• Journal of the Korean Applied Science and Technology
• /
• v.21 no.2
• /
• pp.174-181
• /
• 2004

Multi-walled carbon nanotubes (CNTs) were prepared by thermal chemical vapor deposition (CVD) and microwave plasma chemical vapor deposition (MPCVD) using various combination of binary catalysts with four transition metals such as Fe, Co, Cu, and Ni. In the preparation of CNTs from acetylene precursor by thermal CVD, the CNTs with very high yield of 43.6 % was produced over $Fe-Co/Al_2O_3$. The highest yield of CNTs was obtained with the catalyst reduced for 3 hr and the yield was decreased with increasing reduction time to 5 hr, due to the formation of $FeAl_2O_4$ metal-aluminate. On the other hand, the CNTs prepared by acethylene plasma CVD had more straight, smaller diameter, and larger aspect ratio(L/D) than those prepared by thermal CVD, although their yield had lower value of 27.7%. The degree of graphitization of CNTs measured by $I_d/I_g$ value and thermal degradation temperature were 1.04 and $602^{\circ}C$, respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.554-561
• /
• 2016

Depending on the Bio-gas sources, main component gases of $CH_4$ and $CO_2$ are shown to be variously present in amounts. For the anaerobic digester, The concentration of $CH_4$ and $CO_2$ in the gases are 60~70 and 30~35 vol%. For the landfill gas, $CH_4$ and $CO_2$ are 40~60 and 40~60 vol%. For the food wastes, $CH_4$ and $CO_2$ are 60~80 and 20~40 vol%, respectively. In this study, maximum conversion rates of $CO_2$ were obtained from the variety of concentrations of $CH_4$ and $CO_2$ by the catalysts of reforming reactions. Moreover, in order to get maximum producing amount of synthetic gas, experimental studies were performed to optimize the reaction variables. On the basis of $CH_4$, 243 ml, R [$CH_4/(O2+CO_2)$] value were varied from 0.8 to 1.35, in the study of $CH_4$ and $CO_2$ reforming reactions. It was shown that the optimal results were obtained for 1.35 of R value. And also, at $850^{\circ}C$ and 1 atm, the production rate of synthetic gas was 90% and the conversion rates of $CH_4$ and $CO_2$ were higher than 99% and 90%, respectively.

• Clean Technology
• /
• v.25 no.3
• /
• pp.256-262
• /
• 2019

Hydroxylammonium nitrate (HAN)-based liquid propellants are attracting attention as environmentally friendly propellants because they are not carcinogens and the combustion gases have little toxicity. The catalyst used to decompose the HAN-based liquid propellant in a thruster must have both low temperature activity and high heat resistance. The objective of this study is to prepare an Ru/alumina/metal foam catalyst by supporting alumina slurry on the surface of NiCrAl metal foam using a washing coating method and then to support a ruthenium precursor thereon. The decomposition activity of a HAN aqueous solution of the Ru/alumina/metal foam catalyst was evaluated. The effect of the number of repetitive coatings of alumina slurry on the physical properties of the alumina/metal foam was analyzed. As the number of alumina wash coatings increased, mesopores with a diameter of about 7 nm were well-developed, thereby increasing the surface area and pore volume. It was optimal to repeat the wash coating alumina on the metal foam 12 times to maximize the surface area and pore volume of the alumina/metal foam. Mesopores were also well developed on the surface of the Ru/alumina/metal foam catalyst. It was found that the metal form itself without the active metal and alumina can promote the decomposition reaction of the HAN aqueous solution. In the case of the Ru/alumina/metal foam-550 catalyst, the decomposition onset temperature was significantly lowered compared with that of the thermal decomposition reaction, and ${\Delta}P$ could be greatly increased in the decomposition of the HAN aqueous solution. However, when the catalyst was calcined at $1,200^{\circ}C$, the catalytic activity was lowered inevitably because the surface area and pore volume of the catalyst were drastically reduced and Ru was sintered. Further research is needed to improve the heat resistance of Ru/alumina/metal foam catalysts.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.267-273
• /
• 2012

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber-the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam-was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.80-86
• /
• 2011

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber - the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam - was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• Clean Technology
• /
• v.17 no.1
• /
• pp.56-61
• /
• 2011

In this study, hydrocarcking of vacuum residue was carried out in an autoclave reactor at $450^{\circ}C$ and $500^{\circ}C$ with a commercial catalyst (HDM) and the quantitative product distributions were analyzed by GC-SIMDIS method or simple distillation. During catalytic hydrocracking, thermal cracking also occurred together with catalytic cracking and the higher conversion and selectivity of gasoline and naphtha were obtained at high reaction temperature. GC-SIMDIS and simple distillation revealed different results for the analysis of products produced at different hydrocracking temperatures; almost same results were obtained for the product produced at $500^{\circ}C$ but different ones for the product produced at $450^{\circ}C$. In the analysis of product produced at $450^{\circ}C$, the GC-SIMDIS showed that a main product was VGO while a main product in the simple distillation was diesel, which implies that the simple distillation for the $450^{\circ}C$ reaction was not accurate due to thermal cracking of the product by the simple distillation.