Browse > Article
http://dx.doi.org/10.12989/scs.2020.36.3.321

Bolted connectors with mechanical coupler embedded in concrete: Shear resistance under static load  

Milicevic, Ivan (Faculty of Civil Enginering, Univercity of Belgrade)
Milosavljevic, Branko (Faculty of Civil Enginering, Univercity of Belgrade)
Pavlovic, Marko (Faculty of Civil Engineering and Geosciences, Delft University of Technology)
Spremic, Milan (Faculty of Civil Enginering, Univercity of Belgrade)
Publication Information
Steel and Composite Structures / v.36, no.3, 2020 , pp. 321-337 More about this Journal
Abstract
Contemporary design and construction of steel-concrete composite structures employs the use of prefabricated concrete elements and demountable shear connectors in order to reduce the construction time and costs and enable dismantling of elements for their potential reuse at the end of life of buildings. Bolted shear connector with mechanical coupler is presented in this paper. The connector is assembled from mechanical coupler and rebar anchor, embedded in concrete, and steel bolt, used for connecting steel to concrete members. The behaviour and ultimate resistance of bolted connector with mechanical coupler in wide and narrow members were analysed based on push-out tests and FE analyses conducted in Abaqus software, with focus on concrete edge breakout and bolt shear failure modes. The effect of concrete strength, concrete edge distance and diameter and strength of bolts on failure modes and shear resistance was analysed. It was demonstrated that premature failure by breakout of concrete edge occurs when connectors are located 100 mm or closer from the edge in low-strength and normal-strength reinforced concrete. Furthermore, the paper presents a relatively simple model for hand calculation of concrete edge breakout resistance when bolted connectors with mechanical coupler are used. The model is based on the modification of prediction model used for cast-in and post-installed anchors loaded parallel to the edge, by implementing equivalent influence length of connector with variable diameter. Good agreement with test and FE results was obtained, thus confirming the validity of the proposed method.
Keywords
steel-concrete composite structures; shear connectors; mechanical couplers; shear resistance; concrete edge breakout resistance; finite element analysis;
Citations & Related Records
Times Cited By KSCI : 4  (Citation Analysis)
연도 인용수 순위
1 Brambilla, G., Lavagna, M., Vasdravellis, G. and Castiglioni, C.A. (2019), "Environmental benefits arising from demountable steel-concrete composite floor systems in buildings", Resources, Conservation & Recycling, 141, 133-142. https://doi.org/10.1016/j.resconrec.2018.10.014   DOI
2 CEB-FIP (2011), "Design of Anchorages in Concrete (fib Bulletin 58)", International Federation for Structural Concrete (fib); Lausanne, Switzerland.
3 Dallam L.N. (1968), "High strength bolts shear connectors - pushout tests", ACI J. Proc., 65(9):767-769
4 Dedic, D.J. and Klaiber, W.F. (1984), "High-strength bolts as shear connectors in rehabilitation work", Concr. Int., 6(7), 41-46.
5 Dai, X.H., Lam, D. and Saveri, E. (2015), "Effect of concrete strength and stud collar size to shear capacity of demountable shear connectors", J. Struct. Eng., 141(11), 04015025:1-10. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001267.   DOI
6 Eurocode 2 (2004), Design of concrete structures. Part 1.1: General rules and rules for buildings, European Committee for Standardization (CEN); Brussels, Belgium.
7 Eurocode 3 (2005), Design of steel structures. Part 1.8: Design of joints, European Committee for Standardization (CEN); Brussels, Belgium.
8 Eurocode 4 (2004), Design of composite steel and concrete structures. Part 1.1: General rules and rules for buildings, European Committee for Standardization (CEN); Brussels, Belgium.
9 Milosavljevic, B., Milicevic, I., Pavlovic, M. and Spremic, M. (2018), "Static behaviour of bolted shear connectors with mechanical coupler embedded in concrete", Steel Compos. Struct., 29(2), 257-272. https://doi.org/10.12989/scs.2018.29.2.257.   DOI
10 Oehlers, D.J. (1980), "Stud shear connectors for composite beams", Ph.D. Dissertation; University of Warwick, Coventry CV4 7AL, UK.
11 Okada J., Teruhiko, Y. and Lebet, J.P. (2006), "A study of the grouped arrangements of stud connectors on shear strength behaviour", Struct. Eng. Earthq. Eng., 23(1), 75-89. https://doi.org/10.2208/jsceseee.23.75s.
12 Ollgaard, J.G., Slutter, R.G. and Fisher, J.W. (1971), "Shear strength of stud connectors in lightweight and normalweight concrete", Eng. J. Amer. Inst. Steel Constr., 8(2), 55-64.
13 Pallares, L. and Hajjar, J.F. (2010), "Headed steel stud anchors in composite structures, part I: shear", J. Constr. Steel Res., 66(2), 198-212. https://doi.org/10.1016/j.jcsr.2009.08.009.   DOI
14 Pathirana, S.W., Uy, B., Mirza, O. and Zhu, X. (2016), "Bolted and welded connectors for rehabilitation of composite beams", J. Constr. Steel Res., 125, 61-73. https://doi.org/10.1016/j.jcsr.2016.06.003.   DOI
15 Pavlovic M., Markovic Z., Veljkovic M. and Budjevac D. (2013), "Bolted shear connectors vs. headed studs behaviour in push-out tests", J. Constr. Steel Res., 88, 134-149. https://doi.org/10.1016/j.jcsr.2013.05.003   DOI
16 Pavlovic, M. (2014), "Resistance of Bolted Shear Connectors in Prefabricated Steel-Concrete Composite Decks, Ph.D. Dissertation; University of Belgrade, Belgrade, Serbia.
17 Pavlovic, M. and Veljkovic, M. (2017), "FE validation of push-out tests", Steel Constr. Des. Res., 10(2), 135-144. https://doi.org/10.1002/stco.201710017.   DOI
18 Grosser, P. (2012), "Load-bearing behavior and design of anchorages subjected to shear and torsion loading in uncracked concrete", Ph.D. Dissertation; Institut fur Werkstoffe im Bauwesen der Universitat Stuttgart, Stuttgart, Germany.
19 Hawkins, N. (1987), "Strength in shear and tension of cast-in-place anchor bolts", Anchorage Concr., SP-103, 233-255.
20 Guezouli, S., Lachal, A. and Nguyen, Q.H. (2013), "Numerical investigation of internal force transfer mechanism in push-out tests", Eng. Struct., 52, 140-152. http://dx.doi.org/10.1016/j.engstruct.2013.02.021   DOI
21 Kwon, G. (2008), "Strengthening existing steel bridge girders by the use of post-installed shear connectors", Ph.D. Dissertation; The University of Texas at Austin, Austin, Texas, USA.
22 Lam, D., Dai, X., Ashour, A. and Rahman, N. (2017), "Recent research on composite beams with demountable shear connectors", Steel Constr. Des. Res., 10(2), 125-134. https://doi.org/10.1002/stco.201710016.   DOI
23 Lee, M. and Bradford, M.A. (2013), "Sustainable composite beam behaviour with deconstructable bolted shear connectors", Proceedings of the Composite Construction in Steel and Concrete VII, Palm Cove, Australia, July. https://doi.org/10.1061/9780784479735.034.
24 Liu, X., Bradford, M. and Lee, M. (2014), "Behavior of High-Strength Friction-Grip Bolted Shear Connectors in Sustainable Composite Beams", J. Struct. Eng., 141(6), 04014149:1-12. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001090.
25 Marshall, W.T., Nelson, H.M. and Banerjee, H.K. (1971), "An experimental study of the use of high-strength friction-grip bolts as shear connectors in composite beams", Struct. Eng., 49(4), 171-178.
26 Milosavljevic, B. (2013), "Theoretical and experimental research of the behaviour of reinforced concrete and steel element connection by rebar couplers", Ph.D. Dissertation; University of Belgrade, Belgrade, Serbia.
27 Spremic, M., Pavlovic, M., Markovic, Z., Veljkovic, M. and Budjevac, D. (2018), "FE validation of the equivalent diameter calculation model for grouped headed studs", Steel Compos. Struct., 26(3), 375-386. https://doi.org/10.12989/scs.2018.26.3.375.   DOI
28 Schaap, B.A. (2004): Methods to develop composite action in non-composite bridge floor systems: Part I. MSc thesis, The University of Texas, Austin, Texas.
29 Spremic, M., Markovic, Z., Veljkovic, M. and Budjevac, D. (2013), "Push-out experiments of headed shear studs in group arrangements", Adv. Steel Constr., 9(2), 139-160. http://dx.doi.org/10.18057/IJASC.2013.9.2.4.
30 Spremic, M., Markovic, Z. and Veljkovic, M. (2017), "Recommendations for the design of grouped headed studs", Steel Constr. Des. Res., 10(2), 145-153. https://doi.org/10.1002/stco.201710018.   DOI
31 Xu, C., Sugiura, K., Wu, C. and Su, Q. (2012), "Parametrical static analysis on group studs with typical push-out tests", J. Constr. Steel Res., 72, 84-96.   DOI
32 Xue, D., Liu, Y., Yu, Z. and He, J. (2012), "Static behavior of multi-stud shear connectors for steel-concrete composite bridge", J. Constr. Steel Res., 74, 1-7. https://doi.org/10.1016/j.jcsr.2011.09.017.   DOI
33 Yang, F., Liu, Y., Jiang, Z. and Xin, H. (2018), "Shear performance of a novel demountable steel-concrete bolted connector under static push-out tests", Eng. Struct., 160, 133-146. https://doi.org/10.1016/j.engstruct.2018.01.005.   DOI
34 Yu-Hang, W., Jie, Y., Jie-Peng, L. and Chen, Y.F. (2019), "Shear behavior of shear stud groups in precast concrete decks", Eng. Struct., 187, 73-84. https://doi.org/10.1016/j.engstruct.2019.02.002.   DOI
35 Ataei, A., Bradford, M. and Liu, X. (2016), "Experimental study of composite beams having a precast geopolymer concrete slab and deconstructable bolted shear connectors", Eng. Struct., 114, 1-13. https://doi.org/10.1016/j.engstruct.2015.10.041   DOI