Browse > Article
http://dx.doi.org/10.7736/KSPE.2015.32.1.69

Effect of Oxidizer on the Polishing in Cadmium Telluride CMP  

Shin, Byeong Cheol (School of Mechanical Engineering, Pusan National University)
Lee, Chang Suk (School of Mechanical Engineering, Pusan National University)
Jeong, Hae Do (School of Mechanical Engineering, Pusan National University)
Publication Information
Journal of the Korean Society for Precision Engineering / v.32, no.1, 2015 , pp. 69-74 More about this Journal
Abstract
Cadmium telluride (CdTe) is being developed for thin film of the X-Ray detector recently. But a rough surface of the CdTe should be improved for resolution and signal speed. This paper shows the study on the improvement of surface roughness and removal rate by applying Chemical Mechanical Polishing. The conventional potassium hydroxide (KOH) based colloidal silica slurry could not realize a mirror surface without physical defects, resulting in low material removal rate and many scratches on surface. In order to enhance chemical reaction such as form oxidized layer on the surface of cadmium telluride, we used hydrogen peroxide ($H_2O_2$) as an oxidizer. Consequently, in case of 3 wt% concentration of hydrogen peroxide, the highest MRR (938 nm/min) and the lowest surface roughness ($R_{p-v}=10.69nm$, $R_a=0.8nm$) could be obtained. EDS was also used to confirm the generated oxide of cadmium telluride surface.
Keywords
Cadmium telluride; Chemical mechanical polishing; Hydrogen peroxide; Material removal rate; Surface roughness;
Citations & Related Records
Times Cited By KSCI : 2  (Citation Analysis)
연도 인용수 순위
1 Dendy, P. P. and Heaton, B., "Physics for Diagnostic Radiology," 2nd Ed., Taylor & Francis, pp. 192-216, 1999.
2 Shah, K. S., Bennett, P. R., Cirignano, L. J., Dmitriyev, Y. N., Klugerman, M. B., et al., "X-ray Imaging with Semiconductor Films," Proc. of SPIE's International Symposium on Optical Science, Engineering, and Instrumentation, International Society for Optics and Photonics, pp. 102-113, 1998.
3 Kasap, S. O. and Rowlands, J., "Direct-conversion flat-panel x-ray image detectors," IEE Proceedings-Circuits, Devices and Systems, Vol. 149, No. 2, pp. 85-96, 2002.   DOI
4 Ali, I., Roy, S. R., and Shinn, G., "Chemical-Mechanical Polishing of Interlayer Dielectric-A Review," Solid State Technology, Vol. 37, No. 10, 1994.
5 Kim, H. J., "A Study on the Interfacial Characteristics and Its Effect on Material Removal in CMP," Ph.D Thesis, Department of Precision and Mechanical Engineering, Pusan National Univ., 2003.
6 Lee, H. S., Park, B. Y., Kim, G. Y., Kim, H. J., Seo, H. D., and Jeong, H. D., "Effects of Friction Energy on Polishing Results in CMP Process," Trans. Korean Soc. Mech. Eng. A, Vol. 28, No. 11, pp. 1807-1812, 2004.   과학기술학회마을   DOI
7 Samsung Electronics CO., Ltd., "Non Selective Metal Slurry for CMP and its CMP Method," KOR Patent, No. 2001-0035669, 2001.
8 Park, B. Y., Lee, H. S., Park, K. H., Jeong, S. H., Seo, H. D., et al., "A Study on Oxidizer Effects in Tungsten CMP," Journal of the Korean Institute of Electrical and Electronic Material Engineers, Vol. 18, No. 9, pp. 787-792, 2005.   과학기술학회마을   DOI
9 Shin, B. C., Lee, Y. K., Lee, H. J., Kim, H. J., and Jeong, H. D., "Effect of Hydrogen Peroxide for Removal Rate on Cadmium Telluride Chemical Mechanical Planarization," International Conference on Planarization Technology, pp. 188-191, 2013.
10 Jeong, S., Lee, H., Cho, H., Lee, S., Kim, H., et al., "Effect of Additives for Higher Removal Rate in Lithium Niobate Chemical Mechanical Planarization," Applied Surface Science, Vol. 256, No. 6, pp. 1683-1688, 2010.   DOI