technology
• /
• v.13 no.5
• /
• pp.608-615
• /
• 2000

A determination method of trace nickel and cobalt in water samples was studied and developed by adsorbing their complexes on ion exchange resin suspension. The analytical ions were formed as complexes with a ligand of APDC (ammonium pyrrolidinedithiocarbamate) and adsorbed on anion exchange resin of Dowex 2-X8. After the suspension was filtered out with membrane filter, the complexes were dissolved in HCl solution by an ultrasonic vibrator for ET-AAS determination. Several conditions were optimized as followings. pH of sample solution: 5.0, amount of ligand APDC: more than 430 times in mole ratio, the type and concentration of acid: 0.1 M HCl, and vibration time: 7 minutes. The addition of palladium in the HCl solution could improve the reproducibility and sensitivity by a matrix modification in the absorbance measurement. This procedure was applied for the analysis of three kinds of real water samples. The detection limits equivalent to 3 times standard deviation of blank were Co 0.36 ng/mL and Ni 0.27 ng/mL and recoveries in spiked samples were 99-102% for cobalt and 100-105% for nickel.

• Korean Journal of Microbiology
• /
• v.51 no.2
• /
• pp.115-125
• /
• 2015

A monoclonal antibody AP64 IgM binds to human acute nonlymphocytic leukemia (ANLL) cell line HL60 and also cross-reacts with the homologous antigen in a rat ANLL cell. This antibody mediated by complement, has leukemia a suppression effect. In this study, we generated a recombinant single-chain variable domain fragment (ScFv) which were derived from $V_H$ and $V_L$ cDNA of AP64 IgM-secreting hybridoma by RT-PCR. The two variable regions were joined with a single 15 amino acid linker $(G_4S)_3$. This recombinant ScFv was expressed as a single polypeptide chain from Escherichia coli BMH 71-18. The recombinant ScFv was purified by applying the periplasmic extract to $Ni^+$-NTA-agarose affinity column and detected with westernblot. The purified recombinant ScFv recognized a surface antigen (about 30 kDa) of HL60 cell line which is the same antigen detected by parental AP64 IgM. But the affinity of ScFv for a surface antigen of HL60 was lower than that of the parental AP64 IgM, which needs to be further improved. Overall, the recombinant ScFv specific to HL60 might be a useful bioreagent for either diagnostic or therapeutic purposes.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.152-156
• /
• 1997

In this paper, I meritioned ,I study on thc rnechanochernic;~l effec ts of grountl iljckite To investigate the mechanochemical effects of ground tlickite 1,y planet,~r\- mill. a structul-ill i~nalvsis of dickite prepared with different grinding time has been made 11y X-ray diffraction and ilifierenti,~l tl~i.~-ni;~i analysis. 'l'he $SiO_{4}$ hecira was unchanged bl- milling and remained ;is the local ordering unit s t t - ~ c ~ u ~ - c ~ s in the ground dickitc samples I ) v analyzing the radial distribution function. On the other hand, with an increi~se of the grinding time a decrease of coordination number and atomic distance bet\vccn aluminum and oxygen hi1c.r l~een octurreil, and Li~~antitativcl\. coniirrned them This result corresponded to the local c,hange around aliimi~iuni I>V tliftercntii~l t1ii:rm;il ani~lysis. Therefore, the mechanochemical phenomina of ground tiickite werc3 h e to the local c~l~mge around aluminum \IT. the prolonged grinding.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.2
• /
• pp.254-263
• /
• 2020

Objective: The objective of this study was to investigate the effects of wilting and additives on the fermentation quality, structural and non-structural carbohydrate composition of mulberry silages. Methods: The selected lactic acid bacteria strains Lactobacillus plantarum 'LC279063' (L1), commercial inoculant Gaofuji (GF), and Trichoderma viride cellulase (CE) were used as additives for silage preparation. Silage treatments were designed as control (CK), L1, GF, or CE under three wilting rates, that is wilting for 0, 2, or 4 hours (h). After ensiling for 30 days, the silages were analyzed for the chemical and fermentation characteristics. Results: The results showed that wilting had superior effects on increasing the non-structural carbohydrate concentration and degrading the structural carbohydrate. After ensiling for 30 days, L1 generally had a higher fermentation quality than other treatments, indicated by the lower pH value, acetic acid, propionic acid and ammonia nitrogen (NH₃-N) content, and the higher lactic acid, water soluble carbohydrate, glucose, galactose, sucrose, and cellobiose concentration (p<0.05) at any wilting rate. Wilting could increase the ratio of lactic acid/acetic acid and decrease the content of NH₃-N. Conclusion: The results confirmed that wilting degraded the structural carbohydrate and increased the non-structural carbohydrate; and L1 exhibited better properties in improving fermentation quality and maintaining a high non-structural carbohydrates composition compared with the other treatments.