• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.39-43
• /
• 1997

Effects of B$_2$O$_3$ addition in the Li$_2$O-MgO-MgF$_2$-SiO$_2$g1ass system were investigated in order to make glass-ceramics for low temperature firing substrate. Base glass was made by melting at 145$0^{\circ}C$ . This glass was analyzed by THA and DTA to settle nucleation and crystallization temperature. After crystallization. crystal phase and microstructure were absorvated by XRD and SEM. Glass powders were made by water swelling method. Average particle size was 5.44${\mu}{\textrm}{m}$

• 한국세라믹학회지
• /
• 제46권2호
• /
• pp.189-199
• /
• 2009

The Powder characteristics and sintering behavior of $SiO_2$ coated $BaTiO_3$ were studied. $BaTiO_3$ powders were synthesized by the liquid mix method developed by Pechini, and silica coating was prepared by alkoxide hydrolysis method with TEOS and ethanol. The particle size of the $BaTiO_3$ powders was 35 nm and the thickness of the $SiO_2$ coating layer was 5 nm. As the $SiO_2$ content increased, the $SiO_2$ layers improved the powder dispersion by increasing electrostatic repulsion between the $BaTiO_3$ particles. Effects of MgO coating on microstructure and dielectric properties of $BaTiO_3$ have been studied compared with mechanically MgO mixed $BaTiO_3$. MgO coated $BaTiO_3$ particles were prepared by a homogeneous precipitation method using $MgCl_2\cdot 6H_2O$ and urea. MgO coated $BaTiO_3$ exhibited homogeneous microstructure compared with mixed samples. XRD analysis revealed that Mg substitution for the Ti site in the MgO mixed sample was much greater than in the coated one. Electrical properties of MgO mixed and coated $BaTiO_3$ were affected by the diffusion behavior of Mg in $BaTiO_3$ lattice.

• 동력기계공학회지
• /
• 제5권4호
• /
• pp.74-81
• /
• 2001

The infiltration behavior of molten Al-alloy, microstructures, hardness, and the interfacial reactions of $SiC_p/Al$ composites fabricated by the pressureless infiltration technique were investigated. It was made clear that both the weight fraction of SiC reinforcement and additive Mg content considerably influenced on the infiltration behavior of the molten Al-alloy matrix. Complete infiltration of molten Al-alloy achieved under the conditions that weight fraction of SiC content is more than 30wt%, and additive Mg content is more than 9wt%. Interfacial region of Al-alloy matrix and SiC reinforcement phase, $Mg_2Si$ was formed by the reaction between Mg and SiC. Another reaction product AlN was also formed by the reaction between Al-alloy matrix and gas atmosphere nitrogen.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권3호
• /
• pp.56-59
• /
• 2005

Aluminum alloy casting is gaining increased acceptance in automotive and electronic industries and especially, squeeze casting is the most efficient method of mass manufacturing of such parts. In this study, the microstructures and mechanical properties of Al-7.0Si-0.4Mg(AC4C) alloy fabricated by squeeze casting process for development of fuel system parts (fuel rail) are investigated. The microstructure of squeeze cast specimen was composed of eutectic structure aluminum solid solution and $Mg_2Si$ precipitates. The tensile strength of as-solid solution treatment Al-7.0Si-0.4Mg alloy was 298.5MPa. It was found that Al-7.0Si-0.4Mg alloy had good corrosion resistance in electrochemical polarization test.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.233-238
• /
• 2010

Hot-dipped Al-Mg-Si coatings to alternate Zn and Zn alloy coatings for steel were examined on metallographic structure, corrosion resistance, sacrificial ability, formation and growth of inter-metallic compounds, and mechanical properties. Near the eutectic composition of quasi-binary system of Al-$Mg_2Si$, very fine eutectic structure of ${\alpha}$-Al and $Mg_2Si$ was obtained and it showed excellent corrosion resistivity and sacrificial ability for a steel in sodium chloride solutions. Formation and growth of Al-Fe inter-metallic compounds at the interface of substrate steel and coated layer was suppressed by addition of Si. The inter-metallic compounds layer was usually brittle, however, the coating layer did not peel off as long as the thickness of the inter-metallic compounds layer was small enough. During sacrificial protection of a steel, amount of hydrogen into the steel was more than ten times smaller than that of Zn coated steel, suggesting to prevent hydrogen embrittlement. Al-Mg-Si coating is expected to apply for several kinds of high strength steels.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.18-21
• /
• 1995

In this study, crystallization, water swelling and dielectric properties of Li$_2$O-MgO-MgF$_2$-SiO$_2$System glass ceramics were investigated. Base glass melted at 1450$^{\circ}C$ and crystallized through heat treatment. The optimum heat treatment schedule was 460$^{\circ}C$ for nucleation and 640$^{\circ}C$, 1100$^{\circ}C$ for crystallization. The Principle crystalline phase was lithium fluorhectorite. Lithium fluorhectorite was the crystal phase which it was influenced water swelling. Samples progressed 2 minutes later they have rapid hydration at forced water swelling condition. Also value of dielectric constants have approximately 10 at 100kHz.

• 한국결정성장학회지
• /
• 제3권1호
• /
• pp.85-92
• /
• 1993

커다란 olivine 단결정을 image furnace(floating zone furnace)를 사용하여 산소분압의 조절하에서 성장시켰다. 결정은 투명하였으며 길이가 65mm, 직경이 8mm였다. 산소분압이 감소할 때 결정내 제2상이 증가하여 결정을 엷은 갈색에서 짙은 갈색으로 변화시켰다. 이 제2상은 EPMA결과 Mg가 기저를 이룬 것에 Si와 Fe가 solid solution을 형성한 것이었다.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.399-403
• /
• 1993

Si(111)7 $\times$ 7 위에 Mg를 흡착시켜 표면구조의 변화를 RHEED(Reflection High Energy Electron diffraction) 와 XPS(X-ray PhotoelectronSpectroscopy)를 이용하여 연구하였다. RT ~20$0^{\circ}C$까지의 기판온도에서 증착량의 증가에 따라 표면구조는 (7$\times$7)에서 diffused (1$\times$1) 그리고 (2 3 3 $\times$2√3√3-R30$^{\circ}$) 구조로 변화하였다. 또한, 기판온도를 증가시킴에 따라 (1$\times$1), three domain(3$\times$1) 등의 구조를 볼 수 있었고, 특히 , $450^{\circ}C$의 기판온도에서는 single domain (3$\times$1) 구조를 최초로 관측하였다. 이렇게 형성된 각 구조에 대한 Mg KLL과 Si2p의 XPS peak intensity ratio를 증착량의 증가에 따라 측정하여 각기 다른 온도에서의 Mg 성장에 대한 메카니즘을 제시하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.590-593
• /
• 1999

$Y_2SiO_5$:Ce was considered as blue phosphor for field emission display because it had an excellent resistance against brightness saturation. But unfortunately It hadn't a sufficient brightness to be applied to FED. In this experiment It-$In_2O_3$, MgO and $SiO_2$ were coated onto $Y_2SiO_5$:Ce phosphor in order to improve the cathodoluminance(CL properties. The coating structures were identified to be the crystalline phases of $In_2O_3$ and MgO respectively. They had fine particle-like shape and were distributed on the surface of $Y_2SiO_5$:Ce phosphor. It was found that the CL efficiency of $Y_2SiO_5$:Ce phosphors were decreased after coatings with In20:j and MgO in voltage range from 500 V to 5 kV. But the brightness of $Y_2SiO_5$:Ce phosphor was increased after coating of 5 0 2 . And also the aging test showed that $In_2O_3$ coating improved the life time of $Y_2SiO_5$:Ce phosphor.

• 생태와환경
• /
• 제35권3호통권99호
• /
• pp.213-219
• /
• 2002

녹조 제어를 위하여 수중의 인 제거에 관여하는 CellCaSi의 여러 가지 조건별 인 제거효과를 조사하였다. CellCaSi의 입도에 따른 인 제거효과는 직경 1, 2 그리고 4mm 이하의 3가지 중 1mm 이하의 작은 입자를 사용했을 때 가장 우수하였다. CellCaSi의 인 제거효과는 처리량의 증가에 비례하였다. 수중의 pH 5, 7, 9에서 초기 인 농도 0.20mg/l는 각각 0.09, 0.08및 0.08mg/l로 감소되어 상이한 pH조건에 따른 CellCaSi의 인 제거효과는 큰 차이를 보이지 않았다. CellCaSi에서 용출되는 양이온은 Ca이며, Al과 Fe양이온은 검출되지 않았다. 초기에 급격히 용출된 Ca양이온은 수중의 인과 반응하는 것으로 확인되었다. 초기 인 농도 0.10, 1.0mg/1는 CellCaSi와 Ca, Fe 화합물을 첨가한 처리구에서 8일 후 각각 0.03,0.47mg/l를 기록하며 가장 많이 감소하였다. 이에 따라 인 제거효과는 CellCaSi와 Ca, Fe 화합물을 동시에 처리하였을 때 가장 좋은 것으로 조사되었다. CellCaSi의 처리에 따라 pH가 약간 증가하였고, 전기전도도도 증가되지만 상수원수 기준 허용치 (500${\mu}$S/cm) 이내였다.