• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.234-238
• /
• 2008

The efficiency of fiber reinforced CMC(ceramic matrix composite) on the SiC materials have been investigated, in conjunction with the fabrication process by liquid phase sintering and the characterization. LPS-$SiC_f$/SiC composites was studied with the detailed analysis such as the microstructure, sintered density, flexural strength and fracture behavior. The applicability of carbon interfacial layer has been also investigated in the LPS process. Submicron SiC powder with the constant total amount and composition ratio of $Al_2O_3,\;Y_2O_3$ as sintering additives was used in order to promote the performance of the SiC matrix material. LPS-$SiC_f$/SiC composites were fabricated with hot press under the sintering temperature and applied pressure of $1820^{\circ}C$ and 20MPa for 1hr. The typical property of monolithic LPS-SiC materials was compared with LPS-$SiC_f$/SiC composites.

• Journal of Electrical Engineering and Technology
• /
• 제13권4호
• /
• pp.1638-1643
• /
• 2018

Multi-layer ceramic capacitors as decoupling capacitor were fabricated by dielectric composition with a high dielectric constant. The fabricated decoupling capacitors were embedded in the PCB of the 10G RF transceiver module and evaluated for the characteristics of electrical noise by the level of AC input voltage. In order to further improve the electrical properties of the $BaTiO_3$ based composite, glass frit, MgO, $Y_2O_3$, $Mn_3O$, $V_2O_5$, $BaCO_3$, $SiO_2$, and $Al_2O_3$ were used as additives. The electrical properties of the composites were determined by various amounts of additives and optimum sintering temperature. As a result of the optimized composite, it was possible to obtain a density of $5.77g/cm^3$, a dielectric constant of 1994, and an insulation resistance of $2.91{\times}10^{12}{\Omega}$ at an additive content of 5wt% and a sintering temperature of $1250^{\circ}C$. After forming a $2.5{\mu}m$ green sheet using the doctor blade method, a total of 77 layers were laminated and sintered at $1180^{\circ}C$. A decoupling capacitor with a size of $0.6mm(W){\times}0.3mm(L){\times}0.3mm(T)$ (width, length and thickness, respectively) and a capacitance of 100 nF was embedded using a PCB process for the 10G RF Transceiver modules. In the range of AC input voltage 400mmV @ 500kHz to 2200mV @ 900kHz, the embedded 10G RF Transceiver modules evaluated that it has better electrical performance than the non-embedded modules.

• 자원리싸이클링
• /
• 제9권1호
• /
• pp.44-51
• /
• 2000

보오크사이트를 원료로 하여 $Al(OH)_{3}/Al_2O_3$ 를 생산하는 공정에서 발생되는 부산물인 적니를 물리.화학적으로 처리하여 중금속 이온 제거용 흡착제로 재활용하고자 하였으며, 산업적으로 적용이 쉽도록 입자형 적니흡착제를 제조하였다. 이를 위하여 적니를 주성부능로 하고 몇 가지 첨가물의 함량과 소결온도를 변화시키며 실험하여 입자형 적니흡착제를 제조하였다. 실험결과, 적니 96.0wt%에 polypropylene 2.5wt%, sodium metasilicate 10wt%, fly ash 0.5 wt%를 첨가하여 $1200^{\circ}C$ 에서 30분간 소결시켜 제조하였을 때 납 이온에 대해 가장 높은 흡착제거율을 나타내었다. 그리고 입자형 적니흡착제의 제조방법에 따라 분쇄형 적나흡착제와 비드형 적니흡착제로 구분하여 이들의 중금속 흡탈착성능을 실험하였다. 그 결과 분쇄형 적니흡착제는 비드형 적니흡착제보다 흡착제거율과 탈착율이 모두 우수하였으며 분발형 적니흡착제와 마찬가지로 $Pb^{2+}$ 이온의 흡착제거율이 우수함을 알 수 있었다.

• 한국분말재료학회지
• /
• 제3권2호
• /
• pp.97-103
• /
• 1996

The densification of the compacts of pure Co, Fe+50%.Co and Fe+25% Co sintered under H$_2$ gas or in vacuum was investigated. The effects of AL, Nb, Ti, and V additions on the densification were also studied. The sintered compact of Co was fully-dense when the density of the compact was lower than $Dg^c$. However, above $Dg^{c}$, it was never fully-dense regardless of sintering atmosphere, temperature, and time. The densification of sintered compacts of Fe-50% Co and Fe-25% Co were always incomplete. While the addition of AL made all compacts fully-dense, the addition of Ti was effective for the compacts of Co and Fe-25% Co. V was effective only for the Fe-25% Co. These results tell us that the particle size of Co powder, the amount of Fe, and the amount of additives forming stable oxides play on important role for the complete densification. Therefore it is desirable to reduce or eliminate the equilibrium pressure of H$_{2}$O or CO in isolated pores to obtain a fully-dense sintered compact.

• 한국세라믹학회지
• /
• 제39권1호
• /
• pp.51-56
• /
• 2002

고순도 알루미나 분말에 소결조제로서 초산 마그네슘과 질산 마그네슘을 1000ppm첨가하여 제작한 소결체에 대해서 소결조제로 사용한 MgO의 출발물질의 종류가 소결체 특성에 미치는 영향을 고찰하였다. 초산 마그네슘과 질산 마그네슘을 사용해서 제작한 소결체에 대해서 소결온도 1$600^{\circ}C$에서 상대밀도의 급격한 감소가 확인되었고 SEM관찰결과 소결조제로 사용한 두 종류의 출발물질을 첨가한 경우에 동일하게 소결체의 outer layer에서는 입성장 및 기공이 형성되어있고 inner layer에서는 알루미나 입계에 제2상의 존재가 관찰되었다. 이 시편의 EPMA을 이용한 원소분석결과로부터 소결온도 1$600^{\circ}C$에서 알루미나 입계에 존재하는 제2상은 Mg를 함유한 혼합물이라는 것을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권2호
• /
• pp.135-141
• /
• 2013

본 연구에서는 CaO-$SiO_2-Al_2O_3$가 다량 함유된 산업폐기물과 산업부산물을 소성하여 개발한 분말형 속경성 분말을 초기강도의 향상을 위해 기능성 분쇄조제로 처리하여 분쇄한 속경성 미분말을 제조하였다. 이렇게 제조된 미분말을 BFS 분말과 일정비율로 혼합한 후, 시멘트에 첨가하여 모르타르 압축강도 실험을 실시하였다. 그 결과 BFS 조기강도 향상 실험 (Series I)에서는 클링커 분쇄시 기능성 분쇄조제가 첨가되어 분쇄된 속경재가 혼합된 BFS의 초기강도 발현이 우수하며 OPC 조기강도 향상 실험 (Series II)에서는 Clinker-C에 본 실험의 기능성 분쇄조제가 첨가되어 분쇄된 속경성의 분말형 자극제가 첨가된 경우에 가장 압축강도가 높은 사실을 알 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.204-209
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, $SiC_f/SiC$ composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing fiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of $SiC_f/SiC$ composites by hot pressing method. In the present work, Monolithic LPS-SiC was fabricated by hot pressing method in Ar atmosphere at 1760 $^{\circ}C$, 1780 $^{\circ}C$, 1800 $^{\circ}C$ and 1820 $^{\circ}C$ under 20 MPa using $Al_2O_3-Y_2O_3$ system as sintering additives in order to low sintering temperature. The starting powder was high purity ${\beta}-SiC$ nano-powder with an average particle size of 30 nm. Monolithic LPS-SiC was evaluated in terms of sintering density, micro-structure, flexural strength, elastic modulus and so on. Sintered density, flexural strength and elastic modulus of fabricated LPS-SiC increased with increasing the sintering temperature. In the micro-structure of this specimen, it was found that grain of sintered body was grown from 30 nm to 200 nm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1228-1229
• /
• 2008

The composites were fabricated 61[vol.%] ${\beta}$-SiC and 39[vol.%] $TiB_2$ powders with the liquid forming additives of 12[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressure or pressureless annealing at 1,650[$^{\circ}C$] for 4 hours. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the SiC-$TiB_2$ electroconductive ceramic composites. Phase analysis of SiC-$TiB_2$ composites by XRD revealed mostly of ${\alpha}$-SiC(6H), $TiB_2$, and In Situ $YAG(Al_5Y_3O_{12})$. The relative density, the flexural strength and the Young's modulus showed the highest value of 88.32[%], 136.43[MPa] and 52.82[GPa] for pressure annealed SiC-$TiB_2$ composites at room temperature. The electrical resistivity showed the lowest value of 0.0162[${\Omega}{\cdot}cm$] for pressure annealed SiC-$TiB_2$ composite at 25[$^{\circ}C$]. The electrical resistivity of the pressure annealed SiC-$TiB_2$ composite was positive temperature coefficient resistance (PTCR) but the electrical resistivity of the pressureless annealed SiC-$TiB_2$ composites was negative temperature coefficient resistance(NTCR) in the temperature ranges from 25[$^{\circ}C$] to 700[$^{\circ}C$].

• 한국세라믹학회지
• /
• 제36권10호
• /
• pp.1094-1101
• /
• 1999

Liquid phase sintered silicon carbides were obtained by sintering of $\alpha$-SiC and $\beta$-SiC powders as starting materials at 2173K and 2273K respectively. The SiCplatelet seeds of different sizes were obtained by a repeated ball milling and sedimentation. Their mean size (d50) were 2.217 ${\mu}{\textrm}{m}$ 13.67 ${\mu}{\textrm}{m}$, 22.17${\mu}{\textrm}{m}$ respectively 6wt%Al2O3-4 wt% Y2O3 was used as the sintering additives for the liquid phase sintering. The two silicon carbides had a bimodal microstructure consisting of small matrix grains and large platelike grains when the SiCplatelet seeds were added. In the case of the $\beta$-SiC the appreciable phase transformation occurred as sintering temperature increased from 2173K to 2273K and resulted in matrix shape change from equiaxed into platelike grains. In contrast there was no shape change for the $\alpha$-SiC. The size of large grains in the $\alpha$-SiC of large grains in the $\alpha$-SiC was larger than that of the large grains in the $\beta$-SiC These results suggested that the growth of the $\alpha$-SiCplatelet in the $\alpha$-SiC matrix was more favored than that of the $\alpha$-SiCplatelet in the $\beta$-SiC matix. The three point flexural strength decreased as the added seed size increased. Fracture toughness values of samples sintered at 2273K were higher than those of samples sintered at 2173K.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.181-184
• /
• 2006

Nano Infiltration Transient Eutectic Phase - Silicon Carbide (NITE-SiC) and $SiC_f/SiC$ composite have been fabricated by a Hot Pressing (HP) process, using SiC powder with an average size of about 30nm. Alumina ($Al_2O_3$) and Yttria ($Y_2O_3$) were used for additives materials. These mixed powders were sintered at the temperature a of $1300^{\circ}C$, $1650^{\circ}C$, $1800^{\circ}C$ and $1900^{\circ}C$ under an applied pressure of 20MPa. And unidirection and two dimension woven structures of $SiC_f/SiC$ composites were prepared starting from Tyranno SA fiber. Densification of microstructure gives an effect to density. Specially, Densification Mechanism basically is important from the sintering which use the HP. In this study, the densification of NITE-SiC and $SiC_f/SiC$ composite mechanism by a press displacement appears investigated. The mechanism on the densification of each sintering temperature was investigated. The each step is shows a with each other different mechanism quality.