• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.4672-4678
• /
• 2013

알루미늄 금속이 용해될 시 대기와 접촉한 용탕 표면에서 생성되는 알루미늄 드로스는 알루미늄 생산 공정에서 발생되는 필수적인 부산물이다. 그러나 알루미늄 드로스의 대부분은 매립에 의한 처리가 이루어지고 있어 환경오염의 원인이 되고 있다. 본 연구에서는 알루미늄 드로스를 재자원화 하여 SCR(Selective Catalytic Reduction) 촉매의 담체에 일부 대체하는 연구를 진행하였다. 재활용 된 알루미늄 드로스를 촉매 원료 $WO_3$, $V_2O_5$, $TiO_2$와 혼합하여 $V_2O_5-WO_3/TiO_2-Al_2O_3$ SCR촉매를 제조하였다. 제조 된 $V_2O_5-WO_3/TiO_2-Al_2O_3$ SCR촉매는 XRD, XRF, BET 분석을 통해 특성평가를 진행 하였으며, 내구성 평가를 통해 $Al_2O_3$ 함량이 증가할수록 V$V_2O_5-WO_3/TiO_2-Al_2O_3$ SCR촉매의 강도가 증가하는 것을 확인 할 수 있었다. MR(Micro-Reactor)을 이용한 촉매 활성평가를 진행하여 촉매의 실사용 온도 $350^{\circ}C{\sim}400^{\circ}C$에서 90%이상의 촉매효율을 나타내었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.114-115
• /
• 2013

$Ti_3AlC_2$ was corroded between 800 and $1100^{\circ}C$ in an Ar-0.2% $SO_2$ gas atmosphere according to the equation: $Ti_3AlC_2+O_2{\rightarrow}rutile-TiO_2+{\alpha}-Al_2O_3$ + (CO or $CO_2$). The scales that formed on the $Ti_3AlC_2$ were thin and rich in ${\alpha}-Al_2O_3$, whose growth rate was exceedingly slow. The $TiO_2$ was present either as the outermost surface scale or a mixture inside the ${\alpha}-Al_2O_3$-rich scale. In the $Ti_3AlC_2$, the activity and diffusivity of Ti were low, whereas those of Al were high. This was the main reason for the superior corrosion resistance of $Ti_3AlC_2$ over TiAl.

• 한국의학물리학회지:의학물리
• /
• 제5권2호
• /
• pp.3-12
• /
• 1994

$Na^{+}$ 이온을 주입시킨 후, $^{17}$ Cs 감마선으로 조사된 $Al_2$O$_3$ 및, $Na^{+}$ 이 주입된 $Al_2$O$_3$의 열자극 발광을 340K～620K의 온도 구간에서 측정하였다. $Na^{+}$ 이온을 주입시킨 후, $^{137}$Cs 감마선으로 조사된 $Al_2$O$_3$의 열자극 발광 곡선은 415K, 452K, 508K, 및 568K에서 TL peak를 가지는 곡선으로 분해되었다. $Na^{+}$ 이온 주입 후 $^{137}$Cs 감마선 조사된 $Al_2$O$_3$는, $Na^{+}$ 이온만 주입된 $Al_2$O$_3$와 $^{137}$Cs 감마선 만 조사된 $Al_2$O$_3$보다 각각 defect traps에 구속된 전하운반체의 밀도와 defect traps의 밀도가 증강되었기 때문에, $Na^{+}$ 이온 주입 후 $^{137}$Cs 감마선 조사된 $Al_2$O$_3$보다 각각 20배, 5배 증가되었다. 주입 이온 선량과 에너지의 증가는 defect trap 밀도의 증가를 초래함으로, 이온 주입된 시료의 열자극 발광 세기는 이온의 선량과 에너지에 의존함을 알았다. 입사 이온의 질량이 증가함에 따라 열자극 발광 세기는 기하급수적으로 급격히 감소하였고, 이것은 열자극 발광 세기가 결함 생성률 뿐만 아니라, 이온의 주입 깊이에도 밀접한 관계가 있음을 보여주었다.

• 한국세라믹학회지
• /
• 제22권1호
• /
• pp.11-18
• /
• 1985

The effect of stress induced phase transformation on $Al_2 O_3$ matrix dispersed with $ZrO_2-Y_2O_3$ has been studied. In order to determinate the mechanical properties three $Al_2O_3-ZrO_2$ composite series containing 1, 3 and 5 mole% $Y_2O_3$ were prepared. The starting materials were $Al_2O_3$ and $ZrO_2-Y_2O_3$ which was prepared from the aqueous solution of high purity $YCl_3$.$6H_2O$ and $ZrOCl_2$.$8H_2O$. Powder mixtures of $Al_2O_3-ZrO_2$ containing $Y_2O_3$ have been prepared by ball-milling with methanol and the samples were formed by isostatic press and sintered at 150$0^{\circ}C$ for 2hrs. After sintering. the specimens were polished for mechanical determination. The relative density of sintered specimens were also measured. It was found that the addition of 1, 3mole% to {{{{ { ZrO}_{2 } }} allowed full retention of the tetragonal phase in $Al_2O_3-ZrO_2$ but partially stabilized zirconia (PSZ) was produced by additions of 5 mole% $Y_2O_3$.The critical stress-intensity factor KIc of $A_2O_3-ZrO_2$ (containing 1 mole% $Y_2O_3$) composite materials increased with increasing $ZrO_2$ content, The maximum value of KIC=7Mn/$m^3$/2 at 20 mole% $ZrO_2$ exhibited about twice that of the $Al_2 O_3$ The modulus of rupture exhibited a trend similiar to KIC The maximum value of MOR was 580MN/m2. As the amount of Y2O3 increase it was observed that the maximum of KIC and MOR decreased : Additions of 3 mole% $Al_2O_3$ $Y_2O_3$ allowed the maximum of KIC 6MN/$m^3$/2 MOR 540MN/$m^2$ at 15 mole% $ZrO_2$ additions of 5 mole% $Y_2O_3$ allowed the maximum of KIC 5MN/$m^3$/2 MOR 410MN/$m^2$ at 10 mole% $ZrO_2$.

• 한국세라믹학회지
• /
• 제31권7호
• /
• pp.703-714
• /
• 1994

Sintering and microstructure of Ce-TZP/Al2O3 composite with $\alpha$-Al2O3 matrix containing dispersed 5~50 vol% ZrO2 were discussed. Sintered density was increased with elevating forming pressure in range of 6~300 MPa and about >99.2% of theoretical density was obtained at 1$600^{\circ}C$ for 2h in case of 300 MPa of 6~300 MPa uniaxially cold-pressed compacts containing 20 vol% ZrO2. All kinds of different batch composition exhibited nearly the same shrinkage behaviour with end-point shrinkage between 20 and 24%, and had the maximum shrinkage rate (0.41~0.54%/min) around 140$0^{\circ}C$. Grain growth was occurred faster in $\alpha$-Al2O3 than in {{{{ gamma }}-Al2O3 starting matrix during sintering at 1$600^{\circ}C$. Bimodal pore size distribution of interaglomerate pores with size of 0.03~0.2 ${\mu}{\textrm}{m}$ and of interaglomerate pores with size of around 60 ${\mu}{\textrm}{m}$ was obtained in Ce-TZP/$\alpha$-Al2O3 composite sintered at 130$0^{\circ}C$. But unimodal pore size distribution with around 0.1 ${\mu}{\textrm}{m}$ was observed in Ce-TZP/{{{{ gamma }}-Al2O3 composite sintered at the same temperature. Microcracks were occurred due to the tlongrightarrowm transformation of ZrO2 on cooling process.

• 한국재료학회지
• /
• 제26권8호
• /
• pp.430-437
• /
• 2016

Aluminum oxide ($Al_2O_3$) thin films were grown by atomic layer deposition (ALD) using a new Al metalorganic precursor, dimethyl aluminum sec-butoxide ($C_{12}H_{30}Al_2O_2$), and water vapor ($H_2O$) as the reactant at deposition temperatures ranging from 150 to $300^{\circ}C$. The ALD process showed typical self-limited film growth with precursor and reactant pulsing time at $250^{\circ}C$; the growth rate was 0.095 nm/cycle, with no incubation cycle. This is relatively lower and more controllable than the growth rate in the typical $ALD-Al_2O_3$ process, which uses trimethyl aluminum (TMA) and shows a growth rate of 0.11 nm/cycle. The as-deposited $ALD-Al_2O_3$ film was amorphous; X-ray diffraction and transmission electron microscopy confirmed that its amorphous state was maintained even after annealing at $1000^{\circ}C$. The refractive index of the $ALD-Al_2O_3$ films ranged from 1.45 to 1.67; these values were dependent on the deposition temperature. X-ray photoelectron spectroscopy showed that the $ALD-Al_2O_3$ films deposited at $250^{\circ}C$ were stoichiometric, with no carbon impurity. The step coverage of the $ALD-Al_2O_3$ film was perfect, at approximately 100%, at the dual trench structure, with an aspect ratio of approximately 6.3 (top opening size of 40 nm). With capacitance-voltage measurements of the $Al/ALD-Al_2O_3/p-Si$ structure, the dielectric constant of the $ALD-Al_2O_3$ films deposited at $250^{\circ}C$ was determined to be ~8.1, with a leakage current density on the order of $10^{-8}A/cm^2$ at 1 V.

• 공업화학
• /
• 제9권3호
• /
• pp.372-376
• /
• 1998

Pd를 지지체에 담지시킨 촉매($Pd/AlF_3$, $Pd/{\gamma}-Al_2O_3$)와 고체산촉매(${\gamma}-Al_2O_3$, ${\alpha}-Al_2O_3$, $AlF_3$)를 제조한 후 수소분위기에서 HCFC-142b(1-chloro-1,1-difluoroethane)의 탈염소반응을 수행하여 반응온도, 수소/HCFC-142b의 공급비(r) 및 Pd담지량 변화가 HFC-143a(1,1,1-trifluoroethane)와 HFC-152a(1,1-difluoroethane)로의 선택도에 미치는 영향을 조사하였다. 실험결과 $Pd/AlF_3$와 $Pd/{\gamma}-Al_2O_3$촉매에 의한 전환율은 각각 60%와 92%였고, 생성가스 중에서 HFC-143a로의 선택도는 각각 58%와 64%였다. 이때 최적반응조건은 반응온도, $200^{\circ}C$, 공간시간 1.05s, 수소/HCFC-142b의 공급비가 3이었다. 한편, 동일 조건하에서 ${\gamma}-Al_2O_3$와 ${\alpha}-Al_2O_3$, 그리고 $AlF_3$촉매에 의한 HCFC-142b의 생성가스로의 전환율은 각각 12%, 8%와 7%였고, 생성가스중 HFC-152a로의 선택도는 각각 94%, 92%와 90%였다.

• The Korean Journal of Ceramics
• /
• 제2권2호
• /
• pp.102-110
• /
• 1996

The Mg-PSZ/$Al_2O_3$ fibers were fabricated by the sol-gel method. The added $Al_2O_3$ amounts were varied from 5 to 20 mol%. The phase transformation studies of a drawn Mg-PSZ/$Al_2O_3$ fibers were investigated by use of X-ray diffraction, IR and Raman spectroscopy. Microstructure and tensile strength of fibers were subjected to scanning electron microscopy and tensile strength tester. When $Al_2O_3$ was added to the Mg-PSZ fibers, it was found out from the analysis of XRD patterns and Raman spectra that a small amount of crystalline spinel($MgAl_2O_4$) started to form due to the reaction between $Al_2O_3$ and MgO, at $1000^{\circ}C$, and the phase transformation temperature of $ZrO_2$ crystal phase at different sintering temperatures increased. Also, the rapid grain growth with average size of 2.0 ${\mu}m$ shown in Mg-PSZ fiber at $1500^{\circ}C$ was considerably suppressed to 0.39 ${\mu}m$ by adding $Al_2O_3$ at the same temperature. When the Mg-PSZ/$Al_2O_3$ fibers containing 5 mol% $Al_2O_3$ were sintered $800^{\circ}C$ for 1 hr, average tensile strength of fibers was 0.9 GPs at diameters of 20 to 30 ${\mu}m$, but as the sintering temperatures was increased to $1000^{\circ}C$ for 1 hr, average tensile strength of fibers increased to 1.2 GPa in the same diameter range.

• 한국세라믹학회지
• /
• 제37권9호
• /
• pp.909-914
• /
• 2000

반응금속 침투법으로 제조한 $Al_2$O$_3$/Al 복합체의 파괴특성과 손상 내구성을 침투방향성에 따라 관찰하였으며, 복합체는 $Al_2$O$_3$단일상보다 향상된 파괴인성과 Al 단일상보다 높은 경도값을 나타내었다. Vickers 압입법을 사용한 복합체의 손상형태에서는 침투방향에 따른 각각의 미세구조에 의해 상이한 특성을 나타내었으며, 헤르찌안 압입법을 사용한 복합체의 손상거동은 $Al_2$O$_3$과 Al의 중간거동을 나타내었다. 헤르찌안 압입 후 강도저하시험으로 복합체가 갖는 우수한 결함저항성을 관찰할 수 있었으며, 높은 헤르찌안 하중에서는 복합체의 강도저하 특성이 복합체의 미세구조에 의존함을 관찰할 수 있었다. 이와 함께 복합체에서의 반응금속 침투방향성, 미세구조 그리고 손상 내구성 사이 상호연관성에 대해 논의하였다.

• 한국결정성장학회지
• /
• 제8권4호
• /
• pp.634-639
• /
• 1998

$Y_2O_3$와 $Nb_2O_5$가 첨가된 지르코니아에 입자 크기가 다른 두종류의 Al2O3를 부피비로 10~30% 첨가한 복합체를 155$0^{\circ}C$ 온도에서 5시간 소결하여 $250^{\circ}C$ 온도의 공기 분위기하에서 1000시간 혹은 $180^{\circ}C$ 온도의 0.3MPa H2O vapor pressure 분위기하에서 5시간 열처리를 하여 X-ray 회절분석 방법을 이용하여 저온 상안정성을 조사하였다. 복합체 전부 열처리 후에 정방정 상에서 단사정 상으로 상전이가 발생하지 않는 우수한 저온 상안정성이 관찰되었다. 복합체의 상아정성에 Nb 첨가가 $Al_2O_3$의 첨가보다 더 효과적이었다. 2.8$\mu$m 입자크기를 가진 Al2O3를 부피비로 20% 첨가한 복합체에서 최적의 조건이 관찰되었으며 강도와 인성값은 각각 670MPa와 7.1MPam1/2이었다. Al2O3 입자 크기가 2.8$\mu$m에서 0.2$\mu$m로 감소함에 따라 강도는 다소 증가하였으나 파괴인성값은 감소하였다.