• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.237-243
• /
• 1999

스크린 프린팅법을 이용하여 NOX 감지용 WO3 후막형 가스센서를 제조하였다. 본 실험에서는 감지막의 소성 온도에따른 감도변화 및 Ru을 첨가함으로써 감도의 증진을 중점적으로 조사하였다. 또한 NO2 50 ppm하에서 CO, H2, CH4 그리고 i-C4H10등의 가스에 대하여 cross sensitivity를 조사하였다. WO3 가스센서는 소성온도 50$0^{\circ}C$, 작동온도 30$0^{\circ}C$에서 최대감도를 얻었다. 순수한 WO3에 Ru(0.004 wt%)을 첨가시 NO2 및 NO 가스에 대한 감도가 크게 증진되었다. 그러나 순수한 WO3 센서는 Ru(0.004 wt%)이 첨가된 WO3 센서보다 더 우수한 cross sensitivity를 보였다.

• Journal of Sensor Science and Technology
• /
• v.8 no.2
• /
• pp.108-114
• /
• 1999

Surface acoustic wave (SAW) device is very attractive for gas sensor applications because of their small size, low cost, high sensitivity, and good reliability. A dual delay line surface acoustic wave $NO_2$ gas sensors have been designed and fabricated on the $LiTaO_3$ piezoelectric single crystal substrate. The capacitance of the fabricated IDTs was 326.34pF at the frequency of 79.3MHz. The maximum reflection loss of the impedence-matched IDTs was -16.74dB at the frequency of 79.3MHz. The SAW oscillator was constructed and the stable oscillation was obtained by controlling the gain of rf amplifier properly. The oscillation frequency shift of the SAW oscillator to the $NO_2$ gas was 28Hz/ppm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.105-108
• /
• 1998

Pt-WO$_3$-Si$_3$N$_4$-SiO$_2$-Si-Al 캐패시터를 이용한 NO$_2$ 가스 센서를 개발하였다. 표준 실리콘 MNOS구조에 촉매 게이트로 Pt와 가스 흡착층으로 WO$_3$를 이용함으로서 전통적인 세라믹 가스 센서보다 낮은 온도에서 NO$_2$ 가스를 감지할 수 있었다. 은도 변화와 NO$_2$ 가스 농도의 변화에 따라서 디바이스의 NO$_2$ 가스 감도를 조사하였다. Pt-WO$_3$ 계면에서 NO$_2$ 이온농도의 변화에 기초로 한 가스 감지 모델을 제시하였다. 제시된 가스 감지 모델을 계면에서의 가스 반응 속도론에 의하여 분석함으로서 확인하였다.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.188-196
• /
• 1998

The sensing and electrical characteristics of $WO_{3}$-based n-type semiconductor gas sensors are investigated. In normal air condition, $TiO_{2}$(4 wt. %)-doped $WO_{3}$-based sensor fabricated without any binder shows the grain boundary ( GB ) potential barrier height of 0.26 V. Sensors fabricated with alumina, PVA and silica sol binders show 0.17, 0.22 and 0.26 V of GB potential barrier height, respectively. In the ambience of 120 ppm $NO_{x}$ concentration, the GB potential barrier height of the sensor fablicated without binder is increased to 0.59 V. The sensors were fabricated with alumina, PVA, silica sol binders show 0.43, 0.66 and 0.52 V of potential barrier, respectively. Thus the variation of the potential barrier at GB is largest in the sensor fabricated with the PVA binder. This is found to be the main reason why the sensor fabricated with the PVA binder shows the best sensitivity. It is also found that the decrease of sensitivity at a temperature higher than the optimum operation temperature is due to the temperature dependence of the sensor resistance in normal air condition rather than the desorption of the adsorbed $NO_{x}$ gas particles. In the ambience of 250 ppm CO concentration, the GB potential barrier heights of the sensors fabricated without binder and with PVA binder are about 0.2 V showing negligible change compared to the case of normal air ambience. This fact indicates that these sensors are good candidates for the selective detection of $NO_{x}$ gas in the mixture of CO and $NO_{x}$ gases.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.2 s.43
• /
• pp.59-63
• /
• 2007

This paper presented a low-cost thick film gas sensor module, which was based on simple PCB (Printed Circuit Board) process. The proposed sensor module included a $NO_2/H_2$ gas sensor, a relative humidity sensor, and a heating element. The $NO_2/H_2$ gas and relative humidity sensors were realized by screen-printing $SnO_2,\;BaTiO_3$ nano-powders on IDTS (Interdigital Transducer) of a PCB substrate, respectively. At first 1% $H_2$ gas flowed into the sensor chamber. After 4 min, air filled the chamber while $H_2$ gas flow stopped. This experiment was performed repeatedly. The Identical procedure was used for the $NO_2$ detection. The result for sensing $H_2$ gas showed the increase of voltage from 0.8V to 3.5V due to the conductance increase and its reaction response time by hydrogen flow was 65 sec. $NO_2$ sensing results showed 2.7 V voltage drop due to the conductance decrease and its response time was 3 sec through a voltage monitoring.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.102-102
• /
• 2000

최근 자동차 배기 가스 유출에 의한 환경문제가 심각하게 대두되고 있고, 이에 따라 그 중 NOx, SOx 등의 유해가스 검출을 위한 센서 개발이 강력히 요구되고 있다. 본 실험은 자동차에서 배출되는 NO 가스에 대한 민감한 센서 제작을 목적으로 In2O3 박막을 성장시켜 그 특성을 측정하였고, NO 가스에 대한 민감도를 증가시키기 위해 7 ~32 정도의 초박막 Co 촉매를 증착하여 NO 감도에 미치는 현상을 조사하였다. In2O3 2˝ target(순도 99.99%)을 사용하여 RF power와 Ar/O2의 비를 변화시켜가면서 상온에서 알루미나 기판위에 In2O3 박막 성장시켰다. 박막을 성장시킨 후 10$0^{\circ}C$에서 5$0^{\circ}C$까지 온도를 변화시키면서 공기 중에서 열처리를 하였다. In2O3 박막의 결정성은 XRD를 이용하여 측정하였고 표면 특성을 알아보기 위해 AFM과 SEM 측정을 하였다. XRD 분석결과 상온에서부터 50$0^{\circ}C$까지 회절 peck의 강도차이는 있었지만 모든 시편에서 In2O3 박막이 cubic 구조로 성장함을 알 수 있었다. 100ppm 농도 NO 가스에 대한 센서 소자의 감도를 20$0^{\circ}C$~40$0^{\circ}C$ 온도 영역에서 측정하였다. 순수한 In2O3 의 경우 감도(S=Ra/Rg)는 25$0^{\circ}C$에서 S 6 정도로 가장 좋았다. 반면에 Co 촉매를 표면에 흡착시킨 경우 20$0^{\circ}C$~25$0^{\circ}C$ 부근에서 반응속도가 매우 빨라지고, 150 정도 Co를 흡착시킨 센서의 경우 S 14 로 감도가 매우 향상됨을 알 수 있었다.

• Journal of Sensor Science and Technology
• /
• v.17 no.1
• /
• pp.61-68
• /
• 2008

The sensing characteristics of new oxide sensing materials, NiO, NiO-YSZ and CuO, were evaluated at the temperature of $700^{\circ}C$ in 10 % $O_2$containing atmosphere. Through simultaneous response to $NO_2$ and NO, the sensing mechanism of oxide electrode was studied and the relation of EMF and NO/$NO_2$ concentrations was elucidated. Moreover, for highly sensitive NOx sensor, modified mixed potential sensor which has at least two oxide electrodes was proposed.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.3 s.36
• /
• pp.227-233
• /
• 2005

Carbon nanotubes (CNT) which were grown, on the alumina substrate with a pair of comb-type Au electrodes, by plasma enhanced chemical vapor deposition have been investigated for $NO_2$ gas sensor. The electrical resistance of CNT film decreased with temperature, indicating a semiconductor type of CNT, and also the resistance of CNT sensor decreased with increasing $NO_2$ concentration. Upon exposure to $NO_2$ gas, the electrical resistance of CNT film sensor rapidly decreased within 3 minutes, and then showed a constant value after $20\~30$ minutes. It is found that the sensitivity of CNT sensor has been improved by air oxidation. The CNT sensor oxidized at $450^{\circ}C$ for 30 minutes showed higher sensitivity value than that without oxidation by $27\%$, even for a low 250 ppb $NO_2$ concentration at operating temperature of $200^{\circ}C$. But it needs a recovery time more than 20 minutes for reuse after detection of $NO_2$ gas.

• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.285-291
• /
• 2013

The effects of sensing materials, coating methods, diluent gases, and temperature have been studied in detail to make a quartz crystal microbalance based adsorption sensor system for detecting gases. In particular, sensor elements for detecting $NO_2$ and $SO_2$, that are known as major air pollutants, have been prepared by coating two different polymers, polypyrrole and poly(3,4-ethylenedioxythiophene). The sensor elements prepared in this work have high sensitivity and selectivity for $NO_2$ and $SO_2$ at ppm level concentrations. It was proven that the sensing characteristics and response rate of the sensing elements are highly dependent on the coating method and the loading mass of sensing materials.

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.118-124
• /
• 2001

When particles are dissolved in solution, they have different zeta-potentials depending on pH. Zeta-potential has an influence on particle separation, which can control particle size. And the size of $WO_3$ particle affects the sensitivity of $WO_3$ sensor for detecting NO gas. Therefore we study influence of pH on NO-sensing $WO_3$ gas sensor fabricated by Sol-Coprecipitation method. As pH increases from 2 to 7, dynamic mobility of $WO_3$ precursor was increased. When pH was 7, it showed the largest distribution separation. It means when pH is 7, we can make $WO_3$ powder which has smaller particle size. And it is confirmed by particle size analysis of $WO_3$ powder, X-ray diffration result of $WO_3$ sensing layer and surface morphology. It also affect NO sensing characteristics of $WO_3$ gas sensor. The sensing film synthesized at pH 7 showed the largest sensitivity.