• Journal of the Korean Electrochemical Society
• /
• v.6 no.1
• /
• pp.41-47
• /
• 2003

For the development of low temperature anode-supported planar solid oxide fuel cell, the planar anode supports with the thickness of 0.8 to 1 mm and the area of 25, 100 and $150\;cm^2$ were fabricated by the tape casting method. The strength, porosity, gas permeability and electrical conductivity of the planar anode support were measured. The porosity of anode supports sintered at $1400^{\circ}C$ and then reduced in$H_2$ atmosphere was increased from $45.8\%\;to\;53.9\%$. The electrical conductivity of the anode support was $900 S/cm\;at\; 850^{\circ}C$ and its gas permeability was 6l/min at 1 atm in air atmosphere. The electrolyte layer and cathode layer were fabricated by slurry dip coating method and then had examined the thickness of $10{\mu}m$ and the gas permeability of 2.5 ml/min at 3 atm in air atmosphere. As preliminary experiment, cathode multi-layered structure consists of LSM-YSZ/LSM/LSCF. At single cell test using the electrolyte layer with thickness of 20 to $30{\mu}m$, we achieved $300\;mA/cm^2$ and 0.6V at $750^{\circ}C$

• Korean Journal of Ecology and Environment
• /
• v.42 no.3
• /
• pp.382-393
• /
• 2009

The objectives of this study were to characterize long-term annual and seasonal trophic state of Topjeong Reservoir using conventional variables of Trophic State Index (TSI) and to determine the empirical relations between the trophic parameters. For the analysis, we used water quality dataset of 1995$\sim$2007, which is obtained from the Ministry of Environment, Korea and the number of parameters was 9. Annual ambient mean values of TN and TP were 1.78 mg $L^{-1}$ and 0.03 mg $L^{-1}$, respectively and TN : TP ratios averaged 76, indicating that this system was nitrogen-rich hypertrophic, and was probably phosphorus-limitation for algal growth. Therefore, nitrogen varied little with seasons and years, and total phosphorus (TP) varied depending on season and year. Monsoon dilutions of TP occurred in August and monthly fluctuations of suspended solid (SS) was similar to those of chlorophyll-$\alpha$ (CHL). Annual mean values of BOD and $COD_{Mn}$ were 1.61 mg $L^{-1}$ and 4.23 mg $L^{-1}$, respectively and the interannual values were directly influenced by the intensity of annual rainfall. There were no significant differences in the trophic variables between the two sampling sites. Mean values of Trophic State Index (TSI, Carlson, 1977), based on TN, TP, CHL, and SD (Secchi depth), turned out as eutrophic state, except for the TN (hypertrophic). Regression analyses of log-transformed seasonal CHL against TP and TN showed that variation of the CHL was explained 37% by the variation of TP ($R^2$=0.37, p<0.001, r=0.616), but not by TN ($R^2$=0.03, p>0.05). Regression coefficient of $Log_{10}$CHL vs $Log_{10}SD$ was 0.330 (p<0.003, r=0.580), indicating that transparency is regulated by the organic matter in the system. Results, data suggest that one of the ways controlling the eutrophication would be a reduction of phosphorus from the watershed.

• Applied Biological Chemistry
• /
• v.49 no.4
• /
• pp.322-327
• /
• 2006

Food constituents analysis of Acer tegmentosum. Maxim.(Acer TM) stem was carried out according to AOAC method, and the antiradical activity on DPPH and cytotoxicity on human cell lines (AGS, HepG2, A549, MCF-7 and Chang) for the 80% ethylalcohol(EtOH) extracts of Acer TM stem were studied. The antiradical activity on DPPH radical of the ethylacetate(EtOAc) fraction of the bark showed a higher activity than that of $\alpha$-tocopherol, ascorbic acid and BHT. The inhibition activity of the 80% EtOH extracts from Acer TM stem on human cancer cell lines by SRB assay indicated a dose-dependent growth inhibition on most human carcinoma cells. The growth inhibition rate of each human cancer cell line showed 91.3% to AGS, 75.0% to A549, 74.1% to HepG2, and 70.2% to MCF-7 cells, respectively, when the 80% EtOH extract(1 mg/ml) of Acer TM stem was added.

• Journal of Sericultural and Entomological Science
• /
• v.13 no.1
• /
• pp.49-59
• /
• 1971

This experiment was conducted, how making use of "Seracol 100", a kind of nonionic surface active reagent, during cocoon cooking and silk reeling process which is mainly used in Korea and developed by one of the authors since 1965. Main purpose of the experiment is to investigate the influence of the activity of the reelability aid reagent on various degree of hardness component and various salts which are contained in filature water being used by silk factories now. Specifically, it was tried to determine the effects of the reelability aid reagent added to each sample water of artificially differentiated the degree of hardness component upon sericin solubility. Some of the major findings are summarized as follows. 1. "Seracol 100", with below 5$^{\circ}$dH water, increased sericin solubility in each sample water, but above $10^{\circ}$dH the effect of it shows a significant relationship with the different degree of hardness component. Besides the component (MgCO$_3$)$_4$ㆍMg(OH)$_2$, generally, the higher the degree of hardness in the water, the less the amount of desolved sericin in the water showed. There is little or no difference between 1000 times diluted "Seracol 100" water and 2000 times diluted "Seracol 100" water in terms of sericin solubility. 2. The different kind of degree of hardness component shows a significant relationship with sericin solubility, In case use of "Seracol 100", Mg hardness component affected on the sericin solubility more than Ca hardness. But in the control, contrary to this, that is Ca hardness component did more than Mg hardness, 3. The different kind of salts in degree of hardness component show a significant relationship with sericin solubility. In the control water, nitrate is the greatest among salts affecting on sericin solubility, next chloride and sulfate are in order. In case of "Seracol 100" water, chloride is the least among salts, below $10^{\circ}$dH, next sulfate and nitrate are in order, and above 15$^{\circ}$dH, next nitrate and sulfate are in order. 4. In case of "Seracol 100" water, the more contained heavy metal salts (Fe, Al, Cu, Mn) in the water, the less sericin solubility showed. It is found that there is little or no difference among other salts in terms of sericin solubility. But alkaline metal salt remarkably increased sericin solubility. 5. In case of "Seracol 100" water, tinting of the water was affected by Ca salts more than by Mg salts. Among other salts, only Al and Fe affected on the tinting of the water, specifically, in view of the fact that "Seracol 100" water increase the tinting of Fe salt water, but decrease the tinting of raw silk. It is thought that "Seracol 100" deter Fe$^{+2}$ from absorbing to raw silk by deteriorating the activity of Fe$^{+2}$ . 6. "Seracol 100" have the effect on osmosis of the water, After treatment until 2hrs the osmosis of 1000 times diluted "Seracol 100" water is the greatest, next orders are 2000 times diluted "Seracol 100" and control. From 2 hrs to 6 hrs the osmosis of 2000 times diluted water is the greatest, next orders are 1000 times diluted water and control. After 6 hrs the osmosis of the water is the same order as above. 7. In view of tile fact that "Seracol 100" have the effect to control the degree of hardness during the treatment of cocoon layer in the water, it is thought that, in varying degree of hardness in the water, there is a significant relationship between "Seracol 100" and degree of hardness components in cocoon layer.

• Korean Journal of Materials Research
• /
• v.6 no.7
• /
• pp.700-708
• /
• 1996

Electroless plating technique was utilized to flip chip bonding to improve surface mount characteristics. Each step of plating procedure was studied in terms pf pH, plating temperature and plating time. Al patterned 4 inch Si wafers were used as substrstes and zincate was used as an activation solution. Heat treatment was carried out for all the specimens in the temperature range from room temperature to $400^{\circ}C$ for $30^{\circ}C$ minutes in a vacuum furnace. Homogeneous distribution of Zn particles of size was obtained by the zincate treatment with pH 13 ~ 13.5, solution concentration of 15 ~ 25% at room temperature. The plating rates for both Ni-P and Au electroless plating steps increased with increasing the plating temperature and pH. The main crystallization planes of the plated Au were found to be (111) a pH 7 and (200) and (111) at pH 9 independent of the annealing temperature.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3293-3301
• /
• 1974

An experimental work was conducted by using a laboratory-made model dryer to investigate the effect of the rate of natural forced-air on the drying rate of rough rice which was deposited in the deep-bed. The dryer consisted of 8 cylinderical containers with grain holding screen at their bottoms, each of which having 30cm in diameter and 15cm in height. The containers were sacked vertically with keeping them air-tight by using paper tape during dryer operation. Two separate layers of containers were operated in the same time to have two replications. The moisture contents of grains within each bins after predetermined period of dryer operation were determined indirectly by measuring the weight of the individual containers. The air-rates were maintained at 6 levels, or 5, 8, 10, 15, 18 and 20 millimenters of static head of water. The roomair conditions during dryer operation were maintained in the range of 10-l5$^{\circ}C$ in temperature and 40-60% in relative humidity. The results of the study are summarized as follows: 1. Drying characteristics of the grains in the bottom layers were approximately the same regardless of airdelivery rates, giving the average drying rate as about 0.35 percent per hour after 40-hour drying period, during which moisture content (w. b.) reduced from 24 percent to about 10 percent. 2. After about 40-hour drying period, the mean drying rates increased from 0.163 percent per hour to 0.263 percent per hour as air-flow rates increased from 5mm to 87.16mm of static head of water. In the same time, the moisture differences of grains between lower and upper layers varied from 12.7 percent at the air rate of 5mm of water head to 7.5 percent at the air-flow rate of 20mn of water head. Thus, the greater the air-flow rate was, the more overall improvement in drying performance was. Additionally, from the result of ineffectiveness of drying grain positioned at 70cm depth or above by the air rate of 5mm of static head of water it may be suggested in practical application that the height of grain deposit would be maintained adequately within the limits of air-rates that may be actually delivered. 3. Drying after layer-turning operation was continued for about 30 hours to test the effectiveness of reducing moisture differences in the thick layers. As a result of this layer-turning operation, moisture distribution through layers approached to narrow ranges, giving the moisture range as about 7 percent at air-flow rate of 5mm head of water, about 3 percent at 10mm head about 2 percent at 15mm head, and less than 1 percent at 20mm head. In addition, from the desirable results that drying rate was rapid in the lower layers and dully in the upper layers, layer-turning operation may be very effective in natural air drying with deep-layer grain deposit, especially when the forced air was kept in low rate. 4. Even though the high rate of air delivery is very desirable for deep-layer natural-air drying of rough rice, it can be happened that the required air delivery rate could not be attained because of limitation of power source available on farms. To give a guide line for the practical application, the power required to perform the drying with the specified air rate was analyzed for different sizes of drying bin and is given in Table (5). If a farmer selects a motor of which size is 1 or {{{{1 { 1} over {2 } }}}} H.P. and air-delivery rate which ranges from 8~10mm of head, the diameter of grain bin may be suggested to choose about 2.4m, also power tiller or other moderate size of prime motor may be recommended when the diameter of grain bin is about 5.0m or more for about 120cm grain deposit.

• Journal of Animal Science and Technology
• /
• v.46 no.4
• /
• pp.625-634
• /
• 2004

The objective of this experiment is to study the possibility of lactate dehydrogenase(LDH) enzyme to prevent lactate accumulation in the rumen, For understanding capacity of bacterial LDH in rumen environments, this study was conducted to explore the effects of temperature, pH, VFAs and metal ions on Lactobacillus sp. FFy111-1's LDH activity, and the LDH activation in rumen fluid accumulated lactate. The optimum pH and temperature of LDH were pH 7.5 and 40$^{\circ}C$, respectively. The LDH activity had a good thennostability at range from 30 to 50$^{\circ}C$. The highest pH stability of the enzyme was at ranges from pH 7.0 to 8.0 and the enzyme activities showed above 64% level of non-treated one at pH 6.0 and 6.5. The LDH was inactivated by VFAs treatments but was enhanced by metal ion treatments without NaCl and $CuSO_4$ Especially, the LDH activity was increased to 127% and 124% of its original activity by 2 mM of $BaCl_2$ and $MnSO_4$, addition, respectively. When the acidic rumen fluid was treated by LDH enzyme of Lactobacillus sp. FFy111-1, the lactate concentration in the rumen fluid was lower compared with non-treated rumen fluid(P<0.05). This lactate reduction was resulted from an action of LDH. It was proved by result of purified D,L-LDH addition that showed the lowest lactate concentration among the treatments(P<0.05). Although further investigation of microbial LDH and ruminal lactate is needed, these findings suggest that the bacterial LDH has the potential capability to decrease the lactate accumulated in an acidic rumen fluid. Also, screening of super LDH producing bacteria and technical development for improving enzyme activity in rumen environment are essential keys for practical application.

• Applied Biological Chemistry
• /
• v.38 no.2
• /
• pp.141-146
• /
• 1995

Changes of physicochemical properties of citron juice prepared by two different extraction methods, rotary-crushing and belt-pressing method, were investigated during the storage at $5^{\circ}C$ and $-20^{\circ}C$. Temperature drop of citron juice extracted by belt-pressing method was faster than that of citron juice prepared by rotary-crushing method and its freezing point was $0.8{\sim}0.9^{\circ}C$. During the storage, pH of stored citron juice with rotary-crushing method was increased up to 3.5 after 6 months storage while that of citron juice extracted by belt-pressing method was not changed significantly during the same storage time. Acidity of rotary-crushed citron juice was reduced a little more than that of belt-pressed citron juice during the storage. However, changes of soluble solid content were influenced largely by the storage temperature than by the extraction method. Contents of formol nitrogen and vitamin C were reduced remarkably in all of stored citron juice and $92{\sim}82%$ of farmol nitrogen and $72{\sim}43%$ of vitamin C were remained after 6 months of storage. Among the changes of color value, L values were reduced in the whole stored citron juice and a and b value had a different change pattern respectively according to the extraction and storage temperature. Changes in the content of both amino acid and fatty acid compositions was also observed after same storage period. Especially, in the case of change of fatty acid composition, content of linoleic acid and linolenic acid were reduced after 6 months storage, while those of palmitic acid, stearic acid and oleic acid were increased.

• Korean Journal of Environmental Agriculture
• /
• v.2 no.2
• /
• pp.98-102
• /
• 1983

The hydrogen fluoride gas generated from making the cement hardener injured the plants growing at the neighbour field. This investigation was conducted on sample analysis of hydrogen fluoride gas damage plants which included the ratios of destroyed leaves, damage symptoms, and nutrient elements in paddy rice and weeds. The results obtained were as follows; 1) The ratio of destroyed leaves at near HF source was very high reaching about 95% at 100m, 65% at 500m, 5% at 2㎞, respectively. 2) The necrosis was the characteristic symptom of fluoride injury on rice plant and occurred predominantly at the tip and margins of damage leaf. It developed along the tip and margins of leaves with a dull, gray-green, water soaked discoloration. 3) The fluorine content of tip and margins of damaged rice leaves were 1,600 ppm, 3 to 20 times higher than that of center part and it ranged from 130 to 242.5 ppm in weed leaves, but from 10 to 15 ppm in normal weed leaves. 4) The contents of calcium, potassium, silicon, iron and manganese were higher in tip and margins than in the center of rice damage leaves. 5) The Cocculus trilolous. D.C was the most resistant plant to HF gas than any other plant growing in this site, while wild berry and aralia tree belong to most sensitive plant group.

• Proceedings of the KACD Conference
• /
• 2008.05a
• /
• pp.246-257
• /
• 2008

The purpose of this study was to investigate the influence of various occlusal loading sites and directions on the stress distribution of the cervical composite resin restorations of maxillary second premolar, using 3 dimensional (3D) finite element (FE) analysis. Extracted maxillary second premolar was scanned serially with Micro-CT (SkyScan1072; SkyScan, Aartselaar, Belgium). The 3D images were processed by 3D-DOCTOR (Able Software Co., Lexington, MA, USA). HyperMesh (Altair Engineering. Inc., Troy, USA) and ANSYS (Swanson Analysis Systems. Inc., Houston, USA) was used to mesh and analyze 3D FE model. Notch shaped cavity was filled with hybrid (Z100, 3M Dental Products, St. Paul, MN, USA) or flowable resin (Tetric Flow, Viva dent Ets., FL-9494-Schaan, Liechtenstein) and each restoration was simulated with adhesive layer thickness ($40{\mu}m$). A static load of 200 N was applied on the three points of the buccal incline of the palatal cusp and oriented in $20^{\circ}$ increments, from vertical (long axis of the tooth) to oblique $40^{\circ}$ direction towards the buccal. The maximum principal stresses in the occlusal and cervical cavosurface margin and vertical section of buccal surfaces of notch-shaped class V cavity were analyzed using ANSYS. As the angle of loading direction increased, tensile stress increased. Loading site had little effect on it. Under same loading condition. Tetric Flow showed relatively lower stress than Z100 overall, except both point angles. Loading direction and the elastic modulus of restorative material seem to be important factor on the cervical restoration.