• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.184-192
• /
• 1999

Various compositions of$ Cr_2$$O_3$/Mo composite powders were fabricated using spray-drying method and plasma-spray coatings of these powders were prepared to understand their tribological properties. Experiments were conducted using a reciprocal type tribo-tester at room temperature under dry sliding condition. The worn surface of coated specimens were observed using SEM (Scanning Electron Microscopy) and chemical compositions were analyzed using XRD (X-ray Diffractometry) and XPS (X-ray Photoelectron Spectroscopy). The results showed that friction coefficient of the Mo added specimens were lower than that of $Cr_2$$O_3$specimen. However $Cr_2$$O_3$specimen showed the lowest wear loss. Wear protecting layer were observed at the worn surface of coated specimens with Mo addition. From the XPS analysis, the mixed phases of $Cr_2$$O_3$ $CrO_3$and $MoO_3$were founded in the wear protecting layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.12
• /
• pp.762-767
• /
• 2017

Mullite ($3Al_2O_3{\cdot}2SiO_2$) has emerged as a promising candidate for high-temperature structural materials due to its erosion resistance, chemical and thermal stabilities, relatively low thermal expansion coefficient, excellent thermal shock and creep resistances, and low dielectric constant. However, since the pure mullite sintering temperature is as high as $1,600{\sim}1,700^{\circ}C$, there is an increasing need for a sintering additive capable of improving the strength characteristics while lowering the sintering temperature. Herein we have tried to obtain the optimal sintering additive composition by adding MgO, $Cr_2O_3$, and $Y_2O_3$ to mullite, followed by sintering at $1,325{\sim}1,550^{\circ}C$ for 2 h. With additives of 2 wt% of MgO, 2 wt% of $Cr_2O_3$, 4 wt% of $Y_2O_3$, A density of $3.23g/cm^3$ was obtained for the sintered body at $1,350^{\circ}C$ upon using 2 wt% MgO, 2 wt% $Cr_2O_3$, and 4 wt% $Y_2O_3$ as additives. The three-point flexural strength of that was 275 MPa and the coefficient of thermal expansion (CTE) was $4.15ppm/^{\circ}C$.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.4
• /
• pp.125-130
• /
• 2011

$Cr_2AlC$ compounds were synthesized by hot pressing, and oxidized between 900 and $1200^{\circ}C$ in air for up to 50 hours. They oxidized to a thin $Al_2O_3$ layer containing a small amount of $Cr_2O_3$with the liberation of carbon as CO or $CO_2$ gases. The consumption of Al to form the $Al_2O_3$ layer led to the depletion of Al and enrichment of Cr just below the $Al_2O_3$ layer, resulting in the formation of an underlying $Cr_7C_3$ layer. As the oxidation temperature and time increased, the $Cr_7C_3$ oxide layer and the underlying $Cr_7C_3$ layer thickened. The oxidation resistance of $Cr_2AlC$ was generally good due to the formation of the $Al_2O_3$ barrier layer.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.689-695
• /
• 2012

We have examined the co-doping effects of 1/2 mol% NiO and 1/4 mol% $Cr_2O_3$ (Ni:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Ni,Cr-doped ZBS, ZBS(NiCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were detected for all of compositions. For the sample with Sb/Bi = 1.0, the Pyrochlore was decomposed and promoted densification at lower temperature by Ni rather than by Cr. A homogeneous microstructure was obtained for all of the samples affected by ${\alpha}$-spinel. The varistor characteristics were not dramatically improved (non-linear coefficient, ${\alpha}$ = 5~24), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.17 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to have been divided into two types, i.e., one is tentatively assigned to ZnO/$Bi_2O_3$ (Ni,Cr)/ZnO (0.98 eV) and the other is assigned to a ZnO/ZnO (~1.5 eV) homojunction.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.192-193
• /
• 2009

CrN 코팅막은 고온에서 치밀한 Cr2O3 확산방지막을 형성함으로 $800^{\circ}C$까지 기계적성질을 유지할 수 있다. 본 실험에서는 Ar, N2, 그리고 $O_2$ 가스 분위기에서 AIP(Arc Ion Plating) 기법에 의해 다양한 조성의 Cr-O-N 박막을 Si(200)과 AISI 304 기판 위에 증착되었다. Cr-O-N 코팅막은 47.4at% 미만의 산소함량을 포함 할 때까지 B1구조를 유지하였고 코팅막 내 산소함량 24.6at%에서는 강한 XRD peak intensification을 나타내었다. 47.4at%에서는 결정상을 전혀 찾아볼 수 없는 전이구조를 나타내었고, 그 이상의 산소함량에서는 Cr22O3 결정상을 나타내었다. Cr-O(17at%)-N 조성의 코팅막에서는 (200)배향의 Grain 크기 증가 및 압축잔류응력이 증가하였으나, 그 이상의 산소함량에서는 점차 감소하였다. Cr-O(24.6at%)-N 조성의 코팅막이 가장 높은 경도를 나타내었고, 산소함량이 증가할수록 점차 향상된 마찰특성을 보였다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.1
• /
• pp.58-65
• /
• 2005

The $LaCrO_3$-dispersed Cr alloys for metallic interconnect of solid oxide fuel cell were prepared as a function of $LaCrO_3$ content in the range of 5 to 25 vol.% and were sintered at 1500$^{\circ}C$ under an Ar atmosphere with 5 vol.% $H_2$. The sintering and oxidation behaviors of these alloys were examined. The alloys indicated a good sinterability above 95% relative density at a given sintering condition, and their sintering densities is independent on $LaCrO_3$ content. The $LaCrO_3$ particles of the sintered alloys were concentrated on interfaces of Cr particles, and the size of the Cr particles increased with decreasing $LaCrO_3$ content, which is caused by inhibited grain growth of Cr particle by $LaCrO_3$ particle. The oxidation test showed all $LaCrO_3$-dispersed Cr alloys have good oxidation resistance as compared with pure Cr, which is attributed to presence of $LaCrO_3$ at the interface at which the oxidation reaction occurs rapidly. The Cr alloys with about 15 vol.% $LaCrO_3$ are very resistant to oxidation.

• Korean Journal of Metals and Materials
• /
• v.46 no.9
• /
• pp.577-584
• /
• 2008

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Inconel 713LC, Inconel MA 754, Nimonic 80A and Nimonic 90 in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere was investigated at $650^{\circ}C$ for 72~216 hrs. Inconel 713LC alloy showed the highest corrosion resistance among the examined alloys. Corrosion products of Inconel 713LC were $Cr_2O_3$, $NiCr_2O_4$ and NiO, and those of Inconel MA 754 were $Cr_2O_3$ and $Li_2Ni_8O_{10}$ while $Cr_2O_3$, $LiFeO_2$, $(Cr,Ti)_2O_3$ and $Li_2Ni_8O_{10}$ were produced from Nimonic 80A. Also, corrosion products of Nimonic 90 were found to be $Cr_2O_3$, $(Cr,Ti)_2O_3$, $LiAlO_2$ and $CoCr_2O_4$. Inconel 713LC showed local corrosion behavior and Inconel MA 754, Nimonic 80A, Nimonic 90 showed uniform corrosion behavior.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.14-14
• /
• 2009

In this study, we investigated the effects of Cr dopant on the bulk trap level and grain boundary characteristics of $Bi_2O_3$-based ZnO (ZB) using dielectric functions such as $Z^*$, $Y^*$, $M^*$, ${\varepsilon}^*$, and $tan{\delta}$. More than two bulk traps of $Zn_i$ and $V_o$ probably in different ionization states could be identified in ZBCr($ZnO-Bi_2O_3-Cr_2O_3$). The grain boundaries of ZBCr could be electrochemically divided into two types: sensitive to ambient oxygen and thus electrically active one and oxygen-insensitive and thus electrically inactive one.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.9
• /
• pp.1395-1402
• /
• 2005

The reaction of cis-[Cr([14]-decane)$(OH)_2]^+$ ([14]-decane = rac-5,5,7,12,12,14-hexamethyl-1,4,8,11-teraazacyclotetradecane) with auxiliary ligands {$L_a$ = acetylacetonate (acac), oxalate (ox) or malonate (mal)} leads to a new cis-[Cr([14]-decane)(acac)]$(ClO_4)_2{\cdot}(1/2)H_2O\;(1),\;cis-[Cr([14]-decane)(ox)]ClO_4{\cdot}(1/2)H_2O\;(2)\;or\;cis-[Cr([14]-decane)(mal)]ClO_4{\cdot}(1/4)H_2O\;(3)$. These complexes have been characterized by a combination of elemental analysis, conductivity, IR and Vis spectroscopy, mass spectrometry, and X-ray crystallography. Analysis of the crystal structure of cis-[Cr([14]-decane)(acac)]$(ClO_4)_2{\cdot}(1/2)H_2O$ reveals that central chromium(III) has a distorted octahedral coordination environment and two acetylacetonate-oxygen atoms are bonded to the chromium(III) ion in the cis positions. The angle $N_{axial}-Cr-N_{axial}$ deviates by $11^{\circ}$ from the ideal value of $180^{\circ}$ for a perfect octahedron. The bond angle O-Cr-O between the chromium(III) ion and the two acetylacetonate-oxygen atoms is close to $90^{\circ}$. The bond lengths of Cr-O between the chromium and the acetylacetonate-oxygen atoms are 1.950(3) and 1.954(2) $\AA$. They are shorter than those between chromium and nitrogen atoms of the macrocycle. The IR spectra of 1, 2 and 3 display bands at 1560 {ν (C=O)}, 1710 {${\nu}_{as}$(OCO)} and 1660 $cm^{-1}$ {${\nu}_{as}$(OCO)} attributed to the acac, ox and mal auxiliary ligands stretching vibrations, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.972-975
• /
• 2001

The effect of Cr$_2$O$_3$(0 to 0.5 wt%) doping on the microstructure and electrical properties of ternary Pb(Zr,Ti)O$_3$-Pb(Ni,Nb)O$_3$piezoelectric ceramic has been investigated. Abnormal grain growth (grain size 3.3 to 11.2 $\mu$m) and densification are found. Minor additives of $\leq$0.1 wt% improve the mechanical coupling factor, but with more additives of $\geq$0.2 wt% electrical properties deteriorate. Thus, these phenomna can be ascribed mainly to anomalous developed microstructure. The large grains were composed of a core region that is free of Cr and a surrounding shell region rich in Cr. The interfaces between the core and the shell were composed of misfit dislocations. The mechanical properties of the specimens were strongly influenced by this microstructural change. The microstrutural and compositonal evolution of the specimens containing different amounts of Cr$_2$O$_3$were monitored. Electrical properties were measured and related to the variations in the microstructure.