• 농업과학연구
• /
• 제2권1호
• /
• pp.61-100
• /
• 1975

수도재배(水稻栽培)에 있어 작중토(作中土)의 유효규산함량(有效珪酸含量), ppm과 유기물함량(有機物含量)% 비(比) $SiO_2$/O.M. 근거(根據)한 N 적량(適量) 추정식(推定式) $Nkg/10a=(4.2+0.096\;SiO_2/O.M.).F$에서 N시비량(施肥量)을 추정(推定) 시용(施用)할 때의 적정(滴定) 가리(加里) 시용량(施用量) 추정식(推定式) $K_2Okg/10a=(K_O/\sqrt{Ca+Mg}-Ks/\sqrt{Ca+Mg})\sqrt{Ca+Mg}{\cdot}47{\cdot}BD$ 단 (但) $K_O/\sqrt{Ca+Mg}=0.03158+0.0007658\;SiO_2/O.M.$ $K_S/\sqrt{Ca+Mg}=Kme/100g/\sqrt{(Ca+Mg)}me/100g$의 타당성(妥當性) 여부(如否)를 판단(判斷)하기 위하여 3수준(水準)의 규회석처리(珪灰石處理)를 주구(主區)로하여 작토중(作土中)의 $SiO_2$/O.M. 비(比)를 증대(增大) 시키고 각주구별(各主區別)로 적정가리시용량(適正加里施用量) 추정식(推定式)에서 추정(推定)한 $K_2O$ 시용량(施用量)과 이에30%를 증비(增肥)하는구(區) 및 적정가리시용추정치(適正加里施用推定値)와는 관계(關係)없이 $K_2O\;8kg/10a$를 시용(施用)하는 3개수준(個水準)의 $K_2O$ 처리구(處理區)를 설정(設定)하여 수도품종(水稻品種) Akibare를 재배(栽培)하는 포장시험(圃場試驗)을 수행(遂行)하고 토양(土壤), 식물체분석(植物體分析) 및 수도(水稻)의 생육(生育)과 수량(收量) 및 수량구성요소(收量構成要素)들을 조사(調査)한 성적(成績)들을 종합검토(綜合檢討)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 작토중(作土中) 유효규산함량(有效珪酸含量) ppm과 유기물함량(有機物含量)%비(比), $SiO_2$/O.M.에 근거(根據)한 수도(水稻)에 대(對)한 N적량추정식(適量推定式)에서 추정(推定)한 N시용량(施用量)은 수도품종(水稻品種) Akibare의 생육(生育) 및 수량면(收量面)에서 볼 때 과량(過量)이었으며 토양(土壤) 및 식물체(植物體) 분석치(分析値)들에서 검토(檢討)한 결과(結果) $SiO_2$/O.M. 비조절(比調節)의 기본원리(基本原理)는 합당(合當)하나 그 식(式)의 상수(常數) 또는 F값은 변동(變動)되여야 한다고 판단(判斷)되였다. 2. 작토중(作土中)의 K활성도(活性度) 치환성(置換性) 염기 me/100 g비(比) $K/\sqrt{Ca+Mg}$를 조절(調節)하기 위한 $K_2O$ 시비량(施肥量) 추정식(推定式)에서 추정(推定)한 $K_2O$ 시용량(施用量)은 수도품종(水稻品種) Akibare의 생육(生育) 및 수량면(收量面)에서 과량(過量)이였으며 토양(土壤) 및 식물체(植物體) 분석치(分析値)들에서 검토(檢討)한 결과(結果) 조절기준(調節基準)되는 $K_O/\sqrt{Ca+Mg}$의 설정식(設定式) 즉(卽) $K_O/\sqrt{Ca+Mg}=0.03158+0.0007658\;SiO_2/O.M.$의 원리(原理)는 합리적(合理的)이나 기상수(其常數)의 변동(變動)이 필요(必要)하며 $K_S/\sqrt{Ca+Mg}$에 있어서도 토양(土壤)의 K공급능(供給能)을 고려(考慮)할수 있는 새로운 조절기준(調節基準)이 설정(設定)되어야 한다고 판단(判斷)되였다. 3. 수도(水滔)에 대한 $K_2O$ 시용량(施用量) 추정식중(推定式中)의 $K_S/\sqrt{Ca+Mg}$ 조절(調節) 기준(基準)은 K 공급능(供給能)을 대표(代表)할수 있는 작토중(作土中)의 치환성(置換性) Kme/100g에 근거(根據)해서 마음과 같이 설정(設定)함이 보다 합리적(合理的)임을 수도품종(水稻品種) Akibare의 천상수량 $K_2O$ 흡수량면(吸收量面)에서 밝힐수 있었다. 즉 $K_S/\sqrt{Ca+Mg}=0.037+0.78Kme/100g$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1338-1342
• /
• 2005

We have synthesized an $Eu^{2+}$-activated $Sr_3MgSi_2O_8$ blue phosphor and $Ba_2SiO_4$ green phosphor and $Ba^{2+}$ co-doped $Sr_3SiO_5$ red phosphor investigated an attempt to develop white LEDs by combining it with a GaN blue LED $chip(\lambda_{em}=405 nm)$. Three distinct emission bands from the GaN-based LED and the $(Sr_3MgSi_2O_8:Eu\; +\; Ba_2SiO_4:Eu\; +\; Ba^{2+}\; co-doped\; Sr_3SiO_5:Eu)$ phosphor are clearly observed at 460nm, 520 nm and at around 600 nm, respectively. These three emission bands combine to give a spectrum that appears white to the naked eye. Our results show that GaN (405 nm chip)-based $(Sr_3MgSi_2O_8:Eu\; +\; Ba_2SiO_4:Eu\; +\; Ba^{2+}\; co-doped\; Sr_3SiO_5:Eu) exhibits a better luminous efficiency than that of the industrially available product InGaN (460 nm chip)-based YAG:Ce.

• 한국환경보건학회지
• /
• 제39권3호
• /
• pp.223-229
• /
• 2013

Objectives: In an effort to examine the distribution of THMs (Trihalomethane) generated from chlorine disinfection by the drinking water treatment plants located on the east coast region of Gangwon-do, this study surveyed the distribution and concentrations of each component of THMs twice per month for 5 years from 2008 to 2012. Fluctuation pattern in the seasonal generation amount was identified. In addition, the correlation between the concentration of organic substances in water and THMs was assessed, along with stability of purified water quality supplied by the water treatment plants on the east coast by analyzing the composition ratio of each component that constitutes THMs and the detection frequency. Method: The research was done on purified water supplied by 29 water treatment plants in 7 cities and counties (Goseong-gun, Sokcho-si, Yangyang-gun, Gangneung-si, Donghae-si, Samcheok-si, Taebaek-si) located in Gangwon-do on the east coast. Water samples were collected twice a month from 2008 to 2012 and were investigate for chloroform, bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform, based on analysis through Purge-Trap (Tekmar 3000) devices using FID-attached GC (HP 6890, Hewlett Packard). Result: THMs concentration detected at Gangneung-si was 0.0086mg/L, Goseong-gun 0.0019mg/L, Donghae-si 0.0099 mg/L, Samcheok-si 0.0016 mg/L, Sokcho-si 0.0057 mg/L, Yangyang-gun 0.0027 mg/L and Taebaek-si 0.0038 mg/L. As the THMs composition rate, chloroform constitutes 51.4% followed bybromodichloromethane 22.3%, bromoform 15.2% and dibromochloromethane 11.1% respectively. Conclusion: Throughout the entire THMs survey areas and period, the maximum concentration was 0.072mg/L, which did not exceed the water quality standards (0.1 mg/L), and the overall average concentration was very low at 0.0044 mg/L.

• 소성∙가공
• /
• 제26권5호
• /
• pp.306-313
• /
• 2017

This study investigated the microstructure, tensile strength, and high cycle fatigue properties of ADC12 aluminum alloys with different $Mg+Al_2Ca$ contents manufactured using die casting process. Microstructural observation identified the presence of ${\alpha}-Al$, eutectic Si, $Al_2Cu$, and Fe-intermetallic phases. The increase of $Mg+Al_2Ca$ content resulted in finer pore size and decreased pore distribution. Room temperature tensile strength tests were conducted at strain rate of $1{\times}10^{-3}/sec$. For 0.6%Mg ADC12, measured UTS, YS, and El were 305.2MPa, 157.0MPa, and 2.7%, respectively. For 0.8%Mg ADC12, measured UTS, YS, and El were 311.2 MPa, 159.4 MPa, and 2.4%, respectively. Therefore, 0.8% ADC12 alloy had higher strength and slightly decreased elongation compared to 0.6% Mg ADC12. High cycle fatigue tests revealed that 0.6% Mg ADC12 alloy had a fatigue limit of 150 MPa while 0.8% Mg ADC12 had a fatigue limit of 160MPa. It was confirmed that $Mg+Al_2Ca$ added ADC12 alloy achieved finer, spherical eutectic Si particles, and $Al_2Cu$ phases with greater mechanical and fatigue properties since size and distribution of pores and shrinkage cavities decreased as $Mg+Al_2Ca$ content increased.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.127-135
• /
• 1992

It has been reported that natural petalite showed a low negative thermal coefficient and wide coefficient and wide coexisting region with liquid phase in Li2O-Al2O3-SiO2 system. Therefore, we investigated variation of microstructure and thermal and mechanical properties when the amount of SiO2 content in petalite compound and MgO addition to it compound were changed. As SiO2 content exceeded 80 wt%, crystal phases of $\beta$-cristobalite and $\beta$-spondumene solid solution were formed. Generally, the densification and bending strength were increased by the addition of MgO, but the positive thermal coefficient was found in the case of MgO 10 wt% addition because of second phase and glassy phase.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.781-789
• /
• 1997

Pressure sintered SiC specimens were joined using MgO-Al2O3-SiO2 (MAS) glass which has a thermal expansion coefficient similar to that of SiC. MAS melt showed excellent behavior of wetting on the SiC substrate over 148$0^{\circ}C$, and the wettability was much influenced by the joining atmosphere. The joining was conducted at 150$0^{\circ}C$ for 30 min in Ar atmosphere. The flexural strength of the joined specimen shows 342~380 MPa up to 80$0^{\circ}C$, which is almost the same as that of as-recieved SiC specimen. However, the flexural strength of the joined specimen decreased to about 80 MPa at 90$0^{\circ}C$ due to softening of the glass melt. The analyses od XRD and WDS show that the reaction between the SiC specimen and the MAS melt produces the oxycarbide glass, which had a high strength and a good stability at high temperatures.

• 자원리싸이클링
• /
• 제20권3호
• /
• pp.55-61
• /
• 2011

금속급 실리콘(MG-Si)을 태양전지용 실리콘(SOG-Si)으로 정제하기 위한 경제적인 프로세스를 구축하기 위하여 1823 K에서 CaO-$SiO_2$ 계 슬래그에 의한 붕소의 제거에 대하여 조사하였다. 본 연구에서 CaO-$SiO_2$와 $CaCO_3-SiO_2$ 슬래그의 염기도(%CaO/$%SiO_2$) 증가에 따라 B의 제거율은 각각 63%와 73%까지 증가하였다. 그러나 Ar 가스에 의한 슬래그와 실리콘의 교반 시간의 영향은 나타나지 않았다. 그리고 CaO-$SiO_2$ 계 슬래그에 $Na_2CO_3$를 첨가하였으나 그 영향은 크지 않았다. $CaCO_3-SiO_2$ 슬래그(염기도=1.2)에 의해 3회 처리한 결과 B의 농도는 1.03 ppm까지 감소하였다.

• 한국주조공학회지
• /
• 제19권5호
• /
• pp.433-439
• /
• 1999

Rapidly solidified Mg-Al-Si base alloys containing Ca were obtained by melt spinning. The melt-spun ribbons were aged isochronally or isothermally to investigate age hardening phenomena and microstructural change according to the alloy composition. Age hardening occurred after aging at $200^{\circ}C$ for 1h mainly due to the precipitation of $Al_2Ca$ and $Mg_2Ca$, which have coherent interfaces with the matrix. With the increase of Ca content, the hardness values of the alloy ribbons were increased. Among the alloys, Mg-10Al-2 Si-3Ca alloy showed a good thermal stability at elevated temperature.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.193-193
• /
• 2003

• 한국결정성장학회지
• /
• 제7권4호
• /
• pp.658-664
• /
• 1997

자기질 도자기 소지조성에 필수적으로 함유되는 부산화물들($K_2O, MgO, CaO,Al_2O_3$, 그리고 $TiO_2$)이 순수한 $SiO_2$의 상형태에 미치는 영향을 조사하였다. 또한 장석, 도석, 카올린, 그리고 점토를 이용하여 조합된 자기질 도자기 소지 조성에서 $SiO_2/Al_2O_3$의 비를 조정하여 안정화된 $\beta$-cristobalite 상을 갖는 도자기 소지 조성을 개발하였으며, 여기에 첨가된 부산화물들이 $SiO_2$의 상형태에 미치는 영향을 조사하였다. $SiO_2$에 $K_2$O와 MgO를 첨가할 경우 준안정한 주상은 $\alpha$-cristobalite, CaO와 $Al_2$O$_3$를 첨가할 경우 $\alpha$-quartz, 그리고 $TiO_2$를 첨가할 경우는 비정질상이었다. 장석, 도석, 카올린, 그리고 점토를 사용하여 조합한 도자기 소지에서 $SiO_2/Al_2O_3$비가 작아질 수록 $\beta$-cristobalite 상의 안정화가 촉진되었으며, $\beta$-cristobalite 상이 안정화되는 임계의 $SiO_2/Al_2O_3$의 비는 68.10/22.75이었다. Cristobalite 상이 안정화된 실용 도자기 조성에 부산화물들이 첨가될 경우 $\alpha$, $\beta$-cristobalite 상생성이 억제되었다.