• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.8-16
• /
• 2006

The research was conducted to characterize of Rh-Pd-Pt TWC with a double-layer washcoat for gasoline vehicle. The physical characteristics on surface of catalyst were inspected by BET, SEM and TEM. The characteristics of catalytic reaction were examined by the TPD/TPR and CO-pulse chemisorption. The catalyst $6Hx(0.35\times11\times3)$ showed superior conversion performance after hydrothermal aging process, which was due to small difference of the surface area between. the fresh and the aged catalyst. The CO-chemisorption and surface area were superior in the 600 cpsi catalyst than other catalysts, this catalyst also shown the higher conversion efficiency of the exhaust emissions. From the TPR test, the conversion performance of the aged catalyst was decreased by the agglomeration and sintering of the PM and metal oxides. From the TPD result, it was found that the NO chemisorption was happed on the bottom-layer washcoat with Pd, and the NO chemisorption was re-happened on the upper-layer washcoat with Pt and Rh in the desorption process.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• 항공우주기술
• /
• 제10권2호
• /
• pp.133-145
• /
• 2011

본 논문은 2008년 8월초부터 2010년 6월 10일 KSLV-I 2차 발사까지 수행된 나로우주센터의 추진제 및 고압가스 품질 관리 결과를 정리한 것이다. 품질관리는 나로우주센터에서 사용되는 모든 고압가스(Air, GHe, $GN_2$) 및 액화가스(LOX, $LN_2$)를 대상으로 관련 발사대 및 조립동 모든 장비에 대해 자율시험(AT), 인증시험(QT), 비행시험(FT) 모든 단계에서 수행하였다. 결과로써 총 428회의 간이검사(check analysis), 111회의 전항목검사(full analysis)를 수행하였다.

• Agricultural and Biosystems Engineering
• /
• 제3권2호
• /
• pp.73-78
• /
• 2002

Cabbage is one of the most important vegetable in Korea. The cabbage production was mainly based on human labor A comprehensive research fur substituting the human labor by machines has been performed until now. In general, cabbage is cultivated on hillside in Korea. Picking up the harvested cabbages in field and carrying to a vehicle fur transportation are very laborious work. Manual transportation of cabbage is likely to damage the quality and is also a cause to increase the cost of cabbage production. This study was to develop and evaluate a prototype cabbage loader fur efficient and safe transportation of cabbage. The developed loader was a semi-tracked vehicle operated by a hydraulic system, allowing the safe transportation and loading of cabbage in a steep field. The maximum loading weight of the loader was 1.0 ton. By using two sets of safety devices attached to the loader to avoid the roll-over in a steep field, the static rollover slopes were increased up to 34.0% and 37.4% fur the left and the rear direction, respectively The maximum field speed was about 6km/hr with two cabbage pallets of 750kg at a 25% inclined field. The loading capacity of the loader was about 35 pallets/hr when picking up, carrying, and unloading two cabbage pallets for one loading operation. The loading capacity was more than 8 times in comparison with the conventional human labor. The developed loader could be used fur loading and carrying the other vegetables. The study suggested a possible approach for designing the field machines operated on hillside.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.480-488
• /
• 2000

Cabbage is the most important vegetables in korea. The cabbage production was based on arduous human labor. A comprehensive research for substituting the human work by machines has been performed at present. In general, cabbage is cultivated on hillside in korea. The harvested cabbage in a field and carrying it to a vehicle for transportation are very laborious work. Hand labor in cabbage transportation to the market damages the quality of cabbage and is also a cause to increase the cost of cabbage production. This study was to design and evaluate a prototype cabbage loader for deserving efficient and safe transportation of cabbage. The developed cabbage loader was a semi-tracked vehicle operated by a hydraulic system, allowing the safe transporting and the loading of cabbage in a steep field. The maximum loading capacity of the loader was 1.0 ton. By using safety devices attached to the loader, the static slopes were 34.0% and 37.4% for the left and the rear roll-over, respectively. The maximum field speed was about 6km/hr with two cabbage pallets of 750kg at a 25% inclined field. The field capacity was about 35 pallets/hr in case of picking up, carrying and unloading two cabbage pallets. The field efficiency of the loader was analyzed to be more than 8 times in comparison of the conventional human labor. The developed loader would be applied for loading and carrying the other vegetables due to the similarity of operations. The study suggested a standard approach to the design of field machines operated in a steep field.

• 한국입자에어로졸학회지
• /
• 제7권1호
• /
• pp.21-30
• /
• 2011

The spatial distributions of air pollutants, in particular, ultrafine particles near traffic congestion roads at urban areas need to reduce human exposure levels for protecting public health. In this study, the number concentrations of ultrafine particles larger than 5 nm were measured every second during driving on the major roads of Nowon-gu, Seoul for 1.6 h using a mobile emission laboratory on October 5, 2010. The ultrafine particle number concentrations ranged from 7,009 to $265,600particles/cm^3$ with an average of $55,570particles/cm^3$, and these levels were comparable to concentrations of ultrafine particles larger than 3 or 7 nm on the arterial roads at urban areas in Los Angeles, USA and Zurich, Switzerland. It was frequently observed that the ultrafine particle number increased rapidly when vehicle speed was accelerated and it decreased sharply when vehicle speed was decelerated. The high peak events of ultrafine particle concentration larger than $200,000particles/cm^3$ were observed seven times during the measurement period. From the three repeated measurements during the short period of 50 min, it was concluded that the ultrafine particle number concentration on the road was significantly time-dependent. This on-road measurement approach can be utilized to manage vehicle-related air pollution in urban.

• 한국표면공학회지
• /
• 제41권3호
• /
• pp.121-128
• /
• 2008

High strength 7xxx aluminum alloys have been applied to automotive bump back beam of the some limited model for light weight vehicle. The aluminum bump back beam is manufactured through extrusion, bending and welding. The residual stress given on these processes combines with the corrosive atmosphere on the road spreaded with corrosive chemicals to melt snow to occur the stress corrosion cracking. The composition of commercial 7xxx aluminum has Zn/Mg ratio about 3 and Cu over 2 wt% for better strength and stress corrosion cracking resistivity. But this composition isn't adequate for appling to the automotive bump back beam with high resistance to extrusion and bad weldability. In this study the composition of 7xxx aluminum alloy was modified to high Zn/Mg ratio and low Cu content for better extrusion and weldability. To estimate the resistivity against stress corrosion cracking of this aluminum alloy by slow strain rate test, the corrosion atmosphere and strain rate separate the stress corrosion cracking from conventional corrosion must be investigated. Using 0.6 Mol NaCl solution on slow strain rate test the stress corrosion cracking induced fracture was not observed. By adding 0.3% $H_2O_2$ and 0.6M $Na_2SO_4$ to 1M NaCl solution, the corrosion potential and current density of polarization curve moved to active potential and larger current density, and on the slow strain rate test the fracture energy in solution was lower than that in pre-exposure. These mean the stress corrosion cracking induced fracture can be estimated in this 1M NaCl + 0.3% $H_2O_2$ + 0.6M $Na_2SO_4$ solution. When the strain rate was below $2{\times}10^{-6}$, the stress corrosion cracking induced fracture start to be observed.

• 한국도로학회논문집
• /
• 제17권6호
• /
• pp.37-45
• /
• 2015

PURPOSES : The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridge-type concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads. METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results. RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual-wheel loading condition by accelerating pavement tester. CONCLUSIONS : Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.

• 한국산학기술학회논문지
• /
• 제16권6호
• /
• pp.3919-3925
• /
• 2015

방사성옥소 치료를 받은 환자가 격리 후 차량으로 귀가할 때 동승자가 받는 방사선 피폭량을 줄이기 위해서는 동승하는 시간을 적절하게 제한해야 한다. 계산 방법이 어렵기 때문에 현재까지 일반적인 가이드라인은 있어도 환자 개개인의 상태를 반영하는 기준은 없었다. 그런데 비교적 짧은 이동시간 동안에는 소변을 통한 배출이 없고 물리적인 붕괴도 없다는 가정을 하면 총선량 = 선량율 ${\times}$ 이동시간이라는 아주 간편한 계산을 할 수 있다. 입원했던 환자 120명의 데이터를 활용하여 이 간편계산법과 표준적인 계산법으로 계산한 결과를 비교하였다. 이동가능 시간을 계산했을 때 간편계산의 결과는 표준적인 방법에 비해 0.3 m 거리에서는 56%, 0.5 m 거리에서는 91%, 1 m 거리에서는 96%였다. 간편계산법은 안전한 방법이며, 방사선안전관리 방법으로 쉽게 적용할 수 있을 것이다. 또한 방사성옥소 치료를 받는 갑상선기능항진증 환자에서도 적용이 가능하다.

• 대한교통학회지
• /
• 제30권6호
• /
• pp.71-80
• /
• 2012

본 연구에서는 개별차량의 구간통행시간 정보를 이용한 독립교차로의 실시간 신호제어 알고리즘을 개발하였다. DSRC와 같이 개별차량의 ID와 검지시각 정보를 수집할 수 있는 검지체계를 적용하였으며, 개별차량의 통행시간 정보로 부터 도착교통류율, 지체, 적색시간 변화에 따른 지체 변화량을 산정하기 위한 모형을 정립하였다. 통행시간기반 신호제어 알고리즘은 교차로 지체를 최소화 시키기 위한 현시별 적색시간 변화량을 결정하며, 선형계획모형을 적용하여 신호시간의 최적화 과정을 수행한다. 알고리즘의 효과평가를 위해 CORSIM과 RUN TIME EXTENSION을 적용한 미시적 시뮬레이션 분석을 시행하였으며, 이동류의 포화상태를 확인하여 지체 최소화를 위한 신호시간이 산정됨을 확인하였다. 또한 Probe 차량의 비율에 따라 이동류의 지체추정 성능을 확인하였으며, 특정 시나리오에 한정된 결과이나 40% 이상 Probe 차량 비율이 확보되는 경우 효과적 신호제어가 가능함을 확인하였다. 최근 국내 교통관리분야에서는 하이패스, 첨단교통관리시스템(ATMS), 광역교통정보사업(UTIS) 등 개별차량의 구간정보를 수집할 수 있는 검지체계가 급격히 확산되고 있으며, 본 연구는 실시간 신호운영 분야에서 검지체계의 변화를 수용하기 위한 방안으로서 새로운 형태의 신호제어 방법론을 제시하였다는데 의의가 있겠다.