• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1162-1166
• /
• 2001

NiZn-ferrite was synthesized from waste catalysts, which were produced from styrene monomer process and buried underground as an industrial wastes, and its magnetic properties were investigated. Nickel oxide and zinc oxide powders were mixed with finely ground waste catalysts, and spinel type ferrite was obtained by calcination at 900$\^{C}$ and sintering at 1230$\^{C}$ for 5 hours. The intial permeability was measured and reflection loss was calculated from S-parameters for the composition of Ni$\_$x/Zn$\_$1-x/Fe$_2$O$_4$(x=0.36, 0.50, 0.66). NiZn-ferrite synthesized from waste iron oxide catalyst showed a feasibility for the use as electromagnetic wave absorber in X-band.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.239-242
• /
• 2006

LCD-BLU (Liquid Crystal Display - Back Light Unit) is one of kernel parts of LCD unit and it consists of several optical sheets(such as prism, diffuser and protector sheets), LGP (Light Guiding Plate), light source (CCFL or LED) and mold frame. The LGP of LCD-BLU is usually manufactured by forming numerous dots with $50{\sim}200$ um in diameter on it by etching process. But the surface of the etched dots of LGP is very rough due to the characteristics of the etching process during the mold fabrication, so that its light loss is high along with the dispersion of light into the surface. Accordingly, there is a limit in raising the luminance of LCD-BLU. In order to overcome the limit of current etched dot patterned LGP, optical pattern design with 50um micro-lens was applied in the present study. The micro-lens pattern fabricated by modified LiGA with thermal reflow process was applied to the optical design of LGP. The attention was paid to the effects of different aspect ratio (i.e. $0.2{\sim}0.5$) of optical pattern conditions to the brightness distribution of BLU with micro-lens patterned LGP. Finally, high aspect ratio micro-lens patterned LGP showed superior results to the one made by low aspect ratio in average luminance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.263-266
• /
• 2001

In this paper, we investigated dielectric properies for BST thin films that was deposited on MgO/Si substrates using RF magnetron sputtering. In here, MgO film was used to perform that a diffusion b arrier between the BST film and Si substrate and a buffer layer to assist the BST film growth. A d eposition condition for MgO films was RF Power of 50W, substrate temperature of room temperature and the working gas ratio of Ar:O$_2$ were varied from 90:10 to 60:47. Finally we manufactured the cap acitor of Al/BST/MgO/Si/Al structure to know electrical properties of this capacitor through I-V, C-V measurement. In the results, C-V aha racteristic curves was shown a ferroelectric property so we measured P-E. A remanent poliazation and coerceive electric field was present 2$\mu$C/cm$^2$ and -27kV/cm respectively at Ar:O$_2$=90:10. And a va clue of dielectric constant was 86 at Ar:02=90:10.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.17 no.2
• /
• pp.173-180
• /
• 2008

The influence of temperature and relative humidity in infection and cross-infection of Nosema bombycis and N. mylitta respectively in mulberry silkworm, Bombyx mori L. on larval mortality, multiplication of pathogens, larval weight and growth rate in three different seasons were studied. Seasons were selected in such condition, when very less fluctuations between minimum and maximum temperature and minimum and maximum relative humidity ($25{\sim}28^{\circ}C$ and $65{\sim}72%$ R.H) was observed i.e., season-1. Fluctuations between minimum and maximum temperature were less ($28.05{\sim}34.50^{\circ}C$) but R.H % was more ($55{\sim}81%$) in season-2. Fluctuations between minimum and maximum temperature and R.H % were more ($20.00{\sim}40.5^{\circ}C$ and $64.00{\sim}90.00%$) in season-3. Growth rate of microsporidian-infected silkworm is directly related to the prevailing temperature and relative humidity in silkworm. Silkworm can tolerate slight variation of temperature but slight variation of relative humidity disfavours the development of silkworm and favours the multiplication of pathogens.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.4
• /
• pp.300-307
• /
• 2018

PURPOSE. To investigate the fatigue and fracture resistance of computer-aided design and computer-aided manufacturing (CAD/CAM) ceramic molar crowns on dental implants and human teeth. MATERIALS AND METHODS. Molar crowns (n=48; n=8/group) were fabricated of a lithium-disilicate-strengthened lithium aluminosilicate glass ceramic (N). Surfaces were polished (P) or glazed (G). Crowns were tested on human teeth (T) and implant-abutment analogues (I) simulating a chairside (C, crown bonded to abutment) or labside (L, screw channel) procedure for implant groups. Polished/glazed lithium disilicate (E) crowns (n=16) served as reference. Combined thermal cycling and mechanical loading (TC: $3000{\times}5^{\circ}C/3000{\times}55^{\circ}C$; ML: $1.2{\time}10^6$ cycles, 50 N) with antagonistic human molars (groups T) and steatite spheres (groups I) was performed under a chewing simulator. TCML crowns were then analyzed for failures (optical microscopy, SEM) and fracture force was determined. Data were statistically analyzed (Kolmogorow-Smirnov, one-way-ANOVA, post-hoc Bonferroni, ${\alpha}=.05$). RESULTS. All crowns survived TCML and showed small traces of wear. In human teeth groups, fracture forces of N crowns varied between $1214{\pm}293N$ (NPT) and $1324{\pm}498N$ (NGT), differing significantly ($P{\leq}.003$) from the polished reference EPT ($2044{\pm}302N$). Fracture forces in implant groups varied between $934{\pm}154N$ (NGI_L) and $1782{\pm}153N$ (NPI_C), providing higher values for the respective chairside crowns. Differences between polishing and glazing were not significant ($P{\geq}.066$) between crowns of identical materials and abutment support. CONCLUSION. Fracture resistance was influenced by the ceramic material, and partly by the tooth or implant situation and the clinical procedure (chairside/labside). Type of surface finish (polishing/glazing) had no significant influence. Clinical survival of the new glass ceramic may be comparable to lithium disilicate.

• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.9
• /
• pp.1326-1331
• /
• 2003

The aim of the study was to assess the efficacy of Toyocerin, a probiotic containing Bacillus toyoi spores, on the health status and productivity of pigs, during nursery, growing and finishing phases. On a commercial farrow-to-finish farm in Greece, 3 experimental groups were formed, each of 72 weaned piglets. The pigs of the first group (T1 group; negative controls) received normal feed with no antimicrobials or probiotics, the pigs of the second group (T2 group) received the same type of feed but supplemented with 1.0${\times}$10$^9$, 0.5${\times}$10$^9$ and 0.2${\times}$10$^9$ spores per kg of feed at weaning, growing and finishing stage, respectively, and the pigs of the third group (T3 group) were fed with Toyocerin at the dose of 1.0${\times}$10$^9$ spores per kg of feed during the entire fattening period (weaning, growing and finishing stages). The results have shown that, compared to the controls, Toyocerin treated pigs had reduced incidence of postweaning diarrhoea (p<0.05). Enterotoxigenic strains of Escherichia coli were detected in faecal samples of 0% to 25% of pigs of the treated groups, but in 33.5% to 50% of pigs of the non-treated group (p<0.05). Over the negative controls, a significant improvement of weight gain (4.5% and 8.3% for T2 and T3 groups, respectively), and of feed conversion ratio (6.6% and 13.0% for T2 and T3 groups, respectively) was observed. The 76.5% of the carcasses of the T3 group was classified in the top three categories of the EUROP scale (S, E and U), whilst the respective figures were 47.8% for T2 group and only 10.5% for T1 group (p<0.05).

• The Korean Journal of Physiology and Pharmacology
• /
• v.23 no.4
• /
• pp.231-236
• /
• 2019

In drug discovery or preclinical stages of development, potency parameters such as $IC_{50}$, $K_i$, or $K_d$ in vitro have been routinely used to predict the parameters of efficacious exposure (AUC, $C_{min}$, etc.) in humans. However, to our knowledge, the fundamental assumption that the potency in vitro is correlated with the efficacious concentration in vivo in humans has not been investigated extensively. Thus, the present review examined this assumption by comparing a wide range of published pharmacokinetic (PK) and potency data. If the drug potency in vitro and its in vivo effectiveness in humans are well correlated, the steady-state average unbound concentrations in humans [$C_{u_-ss.avg}=f_u{\cdot}F{\cdot}Dose/(CL{\cdot}{\tau})=f_u{\cdot}AUCss/{\tau}$] after treatment with approved dosage regimens should be higher than, or at least comparable to, the potency parameters assessed in vitro. We reviewed the ratios of $C_{u_-ss.avg}$/potency in vitro for a total of 54 drug entities (13 major therapeutic classes) using the dosage, PK, and in vitro potency reported in the published literature. For 54 drugs, the $C_{u_-ss.avg}$/in vitro potency ratios were < 1 for 38 (69%) and < 0.1 for 22 (34%) drugs. When the ratios were plotted against $f_u$ (unbound fraction), "ratio < 1" was predominant for drugs with high protein binding (90% of drugs with $f_u{\leq}5%$; i.e., 28 of 31 drugs). Thus, predicting the in vivo efficacious unbound concentrations in humans using only in vitro potency data and $f_u$ should be avoided, especially for molecules with high protein binding.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.391-396
• /
• 2010

In this research the characteristics of ammonia removal from malodorous waste-air were investigated under various operating condition of biofiilter packed with equal volume of rubber media and compost for the efficient removal of ammonia, representative source of malodor frequently generated at compost manufacturing factory and publicly owned facilities. Then the optimum conditions were constructed to treat waste-air containing ammonia with biofilter. Biofilter was run for 30 days(experimental frequency of 2 times/day makes 60 experimental times.) with the ammonia loading from $2.18g-N/m^3/h$ to $70g-N/m^3/h$ at $30^{\circ}C$. The ammonia removal efficiency reached almost 100% for I through IV stage of run to degrade up to the ammonia loading of $17g-N/m^3/h$. However the removal efficiency dropped to 80% when ammonia loading increased to $35g-N/m^3/h$, which makes the elimination capacity of ammonia $28g-N/m^3/h$ for V stage of run. However, the removal efficiency remained 80% and the maximum elimination capacity reached $55g-N/m^3/h$ when ammonia loading was doubled $70g-N/m^3/h$ for VI stage of run. Thus the maximum elimination capacity exceeded $1,200g-N/m^3/day$(i.e., $50g-N/m^3/h$) of the experiment of biofilter packed with rock wool inoculated with night soil sludge by Kim et al.. However, the critical loading did not exceed $810g-N/m^3/day$ (i.e., $33.75g-N/m^3/h$) of the biofilter experiment by Kim et al.. The reason to exceed the maximum elimination capacity of Kim et al. may be attributed to that the rubber media used as biofilter packing material provide the better environment for the fixation of nitrifying and denitrification bacteria to its surface coated with coconut based-activated carbon powder and well-developed inner-pores, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.11
• /
• pp.961-966
• /
• 1994

Oligomerization of phenylacetylene is catalyzed by $Rh(ClO_4)(CO)(PPh_3)_2$ (Rh-1), $[Rh(CO)(PPh_3)_3]ClO_4$ (Rh-2), $[Rh(COD)L_2]ClO_4 (L_2=(PPh_3)_2$, Rh-3; $(PPh_3)(PhCN)$, Rh-4; $(PhCN)_2$, Rh-5), $[Rh(C_3H_5)(Cl)(CO)(SbPh_3)_2]ClO_4$ (Rh-6), $[Ir(COD)L_2]ClO_4 (L_2=(PPh_3)_2$, $Ir-1; (PPh_3)(PhCN)$, $Ir-2; (PhCN)_2$, Ir-3; (AsPh_3)(PhCN)$, $Ir-4; Ph_2PCH_2CH_2PPh_2$, Ir-5; COD, Ir-6 and 2,2'-dipyridyl, Ir-7), $Ir(ClO_4)(CO)(PPh_3)_2$, $Ir-8, [Ir(PhCN)(CO)(PPh_3)_2]ClO_4$, Ir-9 to produce dimerization products, 1,3-diphenylbut-1-yn-3-ene, 1, (E)-1,4-diphenylbut-1-yn-3-ene, 2 and (Z)-1,4-diphenylbut-1-yn-3-ene, 3, and cyclotrimerization products, 1,3,5-triphenylbenzene, 4 and 1,2,4-triphenylbenzene, 5. Product distribution of the oligomers varies depending on various factors such as the nature of catalysts, reaction temperature, counter anions and excess ligand present in the reaction mixtures. Increasing reaction temperature in general increases the yield of the cyclotrimerization products. Exclusive production of dimer 1 and trimer 4 can be obtained with Ir-1 at 0 $^{\circ}$C and with Ir-2 in the presence of excess PhCN (or $CH_3CN$) at 50 $^{\circ}$C, respectively. Dimer 2 (up to 81%) and trimer 5 (up to 98%) are selectively produced with Rh-1 at 50 and 100 $^{\circ}$C respectively. Production of 3 is selectively increased up to 85% by using $PF_6$- salt of $[Ir(COD)(PPh_3)_2]$+ at 25 $^{\circ}$C. Addition of $CH_3I$ to Rh-1 produces $CH_3PPh_3^+I-$ and increases the rate of oligomerization(disappearance of phenylacetylene). Among the metal compounds investigated in this study, Ir-1 catalyzes most rapidly the oligomerization where the catalytically active species seems to contain lr(PPh3)2 moiety. The stoichiometric reaction of phenylacetylene wth Ir-9 at 25 $^{\circ}$C quantitatively produces hydridophenyl-ethynyl iridium(III) complex, $[lr(H)(C{\equiv}CPh)(PhCN)(CO)(PPh_3)_2]ClO_4$ (Ir-11), which seems to be an intermediate for the oligomerization.

• Journal of Animal Science and Technology
• /
• v.44 no.6
• /
• pp.719-726
• /
• 2002

Nutritional adequacy of growing Thoroughbred horses raised in an alternate feeding system - grazing during late spring through late fall and stable feeding for the rest of seasons - was assessed by determining vitamin E and trace mineral levels in the serum and blood chemistry related to nutrition and health. During the stable feeding in winter and early spring, 50 growing female horses were fed concentrates (1.4% of their body weight), grass hay (0.62%) and alfalfa hay (0.37%). For the grazing period, the same horses were fed supplementary concentrates (1.1%) during late spring through early summer, and concentrates (1.1%) and alfalfa hay (0.5%) during late summer through late fall. Blood samples were collected before grazing in early spring, and during grazing in early summer through late fall. Serum vitamin E, BUN, GTP, total bilirubin and direct bilirubin levels were increased (P<0.01) by grazing compared to those measured before the initiation of grazing. Horses had lower (P<0.01) serum Fe contents in early summer than in late fall or in time of stable feeding. Stable feeding increased (P<0.01) serum Cu content compared to grazing in both early summer and late fall. In late fall, serum Zn level increased (P<0.01) compared to that found in the other seasons. Blood glucose and creatinine levels decreased (P<0.01) after grazing. Results indicate that supplementations of some minerals and vitamin E are not always necessary in diets for growing horses and should be done after careful evaluation of diets with regard to concentrations and biological availability of minerals.