Browse > Article

Prediction and Control of Welding Deformation for Panel Block Structure  

Kim, Sang-Il (Okpo Office, Lloyd's Resister Asia)
Publication Information
Journal of Ocean Engineering and Technology / v.22, no.6, 2008 , pp. 95-99 More about this Journal
Abstract
The block assembly of ship consists of a certain type of heat processes such as cutting, bending welding residual stress relaxation and fairing. The residual deformation due to welding is inevitable at each assembly stage. The geometric inaccuracy caused by the welding deformation tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding deformation. The validity of the prediction method must be also clarified through experiments. This paper proposes a simplified analysis method to predict the welding deformation of panel block structure. For this purpose, a simple prediction model for fillet welding deformations has been derived based on numerical and experimental results through the regression analysis. On the basis of these results, the simplified analysis method has been applied to some examples to show its validity.
Keywords
Welding deformation; Geometric inaccuracy; Simplified analysis method; Simple prediction model; Regression analysis;
Citations & Related Records
Times Cited By KSCI : 3  (Citation Analysis)
연도 인용수 순위
1 Kim, S.I., Han J.M., Cho, Y.K., Kang, J.K., Lee, J.Y. and Lee, J.S. (1997). 'A Study on the Accuracy Control of Block Assembly in Shipbuilding - Simulation of Residual deformation due to Fillet Welding -', Proceedings of ICCAS-1997, pp 367-381
2 Lee, S.G. (1992). Modeling of Residual Stress in Thick Section Weldments, Ph.D. Thesis, Department of Welding Engineering, University of Ohio State
3 Nomoto, T., Aoyarna, K. and Tachechi, S. (1997). 'Basic Studies on Accuracy Management System for Shipbuilding', Proceedings of ICCAS'97, pp 323-338
4 Ueda, Y., Murakawa, H., Gu, S.M., Okumoto, Y. and Kamichika, R (1992). 'Simulation of Welding Deformation for Accurate Ship Assembling(1st Report)', Journal of the Society of Naval Architects of Japan, Vol 171, pp 395-404
5 김상일 (1999). 선체 구조의 용접변형 제어법 개발, 울산대학교 공학박사학위논문
6 김상일 (2003). 'FPSO선 Moon Pool 구조의 용접변형 해석에 관한 연구', 한국해양공학회지, Vol 17, No 3, pp 27-32
7 Lee, J.S. (1998). 'A Study on the Production-oriented Structural Design Information System of Panel Blocks', Proceedings of PRADS'98, pp 359-364
8 Nomoto, T., Ohmori, T., Sutoh, T., Enosawa, M., Aoyarna, K. and Saitoh, M. (1990). 'Development of Simulator for Plate Bending by Line Heating', Journal of the Society of Naval Architects of Japan, Vol 168, pp 527-535
9 이주성, 김상일, 오석진 (1994). '선상가열법에 의한 강판의 곡 가공 자동화 시스템(I)', 대한조선학회논문집, Vol 31, No 4, pp 139-146
10 이주성 (2004). '평 블록의 용접변형 제어에 관한 연구', 한국해양공학회지, Vol 18, No 1, pp 35-40
11 Ueda, Y., Kim, Y.C., Yamakita, T. and Bang, H.S. (1988). 'Applicability of Substituting Plane-deformation Problems for Three-dimensional Thermal Elasto-Plastic Problems', Transactions of the Japanese Welding Society, Vol 6, No 1, pp 47-59   DOI
12 이주성, 박재우 (2008). '박판 필릿 용접 시 변형 제어를 위한 장력법 적용', 한국해양공학회지, Vol 22, No 1, pp 64-69   과학기술학회마을