• 열처리공학회지
• /
• 제16권6호
• /
• pp.320-328
• /
• 2003

A specimen of Cu-35%Sn alloy has been subjected to the unidirectional heat treatment in an attempt to examine the evolution of microstructures under varying thermal conditions. The specimen was cast in the form of a cylinder 10 mm in diameter and 200 mm in length, which was then installed in the temperature gradient field established inside a vertical tube furnace. The furnace temperature was adjusted to make the upper part at $750^{\circ}C$ and bottom end part at $300^{\circ}C$ of the specimen. The experiment was terminated by dropping it into water after the 30 minutes holding at given temperature. By the rapid cooling, the high temperature phases, ${\gamma}$ and ${\zeta}$, were retained at ambient temperature with some of ${\gamma}$ phase transformed to ${\varepsilon}$ phase, especially at the grain boundaries of ${\gamma}$ phase. The presence of ${\varepsilon}$ phase was found to determine the nature of phase transformations of the ${\zeta}$ phase undergoes upon cooling. In the close area of the ${\varepsilon}$ phase, ${\varepsilon}$ phase grew separately out of ${\zeta}$, and adds to the preexisting ${\varepsilon}$ whereas in areas away from ${\varepsilon}$, both ${\delta}$ and ${\varepsilon}$ grew simultaneously out of ${\zeta}$, and formed a lamella eutectoid structure. The transformation to ${\delta}$ was found to occur only in slow cooling. The hardness on each phase showed that the retained phases, ${\gamma}$ and ${\zeta}$, could be plastically deformed without brittle fracture while the phases, ${\varepsilon}$ and ${\delta}$, were too brittle to be deformed.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.9-17
• /
• 2000

준안정상인 $\beta$형 HNIW의 용해와 안정상인 $\varepsilon$형 HNIW의 성장 특성을 고려한 모델식을 물질수지와 한께 계산하는 방법으로 결정성장 속도와 용해 속도를 계산하였다. 제시된 모델은 용액을 매체로 하여 진행되는 $\beta$$\longrightarrow$$\varepsilon$전이 현상에 대한 속도론적 데이터를 모사 하는데 유용하였다. 2 단 모델을 이용한 유효 인수로부터, 격정성장 과정에서 표면 축적 단계의 영향은 작으며, 확산 의존성은 ethyl acetate와 chloroform의 혼합 용매 중 chloroform의 함량이 증가함에 따라 감소함을 보였다. 이들 속도론 적 계수들을 이용한 수치모사를 통하여 $\varepsilon$-HNIW의 입자 크기를 예측하는 것이 가능하였다.

• 한국재료학회지
• /
• 제22권7호
• /
• pp.342-345
• /
• 2012

The dielectric properties and phase transformation of poled <001>-oriented $Pb(Mg_{1/3}Nb_{2/3})O_3-x%PbTiO_3$(PMN-x%PT) single crystals with compositions of x = 20, 30, and 35 mole% are investigated for orientations both parallel and perpendicular to the [001] poling direction. An electric-field-induced monoclinic phase was observed for the initial poled PMN-30PT and PMN-35PT samples by means of high-resolution synchrotron x-ray diffraction. The monoclinic phase appears from $-25^{\circ}C$ to $100^{\circ}C$ and from $-25^{\circ}C$ to $80^{\circ}C$ for the PMN-30PT and PMN-35PT samples, respectively. The dielectric constant (${\varepsilon}$)-temperature (T) characteristics above the Curie temperature were found to be described by the equation$(1/{\varepsilon}-1/{\varepsilon}_m)^{1/n}=(T-T_m)/C$, where ${\varepsilon}_m$ is the maximum dielectric constant and $T_m$ is the temperature giving ${\varepsilon}_m$, and n and C are constants that change with the composition. The value of n was found to be 1.82 and 1.38 for 20PT and 35PT, respectively. The results of mesh scans and the temperature-dependence of the dielectric constant demonstrate that the initial monoclinic phase changes to a single domain tetragonal phase and a to paraelectric cubic phase. In the ferroelectric tetragonal phase with a single domain state, the dielectric constant measured perpendicular to the poling direction was dramatically higher than that measured in the parallel direction. A large dielectric constant implies easier polarization rotation away from the polar axis. This enhancement is believed to be related to dielectric softening close to the morphotropic phase boundary.

• Journal of Microbiology and Biotechnology
• /
• 제21권6호
• /
• pp.652-658
• /
• 2011

The growth kinetics of Streptomyces noursei NRRL 5126 was investigated under different aeration and agitation combinations in a 5.0 l stirred tank fermenter. Poly-${\varepsilon}$-lysine biosynthesis, cell mass formation, and glycerol utilization rates were affected markedly by both aeration and agitation. An agitation speed of 300 rpm and aeration rate at 2.0 vvm supported better yields of 1,622.81 mg/l with highest specific productivity of 15 mg/l.h. Fermentation kinetics performed under different aeration and agitation conditions showed poly- ${\varepsilon}$-lysine fermentation to be a growth-associated production. A constant DO at 40% in the growth phase and 20% in the production phase increased the poly-${\varepsilon}$-lysine yield as well as cell mass to their maximum values of 1,992.35 mg/l and 20.73 g/l, respectively. The oxygen transfer rate (OTR), oxygen utilization rate (OUR), and specific oxygen uptake rates ($qO_2$) in the fermentation broth increased in the growth phase and remained unchanged in the stationary phase.

• 열처리공학회지
• /
• 제13권3호
• /
• pp.143-150
• /
• 2000

Ferritic plasma nitrocarburising was performed on pure iron using a modified DC plasma unit. This investigation was carried out with various gas compositions which consisted of nitrogen, hydrogen and carbon monoxide gases, and various gas pressures for 3 hours at $570^{\circ}C$. After treatment, the different cooling rates(slow cooling and fast cooling) were used to investigate its effect on the structure of the compound layer. The ${\varepsilon}$ phase occupied the outer part of the compound layer and ${\gamma}^{\prime}$ phase existed between the ${\varepsilon}$ phase and the diffusion zone. The gas composition of the atmosphere influenced the constitution of the compound layer produced, i.e. high nitrogen contents were essential for the production of ${\varepsilon}$ phase compound layer. It was found that with increasing carbon content in the gas mixture the compound layer thickness increased up to 10%. In the gas pressure around 3 mbar, the compound layer characteristics were slightly effected by gas pressure. However, in the low gas pressure and high gas pressure, the compound layer characteristics were significantly changed. The constitution of the compound layer was altered by varying the cooling rate. A large amount of ${\gamma}^{\prime}$ phase was transformed from the ${\varepsilon}$ phase during slow cooling.

• 한국진공학회지
• /
• 제9권4호
• /
• pp.436-441
• /
• 2000

플라즈마 침질탄화처리는 보통탄소강, 저합금강 등에 내마모성, 내식성 및 내피로성 향상에 사용되어 있으며 자동차 부품, 기계류 부품, 공업용 공구 등에 적용할 수 있는 표면경화열처리이지만 내마모성 및 내식성을 향상시키는 단상의 $\varepsilon$ 화합물층을 생성시키기는 어려운 문제점으로 남아 있다. 따라서 본 연구에서는 탄소강과 저합금강에 대해 질소와 $CH_4$ 가스농도를 변화시켜 플라즈마 침질탄화처리를 실시하여 단상의 $\varepsilon$ 화합물층 생성가능성과 시간을 변화시켜 화합물층의 생성과정을 고찰하였다. $\varepsilon$ 화합물층은 질소농도가 증가할수록 형성이 용이하였고 $CH_4$ 가스 농도가 증가할수록 $\varepsilon$ 화합물층의 형성이 용이하였지만 시멘타이트상이 생성되었다. 화합물층은 10분이 경과한 후 생성되었고 $\gamma$'상으로부터 시작되었으며 처리시간이 10시간 이상이 되면 화합물층내에 시멘타이트상이 생성되어 화합물층의 두께가 감소하였다.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.101-107
• /
• 1998

A three-dimensional multi-phase flow is simulated around a smooth tire. This simulation is conducted by solving Navier-Stokes equation with a k-$\varepsilon$ turbulent model. The numerical calculations are carried out by modeling a multi-phase free surface flow mixed with air and water at the inlet. The numerical solutions show an intuitively resonable behavior of water around a moving tire. The calculated pressure around the tire surface along the moving direction is presented. The moving velocities of the tire are chosen to be 30, 40, 60, and 70 km/h. The numerically simulated pressures around the tire are compared with existing experimental data. The comparison shows a new possible tool of analyzing a hydroplaning phenomenon for an automobile tire by means of a computational fluid dynamics.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.312-316
• /
• 1999

The interfacial structure of duplex treated AISI 4140 consisting of iron nitride and TiN layer was characterized by optical microscope, SEM and XRD. A black layer was formed from the decomposition of iron nitride during Ti ion bombardment. The black layer was characterized as an a-Fe phase transformed from the iron nitride by XRD. In order to identify the formation mechanism of the black layer, a thermal analysis of iron nitride undertaken by DSC method. As an iron nitride was mostly consisted of ${\gamma}$'-Fe$_4$N and $\varepsilon$-$Fe_3$N phase after plasma nitriding, in this study, a ${\gamma}$'$-Fe_4$N and $\varepsilon$-$Fe_3$N powders were separately prepared by the different processing conditions of gas nitriding of iron powder in the fluidized bed. From the DSC thermal analysis, the phase transformation of ${\gamma}$'$-Fe_4$N, $\varepsilon$-$Fe_3$N was followed the path of transformation; $ \Upsilon{'}-Fe_4$Nlongrightarrow${\gamma}$-Felongrightarrowa-Fe and of $\varepsilon$-$Fe_3$Nlongrightarrow$\varepsilon$-$Fe_{2.5}$ /N+${\gamma}$'$-Fe_4$Nlongrightarrow${\gamma}$'-Fe$_4$Nlongrightarrow${\gamma}$longrightarrowFelongrightarrowalongrightarrowFe, respectively. It explains the reason why the $\varepsilon$ $-Fe_3$N phase disappeared in the first time and then ${\gamma}$'-Fe$_4$N in the formation of the black layer in the duplex coating.

• 한국재료학회지
• /
• 제12권6호
• /
• pp.427-430
• /
• 2002

Plasma nitrocarburizing treatment was performed for SCM 435 steel by using a plasma ion nitriding system. The effects of the variation of nitrogen and methan contents upon the hardened layer was investigated. Both the thickness of the compound layer and the amount of $\varepsilon$ phase in the compound layer increased with increasing nitrogen content. However, the thickness of the compound layer decreased due to unstable plasma for an atmosphere containing 90% $N_2$ gas content in the gas mixture. The amount of $\varepsilon$phase in the compound layer increased with increasing $CH_4$ gas content. For $CH_4$ gas content more than 2% in the gas mixture, the thickness of the compound layer decreased due to the formation of $\theta$ phase.

• Korean Chemical Engineering Research
• /
• 제48권3호
• /
• pp.359-364
• /
• 2010

직경이 0.152 m인 삼상슬러리 기포탑에서 연속 슬러리상 영역(${\varepsilon}_f$), 기포영역(${\varepsilon}_b$) 그리고 기포의 후면에서 기포와 같이 상승하는 소용돌이 영역인 wake 영역(${\varepsilon}_w$)의 세 종류의 기능영역을 분류하여 이들 각 영역의 체류량을 구하였다. 기포탑에서 기포영역과 wake 영역의 체류량은 전기저항 탐침법에 의해 결정하였다. 기체유속($U_G$)과 슬러리상에서 고체입자의 농도($S_c$)가 삼상슬러리 기포탑에서 각 기능영역의 체류량에 미치는 영향을 검토하였다. 슬러리 기포탑에서 기체유속이 증가하면 연속 슬러리상의 체류량은 감소하였으나, 기포와 wake의 체류량은 증가하였다. 슬러리상에서 고체입자의 농도가 증가함에 따라 연속 슬러리상 영역의 체류량은 증가하였으나, 기포와 wake 영역의 체류량은 감소하는 경향을 나타내었다. wake 영역의 체류량은 기포영역 체류량의 15~40% 정도를 나타났으며, 기체유속이 증가함에 따라 wake 영역의 기포영역에 대한 분율은 감소하였다. 본 연구의 범위에서 세 기능영역의 체류량은 각각 실험 변수의 상관식으로 나타낼 수 있었다.