• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.2
• /
• pp.108-121
• /
• 2009

The suspended particulate matters have been collected on membrane filters and glass fiber filters by an 8-stage cascade impactor for 2 years (Sep. 2005${\sim}$Sep. 2007) in Kyung Hee University-Global Campus located on the border of Yongin and Suwon. The 20 chemical species (Al, Mn, Si, Fe, Cu, Pb, Cr, Ni, V, Cd, Ba, $Na^+$, ${NH_4}^+$, $K^+$, $Mg^{2+}$, $Ca^{2+}$, $Cl^-$, ${NO_3}^-$, and ${SO_4}^{2-}$) were analyzed by an ICP-AES and an IC after performing proper pre-treatments of each sample filter. Based on these chemical information, the PMF receptor model was applied to identify the source of ambient size-by-size particulate matters. The receptor modeling is the one of the statistical methods to achieve resonable air pollution management strategies. A total of 10 sources was identified in 9 size-ranges such as long-range transport, secondary aerosol, $NH_{4}NO_{3}$ related source, coal combustion, sea-salt, soil, oil combustion, auto emission, incineration, and biomass burning. Especially, the secondary aerosol source assorted in fine and coarse modes was intensively studied.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.745-752
• /
• 2012

This paper studies the effect of the compressive strength for combined alkali-activated slag mortars. The effect of activators such as alkali type and dosage factor on the strength was investigated. The alkalis combinations made using five caustic alkalis (sodium hydroxide (NaOH, A series), calcium hydroxide ($Ca(OH)_2$, B series), magnesium hydroxide ($Mg(OH)_2$, C series), aluminum hydroxide ($Al(OH)_3$, D series), and potassium hydroxide (KOH, E series)) with sodium carbonate ($Na_2CO_3$) were evaluated. The mixtures were combined in different dosage at 1M, 2M, and 3M. The study results showed that the compressive strength of combined alkali-activated slag mortars tended to increase with increasing sodium carbonate. The strength of combined alkali-activated slag mortars was better than that of control cases (without sodium carbonate). The result from scanning electron microscopy (SEM) analysis confirmed that there were reaction products of calcium silicate hydrate (C-S-H) and alumina-silicate gels from combined alkali-activated slag specimens.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.174-174
• /
• 2009

현재 전자부품용으로 사용되는 유리프리트의 경우 PbO계를 주로 사용하고 있다. 최근 환경규제에 따른 PbO 사용이 제한됨에 따라 이를 대체할 Pb-free 유리 조성에 대한 연구가 활발히 진행 중이다. Pb-free계로서는 $Bi_2O_3$계, $B_2O_3$계가 주로 연구되고 있으나 소성 온도가 $500^{\circ}C$이상으로 높고 또한 $Bi_2O_3$ 계는 중금속이기 때문에 문제가 있다. 본 연구에서는 $400^{\circ}C$ 미만 소성이 가능한 SnO-$P_2O_5$계를 기본 조성계로 선택하고 열적, 전기적, 화학적 특성을 개선하기 위해 $R_2O_3$(R=Al, B), RO(R=Mg, Zn, Ca, Ba) 를 첨가하였다. 개선된 조성으로 샘플을 만들고 이를 대상으로 실제 전자부품 생산 공정에 적용 실험을 진행 하였다. 실험에 사용된 전자 부품은 소형 칩 베리스터로 생산 공정에서 코팅용 유리프리트와 파우더를 절연체로서 전면에 코팅하게 된다. 유리프리트를 코팅함으로서 누설 전류를 차단하고 생산 공정시 베리스터 내부를 보호하게 된다. 실험에 사용된 샘플의 열적 특성은 TMA로, 전기적 절연 특성은 고 절연저항 측정기로 측정하였고 내 산성과 내 알칼리성도 측정하였다. 샘플을 이용하여 완성된 칩 베리스터의 성능은 고온, 내습 신뢰성 TEST(고온:$150^{\circ}C$ 12HR, 내습:$85^{\circ}C$-85%12HR)로 실험하여 합부판정 (Leakage current <10uA)을 내려 완성품과 불량품을 가려내었다.

• 한국지구과학회:학술대회논문집
• /
• 2005.09a
• /
• pp.136-141
• /
• 2005

The K Ar ages, whole rock geochemistry and Sr Nd Pb isotopes have been determined for the submarine basalts dredged from the P2 and P3 segments of the Antarctic-Phoenix Ridge (APR), Drake Passage, Antarctica, for better understanding on temporal variation of magma chemistry in association with extinction of seafloor spreading. The fossilized APR is distant from the known hot spots, and consists of older N-MORB prior to extinction of spreading and younger E-MORB after extinction. The older N-MORB (3.5-6.4 Ma) occur in the southeast flank of the P3 segment (PR3) and the younger E-MORB (1.4-3.1 Ma) comprise a huge seamount at the P3 segment (SPR) and a big volcanic edifice at the P2 segment (PR2). The N-type PR3 basalts have higher Mg#, K/Ba, and CaO/Al2O3 and lower Zr/Y, Sr, and Na8.0 with slight enrichment in incompatible elements and almost flat REE patterns. The E-type SPR and PR2 basalts are highly enriched in incompatible elements and LREE. The extinction of spreading occurring at 3.3 Ma seems to have led to a temporal magma oversupply with E-MORB signatures. Geochemical signatures such as Ba/TiO2, Ba/La, and Sm/La suggest heterogeneity of upper mantle and formation of E-MORB by higher contribution of enriched materials to mantle melting, compared to N-MORB environment. E-MORB magmas beneath the APR seem to have been produced by low melting degree (up to 1% or more) at deeper low-temperature regime, where metasomatized veins consisting of pyroxenites have preferentially participated in the melting. The occurrence of E-MORB at the APR is a good example to better understand what kinds of magmatism would occur in association with extinction of spreading.

• Nutrition Research and Practice
• /
• v.8 no.4
• /
• pp.360-367
• /
• 2014

BACKGROUND/OBJECTIVES: The aim of this research was to study the different long term effects of consumption of dietary oil sources with varying omega-6/omega-3 (${\omega}-6/{\omega}-3$) polyunsaturated fatty acids (PUFAs) ratios on bone marrow fatty acid level, ex vivo prostaglandin $E_2$ ($PGE_2$) release, and mineral content of bone in rabbits. MATERIALS/METHODS: For this purpose, weaning and female New Zealand white rabbits were purchased and randomly divided into five groups and offered ad libitum diets containing 70 g/kg of added oil for 100 days. The dietary lipid treatments were formulated to provide the following ratios of ${\omega}-6/{\omega}-3$ fatty acids: 8.68 soy bean oil (SBO control), 21.75 sesame oil (SO), 0.39 fish oil (FO), 0.63 algae oil (DHA), and 0.68 algae oils (DHA/ARA). DHA and ARA are two types of marine microalgae of the genus Crypthecodinium cohnii. RESULTS: The dietary treatments had significant effects on the bone marrow fatty acids of rabbits. Rabbits fed the FO diet, containing the highest ${\omega}-3$ PUFA concentration, and those fed the SBO diet showed the highest ${\omega}-6$ PUFA. On the other hand, a positive correlation was observed between Ex vivo $PGE_2$ level and the ${\omega}-6/{\omega}-3$ dietary ratio. Significant effects of dietary treatment on femur Ca, P, Mg, and Zn contents were observed in both genders. CONCLUSIONS: Findings of the current study clearly demonstrated that dietary PUFA, particularly ${\omega}-6/{\omega}-3$ and ARA/EPA ratios are important factors in determining bone marrow fatty acid profile, and this in turn determines the capacity of bone for synthesis of $PGE_2$, thereby reducing bone resorption and improving bone mass during growth.

• Economic and Environmental Geology
• /
• v.3 no.1
• /
• pp.17-24
• /
• 1970

The purpose of this report is to prepare a data for the economic evaluation on the Goobong Limestone Mine which is located at the south-eastern corner of the Yongchun Quadrangle scaled in 1:50,000. The accessibility from the mine to railroad was considered in two ways. One is to Dodam Station on Central Railway Line and the other is to reach Songjung-ni village which is near Sangyong Station on Hamback Railway Line. The distance of the former way is 26.7km and the later is 24.2km. Geologically the mine is situated near the base of the Greast Limestone Series which strikes generally $N25^{\circ}{\sim}30^{\circ}E$. The series comprises six different formations from older to younger; Pungchon Limestone Formation and Whajol Formation of Cambrian age, and Dongjum Quartzite Formation, Dumudong Formation, Maggol Limestone Formation and Goseong Formation of lower to middle Ordovician age. 82 samples; 48 from Pungchon Limestone Formation, 11 from Dumudong Formation, 15 from Maggol Limestone Formation and 8 from Goseong Formation, were taken from the series in the crossed direction to the general trend of the series as shown in geological map. They were chemically analyzed on the components of CaO, MgO, $SiO_2$, $R_2O_3(Al_2O_3+Fe_2O_3)$ and ignition loss as shown in table 2, table 3, table 4, and table 5. As seen from the tables, among the formations of the series, middle to upper parts of the Pungchon Limestone Formation and middle and upper parts of the Dumudong Formation have chemical composition as available source for the raw material of cement industry, not only that but also the part of the Pungchon Formation was highly evaluated as source for the flux of iron smelting and the raw material of carbide manufacturing because of its high purity of calcium carbonate.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.2
• /
• pp.165-175
• /
• 1996

Fourteen(14) large commercial buildings located in Seoul with friable sprayed-on surface insulation material on ceiling were investigated for fiber types in bulk material and for airborne fiber concentrations in buildings by transmission electron microscopy (TEM) in order to compare the results with those by polarized light microscopy (PLM) and phase contrast microscopy (PCM). The results were as follows: 1. Chrysotile asbestos was found in one bulk sample out of total 14 bulk samples collected. Glass fiber and mineral wool were the two major constituents of the bulk samples. 2. The Na-Mg-Si-Ca-Fe-Al ratios of the EDX spectra which were normalized with the Si peak were 0-1.0-10-8.3-4.0-4.0 in mineral wool and 0-5-10-21-0-0 in chrysotile asbestos, respectively. 3. Airborne fiber concentrations were log-normalcy distributed and the geometric mean (geometric standard deviation) fiber concentrations by TEM in the underground parking lots and inside buildings were 0.0048 f/cc(1.93) and 0.0040 f/cc(2.27), respectively with no statistical difference. In the outdoor ambient air, statistically significantly lower concentration of 0.0018 f/cc(2.04) was measured. 4. The TEM/PCM ratios of airborne fiber concentrations ranged 0.5 - 2.0 for 80 % of airborne samples analyzed, end the regression equation between TEM and PCM was PCM=-0.2724+1.1355(TEM) with the coefficient of determination $R^2=0.52$. The results of this study confirmed that the sprayed-on surface insulation material found in some commercial buildings may possibly be contaminated with asbestos fiber. Since statistically significant relationship of fiber concentrations measured by PCM and TEM inside buildings and ambient air was found, previous results by PCM in ambient air could be used to estimate the ambient fiber concentrations in knowing the ratio of TEM/PCM.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.101-108
• /
• 2005

Because the stone cultural properties located outdoors, they have been altered and deteriorated in external appearance due to environmental factors such as acid rain, extreme change in temperature, and salts. Damage to stone cultural properties is accelerated particularly due to recent industrial development and environmental pollution. An experimental study was conducted to evaluate the effect of environmental contaminants on the weathering of granite. And as part of the developing of conservation method, $TiO_2$ catalyst was prepared and tested. When fresh granite was dipped into the salt and acid solutions, dissolution rate of eight minerals (Si, Mg, Ca, Na, K, Fe, Mn, Al) are abruptly increased at initial stage of reaction and then increased steadily until 100 cycles. After salt and acid solution experiments, the mineral compositions of the granite surface were lower then that of the fresh granite and density of the weathered granite was steadily decreased from $2.60\;g/cm^3$ to $2.56\;g/cm^3$, but Poissions ratio and absorption ratio were slightly increased. It was expected at stone cultural assets could be weathered by salts and acid rain. In the case of $TiO_2$ was coated to the granite, the dissolution rate of minerals and absorption ratio of $TiO_2$ coated granite were decreased. Therefore, the $TiO_2$ coating method tested in this study considered to be a viable method to assist in the conservation of stone cultural properties from environmental contaminants.

• Asian Journal of Atmospheric Environment
• /
• v.8 no.3
• /
• pp.126-139
• /
• 2014

In order to estimate the influence of sources on $PM_{2.5}$ in the industrial area of Japan, we carried out a source analysis using chemical component data of $PM_{2.5}$. $PM_{2.5}$ samples were collected intermittently at an industrial area in Japan from July 2010 to November 2012. Water soluble ions ($Cl^-$, $NO_3{^-}$, $SO{_4}^{2-}$, $Na^+$,$NH_4{^+}$, $K^+$, $Mg^{2+}$, $Ca^{2+}$), elements (Al, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Cd, Sb, Pb), and carbonaceous species (OC, EC) of the $PM_{2.5}$ (a total of 198 samples) were analyzed. Positive Matrix Factorization (PMF) model was applied to the data of those chemical components to identify the source of $PM_{2.5}$. At this observation site, nine factors were extracted. The major contributors of $PM_{2.5}$ were secondary sulfate 1, in which loading factors of $SO{_4}^{2-}$ and $NH_4{^+}$ were large (percentage source contribution: 20.9%), traffic, in which loading factors of OC (organic carbon) and EC (elemental carbon) were large (20.8%), secondary sulfate 2, in which loading factors of K and $SO{_4}^{2-}$ were large (8.0%), steel mills (7.8%), secondary chloride and nitrate (7.0%), soil (5.0%), heavy oil combustion (3.8%), sea salt (3.8%), and coal combustion (2.3%). The conditional probability function (CPF) and the potential source contribution function (PSCF) were carried out to examine the influence of a regional source and a broad-based source, respectively. CPF results supported local source influences such as steel mills, sea salt, traffic, coal combustion, and heavy oil combustion. PSCF results suggested that ships in the East China Sea, an industrial area of the east coastal region of China, and an active volcano in the Kyushu region of Japan were potential regional sources of secondary sulfate 1. Secondary sulfate 2 was affected by the burning of biomass fields and by coal combustion in Chinese urban areas such as Beijing, Hebei, and western Inner Mongolia. Source characterization using continuous data from one site showed a potential source representing fossil fuel combustion is affected both by regional and broad-based sources.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.18 no.1
• /
• pp.40-46
• /
• 2013

The isotope ratios of $^{13}C/^{12}C$ and $^{18}O/^{16}O$ for a sample in a mass spectrometer are measured relative to those of a pure $CO_2$ reference gas (i.e., laboratory working standard). Thus, the calibration of a laboratory working standard gas to the international isotope scales (Pee Dee Belemnite (PDB) for ${\delta}^{13}C$ and Vienna Standard Mean Ocean Water (V-SMOW) for ${\delta}^{18}O$) is essential for comparisons between data sets obtained by other groups on other mass spectrometers. However, one often finds difficulties in getting well-calibrated standard gases, because of their production time and high price. Additional difficulty is that fractionation processes can occur inside the gas cylinder most likely due to pressure drop in long-term use. Therefore, studies on laboratory production of pure $CO_2$ isotope standard gas from stable solid calcium carbonate standard materials, have been performed. For this study, we propose a method to extract pure $CO_2$ gas without isotope fractionation from a solid calcium carbonate material. The method is similar to that suggested by Coplen et al., (1983), but is better optimized particularly to make a large amount of pure $CO_2$ gas from calcium carbonate material. The $CaCO_3$ releases $CO_2$ in reaction with 100% pure phosphoric acid at $25^{\circ}C$ in a custom designed, evacuated reaction vessel. Here we introduce optimal procedure, reaction conditions, and samples/reactants size for calcium carbonate-phosphoric acid reaction and also provide the details for extracting, purifying and collecting $CO_2$ gas out of the reaction vessel. The measurements for ${\delta}^{18}O$ and ${\delta}^{13}C$ of $CO_2$ were performed at Seoul National University using a stable isotope ratio mass spectrometer (VG Isotech, SIRA Series II) operated in dual-inlet mode. The entire analysis precisions for ${\delta}^{18}O$ and ${\delta}^{13}C$ were evaluated based on the standard deviations of multiple measurements on 15 separate samples of purified $CO_2$. The pure $CO_2$ samples were taken from 100-mg aliquots of a solid calcium carbonate (Solenhofen-ori $CaCO_3$) during 8-day experimental period. The multiple measurements yielded the $1{\sigma}$ precisions of ${\pm}0.01$‰ for ${\delta}^{13}C$ and ${\pm}0.05$‰ for ${\delta}^{18}O$, comparable to the internal instrumental precisions of SIRA. Therefore, we conclude the method proposed in this study can serve as a way to produce an accurate secondary and/or laboratory $CO_2$ standard gas. We hope this study helps resolve difficulties in placing a laboratory working standard onto the international isotope scales and does make accurate comparisons with other data sets from other groups.