• 비파괴검사학회지
• /
• 제29권5호
• /
• pp.450-457
• /
• 2009

열차폐 코팅 시편에 대하여 열충격을 주기적으로 가한 후 발생하는 결함을 관찰하였다. 실험에 사용 된 열차폐 코팅 시편은 인코넬-738로 제작된 모재 위에 CoNiCrAlY 본드 코팅층과 $ZrO_2-8wt%Y_2O_3$ 세라믹탑 코팅층이 플라즈마 용사 방법으로 올려진 형태로 되어있다. 열충격 시험은 $1000^{\circ}C$의 고온으로 가열했다가 상온으로 급격하게 냉각시키는 가혹한 조건으로 실행되었고, 사이클 수가 증가함에 따라 열충격의 피로도 또한 증가하였다. 시험후 시편 내부의 미세 조직 변화와 결함을 전자현미경으로 관찰하고, 시편의 기계적인 특성을 측정하여 그 변화 양상을 살펴보았다. 열충격 주기실험후 본드 코팅층과 세라믹 탑 코팅층 사이에 발생하는 TGO 산화물층에 대한 변화 양상과 이에 대한 와전류 신호를 측정하여 TGO층 성장 거동의 비파괴적인 평가를 위한 실험을 진행하였다. 본 연구를 통하여 마이크로 단위의 TGO층에 대한 와전류검사의 적용 가능성을 확인하고 열차폐 코팅의 수명을 예측할 수 있는 가능성을 제시하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1349-1352
• /
• 2005

This paper is to investigate a defect for thermal barrier coating layers by acoustic emission method in 4-point bending test. The two-layer thermal barrier coating is composed of $150\mu{m}\;CoNiCrAlY\;bond\;coating\;by\;vacuum\;plasma\;spray(VPS)\;process\;and\;250\mu{m}\;ZrO_2-8wt%Y_2O_3$ ceramic coating layer by air plasma spray(APS) process on Inconel-718. The specimen prepared by cyclic thermal test(500, 1000, 2000cycle) at $1050^{\circ}C$ The AE monitoring system is composed of PICO type sensor, a wide band pre-amplifier(40dB), PC and AE DSP(16/32 PAC) board. The AE event, amplitude, Cumulative energy and count of coating specimens is evaluated according to cyclic thermal test.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.339-339
• /
• 2002

In the RABiTS approach to coated conductor development, successful (both economic and technological) depends on the refinement and optimization of each of three important components: the metal tape substrate, the buffer layer(s), and the HTS layer. Here we will report on the ORNL approach and progress in each of these areas. - Most applications will require metal tapes with low magnetic hysteresis, mechanical strength, and excellent crystalline texture. Some of these requirements are competing. We report on progress in obtaining a good combination of these characteristics on metal alloys of Ni-Cr and Ni-W. - The deposition of appropriate buffer layers is a crucial step. Recently, base research has shown that the presence of a stable sulfur superstructure present on the metal surface is needed for the nucleation and epitaxial growth of vapor-deposited seed buffer layers such as YSZ, CeO$_2$ and SrTiO$_3$. We report on the details and control of this superstructure for nickel tapes, as well as recent results for Cu and Ni-13%Cr. - Processes for deposition of the HTS coating must economically provide large values of the figure-of-merit for conductors, current x length. At ORNL, we have devoted efforts to a precursor/post-annealing approach to YBCO coatings, for which the deposition and reaction steps are separate. We describe motivation for and progress toward developing this approach. - Finally, we address some issues for the implementation of coated conductors in real applications, including the need for texture control and electrical stabilization of the HTS coating.

• 한국표면공학회지
• /
• 제32권2호
• /
• pp.144-156
• /
• 1999

Thermal Barrier Coating with Functional Gradient Materials (FGM-TBC) can play an important role to protect the parts from harmful environments in high temperatures such as oxidation, corrosion, and wear and to improve the efficiency of aircraft engine by lowering the surface temperature on turbine blade. FGM-TBC can increase the life spans of product and improve the operating properties. Therfore, in this study the evaluations of mechanical and thermal properties of FGM-TBC such as fatigue, oxidation and wear-resistance at high temperatures have been conducted. The samples of both the TBC with 2, 3, 5 layers (YSZ/NiCrAlY) to be produced by Air Plasma Spray method (APS) and the bulk TBC with 6 layers to be produced by Plasma Assisted Sintering method (PAS) were used. Furthermore, residual stress, bond strength, and thermal conductivity were evaluated. The average thickness of the APS was 500$\mu\textrm{m}$ to 600$\mu\textrm{m}$ and the average thickness of the PAS was 3mm. The hardness number of the top layer of APS was 750 Hv to 810Hv and that of PAS was 950 Hv to 1440Hv. The $ZrO_2$ coating layer of APS was composed of tetragonal structure after spraying as the result of XRD analysis. As shown in the results of the high temperature wear test, the 3 layer coating of APS had the best wear resistance at $800^{\circ}C$ and the 5 layer coating of APS had the best wear resistance at $600^{\circ}C$. But, these coatings had the tendency of the low-temperature softening at $300^{\circ}C$. The main mechanism of wear was the adhesive wear and the friction coefficient of coatings was increased as increasing the test temperatures. A s results of thermal conductivity test, the ${\Delta}T$ of the APS coating was increased as number of layer and the range of thermal conductivity of the PAS was $800^{\circ}C$ to $1000^{\circ}C$.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.66-74
• /
• 2004

The sliding wear behavior of $ZrO_2-22wt\%MgO\;(MZ)\;and\;ZrO_2-8wt\%Y_2O_3\;(YZ)$ deposited on a casting aluminum alloy with bond layer (NiCrCoAlY) by plasma spray against an SiC ball was investigated under dry test conditions at room temperature. At all load conditions, the wear mechanisms of the MZ and the YZ coatings were almost the same. The wear mechanisms involved the forming of a smooth film by material transferred on the sliding surface and pullout. The wear rate of the MZ coating was less than that of the YZ coating. With an increase normal load the wear rate of the studied coatings increased. The SEM was used to examine the sliding surfaces and elucidate likely wear mechanisms. The EDX analysis of the worn surface indicated that material transfer was occurred from the SiC ball to the disk. It was suggested that the material transfer played an important role in the wear performance.

• 방사성폐기물학회지
• /
• 제8권1호
• /
• pp.33-39
• /
• 2010

산화물 사용 후 핵연료를 처리하는 전해환원공정에서는 LiCl 용융염계에서 산소가 생성되는 반응을 수반하게 되며, 생성된 산소로 인해 반응기의 구조재료를 상당히 부식시킬 수 있는, 화학적으로 심각한 반응환경을 조성한다. 따라서, 고온 용융염을 다루는 전해환원 공정장치를 위해서는 최적의 재료를 선택하는 것이 필수적이다. 본 연구에 서는 리튬용융염, $675^{\circ}C$, 216시간동안 산화분위기에서 코팅이 안 된 초합금과 코팅된 초합금 시편의 고온 부식연구를 수행하였다. IN713LC 초합금 시편에 aluminized NiCrAlY bond 코팅 후 $Y_2O_3$ top 코팅을 하였다. 코팅이 안 된 초합금은 부식층의 빠른 성장응력과 열적응력에 의한 부식층의 박리로 명확한 무게손실을 보인다. 탑 코팅의 화학적 및 열적 안정성으로 인해 고온 리튬용융염을 다루는 구조재료의 부식 저항성이 증가함을 확인할 수 있었다.

• 한국표면공학회지
• /
• 제30권4호
• /
• pp.272-280
• /
• 1997

The Thermal Barrier Coation(TBC) to improve the that barrier and wear resistant propenrty in high temperature ofthe aircraftength between the accumlation of the aircraft engine and the automobile engine has usually the two layer structure. One is a creamic top layer for heat insulation and the other is a metal bond layer to facilitate the bond strength between the top ceramic layer and the substrate. But, the coated layers should be peeled off because of the accumulation of the thermal stress by the differance of the thermal expantion coefficient between metal and ceramics in a hrat cyclic environment. In this study, the intermediate layer by plasm spray process was introduced to reduce the thermal stress. The powders of plasm spray coating were the Yttria Stabilized Zirconia (YSZ), the Magnesia Stabillized Zirconia(MSZ) and NiCrAlY. the intermediate layer was sprayed with the powders of the bond cast for the purpose of test were executed. The high temperature wear resistance tends to decreasnceee wear and thermal shock test were exeucuted. The high temperature were resistance of the YSZ TBC is better that of the MSZ TBC. The wearrsistance tends to decrease accoring to incresing the temperature between $400^{\circ}C$to $600^{\circ}C$. The thermal shock life of the 3 layer TBC with YSZ top casting was the most outstanding thermal shock rsisstasnce. This means that the intermediate layer should play an importnat roll to alleviate the diffrerence of the thermal expansion coef frcients between metallic layer and cermics layer.

• 청정기술
• /
• 제25권3호
• /
• pp.256-262
• /
• 2019

Hydroxylammonium nitrate (HAN) 기반 액상 추진제는 발암물질이 아니며 연소가스 또한 독성이 거의 없어서 환경 친화적인 추진제로 주목을 받고 있다. 추력기에서 HAN 기반 액체추진제를 분해하는데 사용되는 촉매는 저온 활성 및 고내열성을 동시에 보유하고 있어야 한다. 본 연구의 목적은 metal foam 표면에 alumina slurry를 wash coating 방법으로 담지한 후, 루테늄(ruthenium) 전구체를 그 위에 담지하여 Ru/alumina/metal foam 촉매를 제조하고, 이 촉매의 HAN 수용액 분해 활성을 평가하는 것이다. Wash coating 방법으로 metal foam 지지체에 알루미나를 담지시키는 과정에서 wash coating 반복 횟수가 alumina/metal foam의 물리적 특성에 미치는 영향을 분석하였다. 알루미나 wash coating 횟수가 증가할수록 약 7 nm의 직경을 갖는 메조기공이 지속적으로 발달하여 표면적과 기공 부피가 증가하는데, metal foam에 알루미나를 코팅하는 과정을 12 회 반복하는 것이 최적이라고 판단하였다. 이 지지체에 Ru을 담지한 Ru/alumina/metal foam 촉매의 표면에도 메조기공이 잘 발달하였다. 활성금속과 알루미나를 담지하지 않은 metal foam 자체만으로도 HAN 수용액의 분해반응을 촉진할 수 있음을 알 수 있었다. Ru/alumina/metal foam-550촉매의 경우는 열분해 반응에 비해서 분해개시온도를 큰 폭으로 낮추었고, ${\Delta}P$를 크게 증가시킬 수 있어서, HAN 수용액 분해 반응에서 우수한 활성을 보였다. 그러나 이 촉매를 $1,200^{\circ}C$에서 소성하면 반응 활성이 저하되는데 이는 촉매의 표면적과 기공 부피가 급격하게 감소하고 Ru이 소결되기 때문이다. 추가적인 연구를 통해서 Ru/alumina/metal foam의 내열성을 개선할 필요성이 있다.