Browse > Article
http://dx.doi.org/10.9725/kstle.2006.22.3.155

A Study on Engine Durability Considering Oil Consumption and Wear of Piston-Ring Pack and Cylinder Bore  

Chun Sang-Myung (Dept. of Automotive Engineering, Hoseo University)
Publication Information
Tribology and Lubricants / v.22, no.3, 2006 , pp. 155-163 More about this Journal
Abstract
Ring, groove and cylinder bore wear may not be a problem in most current automotive engines. However, a small change in ring face, groove geometry and cylinder bore diameter can significantly affect the lubrication characteristics and ring axial motion. This in turn can cause to change inter-ring pressure, blowby and oil consumption in an engine. Therefore, by predicting the wear of piston ring face, ring groove and cylinder bore altogether, the changed ring end gap and the changed volume of gas reservoir can be calculated. Then the excessive oil consumption can be predicted. Being based on the calculation of gas flow amount by the theory of piston ring dynamics and gas flow, and the calculation of oil film thickness and friction force by the analysis of piston ring lubrication, the calculation theory of oil amount through top ring gap into combustion chamber will be set. This is estimated as engine oil consumption. Furthermore, the wear theories of ring, groove and cylinder bore are included. Then the each amount of wear is to be obtained. The changed oil consumption caused by the new end gap and the new volume of oil reservoir around second land, can be calculated at some engine running interval. Meanwhile, the wear amount and oil consumption occurred during engine durability cycle are compared with the calculated values. Next, the calculated amount of oil consumption and wear are compared with the guideline of each part's wear and oil consumption. So, the timing of part repair and engine life cycle can be predicted in advance without performing engine durability test. The wear data of rings, grooves and cylinder bore are obtained from three engines before and after engine durability test. The calculated wear data of each part are turn out to be around the band of averaged test values or a little below.
Keywords
ring face wear; ring end gap; ring groove wear; cylinder bore wear; oil consumption; durability; piston-ring pack;
Citations & Related Records
Times Cited By KSCI : 2  (Citation Analysis)
연도 인용수 순위
1 Taylor, G. I., 'Deposition of a Viscous Fluid on the Wall of a Tube,' Journal of Fluid Mechanics, Vol. 10, pp. 161-165, 1961   DOI
2 Ting, L. L. and Mayer, J. E., Jr., 'Piston Ring Lubrication and Cylinder Bore Wear Analyses, Part I-Theory,' J. Lubr. Technol., 96F, p. 305, 1974
3 Ting, L. L., 'Lubricated Piston Rings and Cylinder Wear,' Wear Control Hand Book, edited by M. B. Peterson and W. O. Winer, ASME, New York, N. Y. pp. 609-665, 1980
4 Ting, L. L. and Mayer, J. E., Jr., 'Piston Ring Lubrication and Cylinder Bore Wear Analyses, Part II-Theory Verification,' J. Lubr. Technol., 96F, p. 258, 1974
5 Chun, S. M., 'A Basic Study on Piston-Ring Pack,' Journal of the KSTLE, Vol. 21, No.2, pp. 83-92, 2005   과학기술학회마을
6 Chun, S. M., 'A Study on Engine Oil Consumption,' Journal of the KSTLE, Vol. 21, No.6, pp. 296-301, 2005   과학기술학회마을
7 Greenwood J. A. and Tripp J. H., 'The Contact of Two Nominally Flat Rough Surface,' Proc. ImechE, Vol. 185, pp. 625-633, 1971
8 Schneider, E. W., Blossfeld, D. H. and Balnaves, M. A., 'Effect of Speed and Power Output on Piston Ring Wear in a Diesel Engine,' SAE Trans. 880672, 1988
9 Hoult, D. P. and Shaw II, B. T., 'The Puddle Theory of Oil Consumption,' Tribology Transactions, Vol. 37, No. 1, pp. 75-82, 1994   DOI   ScienceOn
10 Chung, Y., Chun, S. M., Kim, S. I., and Brombolich, L. J., 'Adhesive Wear Model of Piston Ring for a Diesel Engine,' Proceedings on 1994 KSAE Fall Conference, KSAE 943885, pp. 56-67, 1994