• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.271-272
• /
• 2012

Bulk Metallic Glasses (BMGs or amorphous alloy) exhibit high strength and good corrosion resistance. Applications of thin films and micro parts of BMGs have been used a lot since its inception in the research of BMGs. However, Application and fabrication of BMGs are limited to make structural materials. Thin films of BMGs which is sputtered on the surface of structural materials by sputtering process is used to improve limits about application of BMGs. In order to investigate the difference of properties between designed alloys and thin films, we identified that thin films deposited on the surface that have the characteristic of the amorphous films and the composition of designed alloys. Zr-Cu (Cu=30, 35, 38, 40, 50 at.%) and Zr-Cu-Al (Al=10 at.% fixed, Cu=26, 30, 34, 38 at.%) alloys were fabricated with Zr (99.7% purity), Cu (99.997% purity), and Al (99.99% purity) as melting 5 times by arc melting method before rods 2mm in diameter was manufactured. In order to analyze GFA (Glass Forming Ability), rods were observed by Optical Microscopy and SEM and $T_g$, $T_x$, ($T_x$ is crystallization temperature and $T_g$ is the glass transition temperature) and Tm were measured by DTA and DSC. Powder was manufactured by Gas Atomizer and target was sintered using powder in large supercooled liquid region ($=T_x-T_g$) by SPS(Spark Plasma Sintering). Amorphous foil was prepared by RSP process with 5 gram alloy button. The composition of the foil and sputtered thin film was analyzed by EDS and EPMA. In the result of DSC curve, binary alloys ($Zr_{62}Cu_{38}$, $Zr_{60}Cu_{40}$, $Zr_{50}Cu_{50}$) and ternary alloys ($Zr_{64}Al_{10}Cu_{26}$, $Zr_{56}Al_{10}Cu_{34}$, $Zr_{52}Al_{10}Cu_{38}$) have $T_g$ except for $Zr_{70}Cu_{30}$ and $Zr_{60}Al_{10}Cu_{30}$. The compositions with $T_g$ made into powders. Figure shows XRD data of thin film showed similar hollow peak.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.1
• /
• pp.64-73
• /
• 2007

The catalytic activity of transition metals (Cu, Co, Mn, Fe and Ni) supported on ${\gamma}-Al_2O_3$ for the oxidation of toluene was investigated in the microreactor of fixed-bed type. The catalytic activity of transition metals for the oxidation of toluene turned out to be increasing in the order of Ni$Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene increased with the increasing loadings of copper, reached the maximum activity at 5% loadings of copper, and decreased with higher loadings of copper in the catalysts. The activity of $Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene decreased with the increasing calcination temperatures. This might result from the decreasing surface area of catalysts due to the sintering of copper oxide as well as ${\gamma}-Al_2O_3$ supports. The 5wt% $Cu/{\gamma}-Al_2O_3$ catalysts calcined at $400^{\circ}C$ for 4 hrs in the air showed the highest activity for the oxidation of toluene. Mutual inhibition was observed for the binary mixture of toluene and xylene. The activity of the easy-to-oxidize toluene was greatly decreased while the difficult-to-oxidize xylene was slightly decreased in the binary mixture of toluene and xylene. It might suggest that the inhibition of toluene and xylene in the binary mixture resulted from the competitive adsorption for the adsorbed oxygen on the catalytic surface.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.1
• /
• pp.60-67
• /
• 2020

In this study, copper (II) oxide powder for electroplating was prepared by recovering CuCl₂ from NaClO₃ type etching wastes via recovered non-sintering two step chemical reaction. In case of alkali copper carbonate [mCuCo₃·nCu(OH)₂], first reaction product, CuCo₃ is produced more than Cu(OH)₂ when the reaction molar ratio of sodium carbonate is low, since m is larger than n. As the reaction molar ratio of sodium carbonate increased, m is larger than n and Cu(OH)₂ was produced more than CuCO₃. In the case of m has same values as n, the optimum reaction mole ratio was 1.44 at the reaction temperature of 80℃ based on the theoretical copper content of 57.5 wt. %. The optimum amount of sodium hydroxide was 120 g at 80℃ for production of copper (II) oxide prepared by using basic copper carbonate product of first reaction. At this time, the yield of copper (II) oxide was 96.6 wt.%. Also, the chloride ion concentration was 9.7 mg/L. The properties of produced copper (II) oxide such as mean particle size, dissolution time for sulfuric acid, and repose angle were 19.5 mm, 64 second, and 34.8°, respectively. As a result of the hole filling test, it was found that the copper oxide (II) prepared with 120 g of sodium hydroxide, the optimum amount of basic hydroxide for copper carbonate, has a hole filling of 11.0 mm, which satisfies the general hole filling management range of 15 mm or less.

• Journal of Environmental Science International
• /
• v.28 no.1
• /
• pp.55-64
• /
• 2019

The adsorption properties of $Cs^+$ and $Cu^{2+}$ ions were evaluated by using a polysulfone scoria zeolite (PSf-SZ) composite with synthetic zeolite synthesized from Jeju volcanic rocks (scoria). In order to investigate the adsorption properties, various parameters, such as pH, contact time, reaction rate, concentration, and temperature in aqueous solutions, were evaluated by tests carried out in batch experiments. The adsorption capacities of $Cs^+$ and $Cu^{2+}$ ions increased between pH 2 but achieved equilibrium at pH 4 and above. The adsorption rate increased rapidly up to the initial 24 h, after which it plateaued ; the adsorption rate then sustained at equilibrium from 48 h. The adsorption kinetics of $Cs^+$ and $Cu^{2+}$ ions were described better by the pseudo-second-order kinetic model than the pseudo-first-order kinetic model. The Langmuir model fitted the adsorption isotherm data better than the Freundlich model. The maximum adsorption capacities of $Cs^+$ and $Cu^{2+}$ ions obtained from the Langmuir model were 53.8 mg/g and 84.7 mg/g, respectively. The calculated thermodynamic parameters showed that the adsorption of $Cs^+$ and $Cu^{2+}$ ions on PSf-SZ was feasible, spontaneous and endothermic reaction.

• Journal of Periodontal and Implant Science
• /
• v.52 no.1
• /
• pp.54-64
• /
• 2022

Purpose: This in vitro study was conducted to evaluate the effects of different debridement techniques and conditioning procedures on root surface morphology and blood clot stabilization. Methods: Two debridement techniques (curette [CU] vs. high-speed ultrasound [US]) and 2 conditioning procedures (ethylenediaminetetraacetic acid [EDTA] and phosphoric acid [PA]) were used for the study. Seven experimental groups were tested on root surfaces: 1) no treatment (C); 2) CU; 3) US; 4) CU+EDTA; 5) US+EDTA; 6) CU+PA; and 7) US+PA. Three specimens per group were observed under scanning electron microscopy (SEM) for surface characterization. Additional root slices received a blood drop, and clot formation was graded according to the blood element adhesion index by a single operator. Data were statistically analyzed, using a threshold of P<0.05 for statistical significance. Results: The C group displayed the most irregular surface among the tested groups with the complete absence of blood traces. The highest frequency of blood component adhesion was shown in the CU+EDTA group (P<0.05), while no differences were detected between the CU, US+EDTA, and CU+PA groups (P<0.05), which performed better than the US and US+PA groups (P<0.05). Conclusions: In this SEM analysis, EDTA and conventional manual scaling were the most efficient procedures for enhancing smear layer removal, collagen fiber exposure, and clot stabilization on the root surface. This technique is imperative in periodontal healing and regenerative procedures.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.161-164
• /
• 2001

Transmuted impurity atoms formed in neutron-irradiated ZnO thin films were theoretically identified first and then experimentally confirmed by Photoluminescence (PL). ZnO thin films grown by plasma-assisted molecular beam epitaxy were irradiated by neutron beam at room temperature. Among eight isotropes naturely exiting in ZnO films, only $^{64}Zn$, $^{68}Zn$, $^{70}Zn$ and $^{18}O$ were expected to transmute into $^{65}Cu$, $^{69}Ga$, $^{71}Ga$ and $^{19}F$, respectively. The concentrations of these transmuted atoms were estimated by considering natural abundance, neutron fluence, and neutron cross section. The neutron-irradiated ZnO thin films were characterized by PL. In the PL spectra of these ZnO thin film, the Cu-related PL peaks were seen, but the Ga- or F-associated PL peaks were absent. This observation demonstrates the existence of $^{65}Cu$ in the ZnO. In this paper, emission mechanism of Cu impurities wil1 be described and the reason for the absence of the Ga- or F-associated PL peaks will be discussed.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.717-723
• /
• 1998

The concentrations and wet deposition flux into the sea of heavy metals of precipitation in Pusan area were measured and estimated. The samples were collected by polyethylene bottle(30ι) from January to November in 1996, and heavy metals were analyzed by atomic absorption spectrometer. The concentration order of heavy metals was Al ＞Fe ＞Zn ＞Pb ＞Mn ＞Cu ＞Ni ＞Cd ＞Co, and they were high at inland sites and low at coastal sites. The enrichment factors for some metals(Zn, Cu, Pb, Cd), based on crustal Al, were significantly greater than unity, and the order was Cd ＞ Pb ＞ Zn ＞ Cu. This evidence suggests Cd and Pb are derived predominantly from non-crustal sources. Al, Fe and Mn contents showed good correlation with each other. Therefore this enrichment factor indicates similar geochemical behavior of these elements. The annual wet depositional flux(mg/ $m^2$ /yr) from Pl site was as follows: Al(121.1). Fe,(177.2), Zn(12.9), Mn(6.19), Pb(14.4), Cu(0.64), Ni(1.03), Cd(1.02) and Co(1.01).

• Journal of Korea Foundry Society
• /
• v.28 no.1
• /
• pp.31-36
• /
• 2008

Ti-Ni-Cu alloys are very attractive shape memory alloys for applications as actuators because of a large transformation elongation and a small transformation hysteresis. Rapidly solidified Ti-Ni alloy ribbons have been known to have the shape memory effect and superelasticity superior to the alloy ingots fabricated by conventional casting. In this study, solidification structures and shape memory characteristics of $Ti-Ni_{30}-Cu_{20}$ alloy ribbons prepared by melt spinning were investigated by means of DSC and XRD. Operating parameters to fabricate the amorphous ribbons were the wheel velocity of 55 m/s and the melt spinning temperature of $1500^{\circ}C$. The crystallization temperature was measured to be $440^{\circ}C$. The crystallized ribbons exhibited very fine microstructure after annealing at $440^{\circ}C$ for 10 minutes and $460^{\circ}C$ for 5 minutes and was deformed up to about 6.8% and 6.23% in ductile manner, respectively. Stress-strain curve of the ribbon exhibited a flat stress-plateau at 64 MPa and this is associated with the stress-induced a B2-B19 martensitic transformation. During cycle deformation with the applied stress of 220 MPa, transformation hysteresis and elongation associated with the B2-B19 transformation were observed to be $4.3^{\circ}C$ and 3.6%.

• Korean Journal of Crystallography
• /
• v.11 no.3
• /
• pp.137-146
• /
• 2000

The stoichiometric mix of evaporating materials for he CuInS₂ single crystal thin films was prepared. To obtain the single crystal thin films, CuINS₂ mixed crystal was deposited on etched semi-insulator GaAs(100) substrate by the hot wall epitaxy(HWE) system. The source and substrate temperature were 640℃ and 430℃, respectively and the thickness of the single crystal thin films was 2 ㎛. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction(DCXD). The carrier density and mobility deduced from Hall data are 9.64x10/sup 22//㎥ and 2.95x10/sup -2/ ㎡/V·s, respectively at 293 K. he optical energy gap was found to be 1.53 eV at room temperature. From the photocurrent spectrum obtained by illuminating perpendicular light on the c-axis of the thin film, we have found that the values of spin orbit coupling splitting ΔSo and the crystal field splitting ΔCr were 0.0211 eV and 0.0045 eV at 10K, respectively. From PL peaks measured at 10K, were can assign the 807.7 nm (1.5350 eV) peak to E/sub x/ peak of the free exciton emission, the 810.3 nm(1.5301 eV) peak to I₂ peak of donar-bound exciton emission and the 815.6 nm(1.5201 eV) peak to I₁ peak of acceptor-bound excition emission. In addition, the peak observed at 862.0 nm(1.4383 eV) was analyzed to be PL peak due to donor-acceptor pair(DAP).

• Korean Journal of Environmental Agriculture
• /
• v.19 no.3
• /
• pp.247-251
• /
• 2000

This study was conducted to investigate tissue nutrient contents and salt accumulation in plastic house soils cultivating lily, rose and carnation. The soil tested had high total salts, available phosphate and exchangeable potassium. The soil cultivating rose had highest salt concentvation followed by chose of carnation and lily. Tissue nutrient contents of lily were higher than chose of carnation and rose. In comparison among cultivars, the nutrient contents were as follows; 'Snow Qeen'>'Le Reve'>'Casa Blanca' in lily; 'Marina'>'Super star'>'Mary Devor'>'Madelon' in carnation; and 'Cocktail'> 'Marina'>'Maderon' in rose. The range of the nutrient contents were: T-N: $1.66\;{\sim}2.35%$, K: $1.73{\sim}2.23%$, Zn: $2.13{\sim}6.43\;mg/kg$, Cu: $3.79{\sim}13.89\;mg/kg$ in carnation; T-N: $0.79{\sim}1.65%$, P: $0.18{\sim}0.44%$, Ca: $0.59{\sim}1.26%$, Mg: $0.21{\sim}0.46%$, Zn: $23.65{\sim}90.30\;mg/kg$, Cu: $0.99{\sim}4.62\;mg/kg$ in lily; and T-N: $0.75{\sim}1.62%$, P: $0.17{\sim}0.30%$, K: $1.60{\sim}2.91%$, Ca: $0.64{\sim}0.94%$, Zn: $24.57{\sim}48.31\;mg/kg$, Cu: $3.10{\sim}9.08\;mg/kg$ in rose. The amount of nutrients uptake per plant was high in order of: K > T-N > Ca > Mg in lily; and T-N > K > Ca > P > Mg in rose.