• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.73-76
• /
• 1997

A low loss x-cut LiNbO$_3$ optical waveguide was fabricated by Ti in-diffusion and the guided-mode properties and total insertion loss of pigtailing with polarization maintaining fiber(PMF) were investigated and measured at optical wavelength 15507. For formaing the waveguide, the parameters of diffusion Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set 1400$\AA$, 8${\mu}{\textrm}{m}$, 3.3cm, 105$0^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. and then After the polishing and pigtailing, it showed that total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, horizontal/vertical sizes were 13.87/18${\mu}{\textrm}{m}$ for TM mode, 9.61${\mu}{\textrm}{m}$/6.5${\mu}{\textrm}{m}$ for TE mode.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.547-554
• /
• 2004

We investigated a LiNbO$_3$ based integrated-optic polarization controller with the Ti-indiffused waveguide along the z-axis utilizing the electro-optic effect. The device consists of a first quarter-wave (λ / 4) followed by a half-wave (λ / 2) and a second quarter-wave (λ / 4) wave-plate. We analyzed the amount of phase change and the transformation of the polarized mode as a function of the combination of wave-plates and of their applied voltages. The operation has been systematically measured utilizing a polarimeter and Poincare sphere. We confirmed that the fabricated device controls the transformations from any arbitrary input state of polarization (SOP) into any general output SOP.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.32-37
• /
• 2002

Passive polarization mode splitters at λ= 1.55 ${\mu}{\textrm}{m}$ were designed and fabricated based on Ti:x-cut LiNbO$_3$ single-mode optical waveguide and two-mode interference theory. The splitting ratio with waveguide width 8 ${\mu}{\textrm}{m}$, branching angle 0.55$^{\circ}$ and interfering length 470 ${\mu}{\textrm}{m}$ showed 16.18 dB, 21.25 dB for TE and TM input polarization modes, respectively. Polarization cross-talk of -16.28 dB and -21.28 dB for TE and TM modes was achieved. Total insertion losses of 2.24 dB/cm (TE) and 2.41 dB/cm (TM) were also measured. The devices operated nearly wavelength independently over a range or 30 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.146-153
• /
• 1998

The optical near-field patterns, propagation loss and mode sizes of x-cut $Ti:LiNbO_3$ optical waveguide which was fabricated by Ti-diffusion varying with Ti strip thickness in wet oxygen atmosphere were discussed at optical wavelength 1550nm. As Ti thickness increased from $760{\AA}$, the insertion loss of waveguide was decreased. But at Ti thickness $1500{\AA}$, mode sizes are widely broadened. The Ti thickness of below $1100{\AA}$ and above $1500{\AA}$ showed negative effects to propagation loss and fiber coupling. The best Ti thickness for fabricating low propagation loss and good fiber coupling was inferred to be between $1100{\AA}-1500{\AA}$ in our conditions. And for Ti thickness $1150{\AA}$, its propagation loss, horizontal/vertical mode sizes were showed 1.61 dB/cm, $11.9/8.9{\mu}m$ for TM, 0.22 dB/cm, $12.0/9.1{\mu}m$ for TE respectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.264-268
• /
• 1990

A guided-wave electro-optic Mach-Zehnder interferometric modulator was fabricated on X-cut LiNbO3 . The channel waveguides were formed by proton diffusion with self-aligned SiO2-cladding. A mach-Zehnder interferometric modulator with arm lengths of 7mm has been fabricated and tested at 0.6328${\mu}{\textrm}{m}$. Its modulation depth with V$\pi$ of only 3.5V was 85% and the 3dB bandwidth was 1.6KHz. For high speed operation, the electrode dimension should be reduced to have smaller R, L, and C.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.140-140
• /
• 2003

Ti:LiNbO$_3$ 광 도파로를 이용한 광 변조기의 마이크로파 손실을 감소시키고 RF와 광파의 속도정합의 조건하에서 초고속 광변조의 제작을 위해서는 두꺼운 TW(travelling wave) 전극이 필수적이다 또한, 두꺼운 Au 전극이 우수한 RF 특성을 갖기 위해서는 도금된 Au 전극이 고순도의 작은 grain size를 갖는 도금 층을 제조하여야 하며, 도금 후 Au 층의 뒤틀림 현상이 작아야 한다. 따라서, 본 연구에서는 LiNbO$_3$ 기판 위에 30nm Ni-Cr과 50nm의 Au의 기저 막을 올렸으며 감광제를 이용한 photo-lithography 공정으로 CPW(coplanar waveguide) 구조의 패턴을 약 13$\mu\textrm{m}$의 두께로 형성 한 후 non-cyanidic 액을 이용하여 전류밀도 0.02 - 0.06 mA, bubble 및 non-bubble flow를 조건으로 하여 도금된 Au 전극의 특성을 관찰하였다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.80-90
• /
• 1995

In this paper, methods of designing CPW(coplanar waveguide) traveling-wave electrodes are described and their properties are discussed. Especially, the effect of buffer layer thickness to the microwave characteristics of the CPW electrodes are studied in detail. The trade-off relationship between buffer layer thickness and electro-optical properties of the devices are clearly revealde. The microwave characteristics and driving voltage can be further improved by using selected parameters suggested in this paper. To reduce time and effort in designing CPW electrode structure, exact analytical models are proposed.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.199-207
• /
• 2008

Wavelength converting devices with a ridge-type waveguide in periodically poled $MgO:LiNbO_3$ are made and characterized. The experimental results are compared with theoretical analysis on the effects of waveguide dimension and duty ratio of the periodically poled structure. To show the relationship of the conversion efficiency to those factors, a new measurement system is configured. That experimental results show that the center wavelength, normalized conversion efficiency and full width half maximum of the conversion efficiency curve are 1067.45 nm, 90.7%/$Wcm^2$ and 0.17 nm, respectively. Also, the estimated results of the duty period and full width half maximum of the conversion efficiency from theoretical calculations agreed well with experimental results with the errors of 0.016 ${\mu}m$ and 0.01 nm.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.254-258
• /
• 2002

To realize channel cross-connecting in optical communications systems, a high speed optical matrix switch was fabricated using z-cut $LiNbO_3$. For switch fabrication was design bending structure and coupling length and four $2{\times}2$ directional couplers were integrated on one substrate far construction of a $4{\times}4$ switch. Single-mode optical waveguides were formed by Ti-diffusion at a wet $O_2$ atmosphere. Ti-diffusion profile, refractive index variation and waveguide morphology were analyzed by Prism coupler and optical microscopy, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.128-134
• /
• 2012

The performance evaluation and fabrication of integrated-optic electric-field sensor utilizing $Ti:LiNbO_3$ asymmetric Mach-Zehnder intensity modulator with a push-pull lumped electrode and a plate-type probe antenna to measure an electric field strength is described. The modulator has a small device size of $46{\times}7{\times}1\;mm$ and operates at a wavelength $1.3{\mu}m$. The devices are simulated based on the BPM software and fabricated utilizing Ti-diffused $LiNbO_3$ channel optical waveguides. The minimum detectable electric field is 1.02 V/m and 6.91 V/m, corresponding to a dynamic range of ~35 dB and ~10 dB at the frequencies of 500 KHz and 5 MHz, respectively.