• 제목/요약/키워드: ${\gamma}'$ phase

검색결과 689건 처리시간 0.026초

High Velocity Oxygen Fuel 공정으로 제조된 Ni 계 자용성 복합 코팅 소재의 미세조직과 마모 특성에 미치는 고주파 열처리의 영향 (Effect of High Frequency Heat Treatment on the Microstructure and Wear Properties of Ni based Self Fluxing Composite Coating Layer Manufactured by HVOF Spray Process)

  • 위동열;함기수;박순홍;이기안
    • 한국분말재료학회지
    • /
    • 제26권5호
    • /
    • pp.421-431
    • /
    • 2019
  • In this study, the formation, microstructure, and wear properties of Colmonoy 88 (Ni-17W-15Cr-3B-4Si wt.%) + Stellite 1 (Co-32Cr-17W wt.%) coating layers fabricated by high-velocity oxygen fuel (HVOF) spraying are investigated. Colmonoy 88 and Stellite 1 powders were mixed at a ratio of 1:0 and 5:5 vol.%. HVOF sprayed self-fluxing composite coating layers were fabricated using the mixed powder feedstocks. The microstructures and wear properties of the composite coating layers are controlled via a high-frequency heat treatment. The two coating layers are composed of ${\gamma}-Ni$, $Ni_3B$, $W_2B$, and $Cr_{23}C_6$ phases. Co peaks are detected after the addition of Stellite 1 powder. Moreover, the WCrB2 hard phase is detected in all coating layers after the high-frequency heat treatment. Porosities were changed from 0.44% (Colmonoy 88) to 3.89% (Colmonoy 88 + ST#1) as the content of Stellite 1 powder increased. And porosity is denoted as 0.3% or less by inducing high-frequency heat treatment. The wear results confirm that the wear property significantly improves after the high-frequency heat treatment, because of the presence of well-controlled defects in the coating layers. The wear surfaces of the coated layers are observed and a wear mechanism for the Ni-based self-fluxing composite coating layers is proposed.

열기계적 피로에 따른 단결정 니켈기 초내열합금의 변형 및 파괴거동 (Deformation and Failure Behavior during Thermo-Mechanical Fatigue of a Nickel-Based Single Crystal Superalloy)

  • 강정구;홍현욱;최백규;김인수;강남현;조창용
    • 대한금속재료학회지
    • /
    • 제49권2호
    • /
    • pp.112-120
    • /
    • 2011
  • The out-of-phase thermo-mechanical fatigue (OP TMF) in a <001> oriented single crystal nickel-based superalloy CMSX-4 has been studied. OP TMF life was less than a half of low cycle fatigue(LCF) life in spite of a small hysteresis loop area of OP TMF compared to that of LCF. The failure was caused by the initiation of a crack at the oxide-layered surface followed by its planar growth along the <100> ${\gamma}$ channel in both LCF and OP TMF. However, deformation twins appeared near the major crack of OP TMF. The multiple groups of parallel twin plates on {111} planes provided a preferential path for crack propagation, which caused a significant decrease in OP TMF life. Additionally, the analysis on the surface crack morphology revealed that the tensile strain at the minimum temperature of OP TMF was found to accelerate the crack propagation.

ASTM Gr.92강의 미세조직 및 기계적 성질에 미치는 템퍼링 온도 및 열처리경로의 영향 (Effects of Tempering Temperature and Heat-Treatment Path on the Microstructural and Mechanical Properties of ASTM Gr.92 Steel)

  • 김연근;한창희;백종혁;김성호;이찬복;홍순익
    • 대한금속재료학회지
    • /
    • 제48권1호
    • /
    • pp.39-48
    • /
    • 2010
  • In order to investigate the effects of tempering temperature and heat-treatment path on the microstructural and mechanical properties of ASTM Gr.92 steels, four samples with different tempering temperatures and heat-treatment paths wer prepared. THeree experimental steels showed tempered martensitic microstructures, but the sample tempered at $810^{\circ}C$ was presumed to retain partially untempered martensitic microstructures due to a lower ${\alpha}$+${\gamma}$ phase regime. $M_{23}C_6$, V(C,N), and Nb(C,N) precipitates were observed in all samples. In addition $Cr_2N$ was observed to be precipitated finely and uniformly by isothermal heat-treatment. The lath width and precipitate size in the isothermal heat-treated samples were much smaller than those of the tempered-only specimens. Because of a fine and uniform precipitate, a reduction of lath width would enhance precipitation hardeing, and it was shown that mechanical propertiesincluding the hardness and tensile properties of the steels were improved by isothermal heat-treatment.

베이지안 추론 기반 니켈기 초합금의 열화도 정량화 방법과 열화도 및 크리프 수명 예측의 방법 (Degradation Quantification Method and Degradation and Creep Life Prediction Method for Nickel-Based Superalloys Based on Bayesian Inference)

  • 유준상;오하영
    • 한국정보통신학회논문지
    • /
    • 제27권1호
    • /
    • pp.15-26
    • /
    • 2023
  • 본 연구의 목적은 고온부품의 소재로 사용하는 니켈기 초합금인 DA-5161 SX에 대한 크리프시험으로 얻은 시편 의 주사전자현미경으로 촬영한 미세조직 단면의 이미지로부터 인공지능 기반 열화인덱스(Degradation Index)로 정 량화 하는 새로운 방법을 제시하고 운전 중인 기기의 고온부품의 구성품을 파괴하지 않고 베이지안 추론 기반 열화 도를 예측하는 모델과, Larson-Miller Parameter(LMP)를 예측하여 크리프 수명 예측 모델을 제안하는 것이다. 니켈 기 초합금 미세조직인 감마프라임 상(γ')의 기하학적 특징 및 베이지안 추론 기반으로 소량의 이미지로 일관성 있는 대푯값을 추론하는 새로운 열화인덱스 방법과 고온부품을 파괴하지 않고 소재의 환경조건 정보만으로 열화인덱스 와 LMP를 예측할 수 있는 방법을 제안한다.

Circumstellar Clumps in the Cassiopeia A Supernova Remnant: Prepared to be Shocked

  • Koo, Bon-Chul;Kim, Hyun-Jeong;Oh, Heeyoung;Raymond, John C.;Yoon, Sung-Chul;Lee, Yong-Hyun;Jaffe, Daniel T.
    • 천문학회보
    • /
    • 제45권1호
    • /
    • pp.43.1-43.1
    • /
    • 2020
  • Cassiopeia A (Cas A) is a young supernova remnant (SNR) where we observe the interaction of SNR blast wave with circumstellar medium. From the early optical studies, dense, slowly-moving, N-rich "quasi-stationary flocculi" (QSF) have been known. These are probably dense CNO-processed circumstellar knots that have been engulfed by the SNR blast wave. We have carried out near-infrared, high-resolution (R=45,000) spectroscopic observations of ~40 QSF, and here we present the result on a QSF knot (hereafter 'Knot 24') near the SNR boundary of Cas A. The average [Fe II] 1.644 um spectrum of Knot 24 has a remarkable shape with a narrow (~8 km/s) line superposed on the broad (~200 km/s) line emitted from shocked gas. The spatial morphology and the line parameters indicate that Knot 24 has been partially destroyed by a shock wave and that the narrow line is emitted from the unshocked material heated/ionized by the shock radiation. This is the first detection of the emission from the pristine circumstellar material of the Cas A supernova progenitor. We also detected H Br gamma and other [Fe II] lines corresponding to the narrow [Fe II] 1.644 um line. For the main clump where we can clearly identify the shock emission associated with the unshocked material, we analyze the observed line ratios using a shock model that includes radiative precursor. The analysis indicates that the majority of Fe in the unshocked material is in the gas phase, not depleted onto dust grains as in the general interstellar medium. We discuss the non-depletion of Fe in QSF and its implications on the immediate progenitor of the Cas A supernova.

  • PDF

납 표준물질을 이용한 방사성동위원소 Thallium-201의 화학적 분리공정 개발 (Development of Chemical Separation Process for Thallium-201 Radioisotope with Lead Standard Material)

  • 이준영;김태현;박정훈
    • 방사선산업학회지
    • /
    • 제17권4호
    • /
    • pp.543-549
    • /
    • 2023
  • Thallium-201 (201Tl) is a medical radioisotope which emits gamma rays when it decays and used in myocardial perfusion scans in single-photon emission tomography due to its similar properties to potassium. Currently, the Korea Institute of Radiological & Medical Sciences is the only institution producing 201Tl in Korea, and optimization of 201Tl production research is necessary to meet supply compared to domestic demand. To this end, technical analysis of plating target production and chemical separation methods essential for 201Tl production research is conducted. It deals with the process of generating and separating 201Tl radioisotope and target production, It can be generated through a nuclear reaction such as natHg(p,xn)201Tl, 201Hg(p,n)201Tl, natPb(p,xn)201Bi → 201Pb → 201Tl, 205Tl(p,5n)201Pb → 201Tl, and considering impure nuclide generated simultaneously with the use of proton beam energy of 35 MeV or less, it is intended to be produced using the 203Tl(p,3n)201Pb→201Tl nuclear reaction. In particular, the chemical separation of Tl is a very important element, and the chemical separation methods that can separate it is broadly divided into four types, including solid phase extraction, liquid-liquid, electrochemical, and ion exchange membrane separation. Some chemical separations require additional separation steps, such as methods using selective adsorption. Therefore, this technical report describes four chemical separation methods and seeks to separate high-purity 201Tl using a method without additional separation steps

Streptozotocin 유도 당뇨성 흰쥐에서 methotrexate의 신독성 생성기전에 관한 연구 (The Mechanism of Nephrotoxicity Formation of Methotrexate in STZ-Induced Hyperglycemic Rats)

  • 김석환;김여정;이주연;강혜옥;이항우;최종원
    • 생명과학회지
    • /
    • 제16권2호
    • /
    • pp.259-265
    • /
    • 2006
  • 엽산과 유사한 구조를 가져 관절염 치료제로 쓰이는 methotrexate (MTX)의 당뇨병 쥐에서의 신독성 기전을 구명할 목적으로 실험동물 정상군과 STZ로 당뇨를 유발한군에 MTX률 투여하여 신장 독성을 유발하여 혈중 생화학적 변화를 관찰하고 free radical의 생성계와 해독계의 활성에 미치는 영향을 관찰하였다. 혈중 신장기능 지표 효소 및 신장조직의 지질과산화 함량이 정상군에 MTX를 투여한 군에 비해 당뇨쥐에 MTX를 투여한 군에서 현저히 증가하였다. 당뇨쥐에 MTX를 투여함으로써 활성산소 생성계인 phase I 단계 중 cytosol 효소계 활성이 정상쥐에 MTX를 투여한 군에 비하여 현저히 증가하였고, phase II 단계 중 glutathione S-transferase의 활성이 정상쥐에 MTX를 투여하였을때에 비하여 당뇨쥐에 MTX를 투여하였을때 현저히 감소하였다. 신조직 중 glutathione의 함량 또한 당뇨쥐에 MTX를 투여했을때 현저히 감소하였고 이러한 결과는 $\gamma$-glutamylcysteine synthetase와 glutathione reductase의 활성을 감소시킨 결과로 생각된다. 이상의 결과를 종합하여 볼때 당뇨쥐에 MTX를 투여하면 신독성이 증가함을 확인할 수 있었고, 그 기전은 cytosol계 효소 활성을 증가시켜 MTX의 대사계를 촉진시킴으로 독성물질의 생성을 증가시키고, 이로 인한 신조직중의 지질과산화 함량의 증가는 glutathione의 함량 감소에 의해 나타나는 결과로 사료되어진다.

ELISA방법에 의한 방사선 피폭 후 흰쥐 혈액 내에서의 ceruloplasmin 정량 (Quantification of Ceruloplasmin in Wale Rats Exposed to ${\gamma}$-radiation by Enzyme Linked Immunosorbent Assay)

  • 김민규;박선영;김국찬;이강석
    • Journal of Radiation Protection and Research
    • /
    • 제22권2호
    • /
    • pp.103-109
    • /
    • 1997
  • 수놈 흰쥐를 1.0, 2.0, 3.0, 5.0 및 7.0 Gy 선량으로 전신 조사하였으며 조사 후 48, 72, 96시간과 216시간 경과 후 혈액을 채취하였다. 혈액 내 ceruloplasmin을 측정하여 선량반응곡선을 완성하기 위하여 항원고정 방식의 경쟁적 효소면역측정법을 사용하였다. Ceruloplasmin의 정제는 turpentine을 주사한 수놈 흰쥐의 혈액을 사용하였다. Ceruloplasmin의 흡착효율은 50 mM carbonate/bicarbonate buffer, pH 9.6보다 10 mM Tris-HCI, 150 mM sodium chloride, pH 7.4에서 더 효과적이었으며 정량을 위한 적정한 ceruleplasmin의 흡착범위는 well 당 $70{\sim}140ng$이었다. Ceruloplasmin은 피폭 후 $72{\sim}96$시간에서 최대농도를 보였으며 피폭 후 96시간에서 최대값을 지니는 선량반응관계를 보였다. Cerulplasmin은 피폭 후 216시간에서도 피폭이전의 농도로 회복되지 않았다. 0.1 Gy로 피폭된 경우에도 ceruloplasmin의 농도는 피폭 후 $72{\sim}96$시간에서 최대로 증가하였으며 단백질의 농도는 대조군과 유의성 있는 변화를 관찰할 수 있었다. Cerulplasmin은 방사선피폭 후 변화하는 중요한 급성반응물질중의 하나로 밝혀졌으며 방사선방호를 위한 유전자 발현 및 조절에 관할 연구가 필요하다.

  • PDF

인천광역시에서 유통되는 계란의 플루오로퀴놀론계 항균물질 잔류 실태 조사 (A study on the residues of fluoroquinolones in hen's eggs consumed in Incheon Metropolitan city)

  • 박은정;임지흔;이성모;임정수;오대규
    • 한국동물위생학회지
    • /
    • 제31권3호
    • /
    • pp.385-395
    • /
    • 2008
  • This study was carried out to investigate the residue level of fluoroquinolones in hen's general eggs and specific eggs by microbiological assay method and high performance liquid chromatography (HPLC) method. HPLC separation was carried out by reversed phase chromatography on a Symmetry $C_{18}$ (250${\times}$4.6 mm, $5{\mu}m$ particle size) with a phase composed of distilled water (containing 0.4% triethylamine and phosphoric acid) : Methanol (780 : 220, v/v), pumped isocratically at a flow rate of 1.0ml/min. A fluorescence detector was utilized with an excitation wavelength of 278nm and an emission wavelength of 456nm. The calibration curves were linear $({\gamma}^2{\geq}0.999)$ over a concentration range of $0.025{\sim}0.4{\mu}g/ml$. Average recoveries of the five fluoroquinolones in whole eggs at fortified levels of $0.05{\sim}0.2{\mu}g/g$ were ranged mean $78.1{\sim}91.7%$ and low coefficient of variation was less than 10% for all analysed samples. The limits of detection and limits of quantification for whole eggs were $1.2{\sim}6.0ng/g$ and $2.3{\sim}9.1ng/g$, respectively. Only one hen's general eggfrom chicken farm in Incheon was detected with the residual fluoroquinolones (Microbiological assay method; 1 of 47 general eggs) ; the range of residual concentration enrofloxacin was 0.12ppm. Those in food stores were detected with the residual fluoroquinolones (Microbiological assay method; 4 of 88 general eggs) ; the ranges of residual concentration enrofloxacin were $0.15{\sim}2.2 ppm$, ciprofloxacin $0.01{\sim}0.06ppm$, and hen's specific eggs (40) in food stores were not detected. For the microbiological assay method of fluoroquinolones in hen's eggs, as the results of comparative analysis, the disc diffusion method with E coli may be a little highly detected for the residual fluoroquinolones.

Formation of a large-scale quasi-circular flare ribbon enclosing three-ribbon through two-step eruptive flares

  • Lim, Eun-Kyung;Yurchyshyn, Vasyl;Kumar, Pankaj;Cho, Kyuhyoun;Kim, Sujin;Cho, Kyung-Suk
    • 천문학회보
    • /
    • 제41권2호
    • /
    • pp.42.1-42.1
    • /
    • 2016
  • The formation process and the dynamical properties of a large-scale quasi-circular flare ribbon were investigated using the SDO AIA and HMI data along with data from RHESSI and SOT. Within one hour time interval, two subsequent M-class flares were detected from the NOAA 12371 that had a ${\beta}{\gamma}{\delta}$ configuration with one bipolar sunspot group in the east and one unipolar spot in the west embedded in a decayed magnetic field. Earlier M2.0 flare was associated with a coronal loop eruption, and a two-ribbon structure formed within the bipolar sunspot group. On the other hand, the later M2.6 flare was associated with a halo CME, and a quasi-circular ribbon developed encircling the full active region. The observed quasi-circular ribbon was strikingly large in size spanning 650" in north-south and 500" in east-west direction. It showed the well-known sequential brightening in the clockwise direction during the decay phase of the M2.6 flare at the estimated speed of 160.7 km s-1. The quasi-circular ribbon also showed the radial expansion, especially in the southern part. Interestingly, at the time of the later M2.6 flare, the third flare ribbon parallel to the early two-ribbon structure also developed near the unipolar sunspot, then showed a typical separation in pair with the eastern most ribbon of the early two ribbons. The potential field reconstruction based on the PFSS model showed a fan shaped magnetic configuration including fan-like field lines stemming from the unipolar spot and fanning out toward the background decayed field. This large-scale fan-like field overarched full active region, and the footpoints of fan-like field lines were co-spatial with the observed quasi-circular ribbon. From the NLFF magnetic field reconstruction, we confirmed the existence of a twisted flux rope structure in the bipolar spot group before the first M2.0 flare. Hard X-ray emission signatures were detected at the site of twisted flux rope during the pre-flare phase of the M2.0 flare. Based on the analysis of both two-ribbon structure and quasi-circular ribbon, we suggest that a tether-cutting reconnection between sheared arcade overarching the twisted flux rope embedded in a fan-like magnetic field may have triggered the first M2.0 flare, then secondary M2.6 flare was introduced by the fan-spine reconnection because of the interaction between the expanding field and the nearby quasi-null and formed the observed large-scale quasi-circular flare ribbon.

  • PDF