Browse > Article
http://dx.doi.org/10.3795/KSME-B.2009.33.1.17

Analysis of Heat Transfer in Cooling of a Hot Plate by Planar Impingement Jet  

Ahn, Dae-Hwan (포항공과대학교 기계공학과)
Kim, Dong-Sik (포항공과대학교 기계공학과)
Publication Information
Transactions of the Korean Society of Mechanical Engineers B / v.33, no.1, 2009 , pp. 17-27 More about this Journal
Abstract
Water jet impingement cooling is used to remove heat from high-temperature surfaces such as hot steel plates in the steel manufacturing process (thermo-mechanical cooling process; TMCP). In those processes, uniform cooling is the most critical factor to ensure high strength steel and good quality. In this study, experiments are performed to measure the heat transfer coefficient together with the inverse heat conduction problem (IHCP) analysis for a plate cooled by planar water jet. In the inverse heat transfer analysis, spatial and temporal variations of heat transfer coefficient, with no information regarding its functional form, are determined by employing the conjugate gradient method with an adjoint problem. To estimate the two dimensional distribution of heat transfer coefficient and heat flux for planar waterjet cooling, eight thermo-couple are installed inside the plate. The results show that heat transfer coefficient is approximately uniform in the span-wise direction in the early stage of cooling. In the later stage where the forced-convection effect is important, the heat transfer coefficient becomes larger in the edge region. The surface temperature vs. heat flux characteristics are also investigated for the entire boiling regimes. In addition, the heat transfer rate for the two different plate geometries are compared at the same Reynolds number.
Keywords
Planar Impingement Jet; Heat Transfer Coefficient; Inverse Heat Conduction Problem; Accelerated Cooling Process;
Citations & Related Records
Times Cited By KSCI : 3  (Citation Analysis)
Times Cited By SCOPUS : 0
연도 인용수 순위
1 Choi, K. J. and Yao, S. C., 1987, “Mechanisms of Film Boiling Heat Transfer of Normally Impacting Spray”, Int. J. Heat Mass Transfer, Vol. 30, No. 2, pp. 311-318   DOI   ScienceOn
2 Wu, S. J., Shin, C. H. and Cho, H. H., 2004, “The Local Measurements of Single Phase and Boiling Heat Transfer by Confined Planar Impinging Jets”, Trans. of the KSME (B), Vol. 28, No. 8, pp. 895-901   과학기술학회마을   DOI   ScienceOn
3 Zumbrunnen, D. A., Incropera, F. P. and Viskanta, R., 1990, “Method and Apparatus for Measuring Heat Transfer Distributions on Moving and Stationary Plates Cooled by a Planar Liquid Jet”, Experimental Thermal and Fluid Science, Vol. 3, pp. 202-213   DOI   ScienceOn
4 Xu, F. and Gadala, M. S., 2006, “Heat Transfer Behavior in the Impingement Zone Under Circular Water Jet”, Int. J. Heat and Mass Transfer, Vol. 49, pp. 3785-3799   DOI   ScienceOn
5 Alifanov, O. M., 1994, “Inverse Heat Transfer Problems”, Springer-Verlag, Berlin
6 Beck, J. V., Blackwell, B. and Clair, C. R. ST. JR., 1985, “Inverse Heat Conduction Ill-Posed Problems”, A Wiley-Interscience Publication, New York
7 Ohkubo, H. and Nishio, S., 1990, “Study on Accurate Prediction of Heat Transfer Characteristics of Mist Cooling(Effects of Surface Wettability)”, JSME Int. Journal Series II, Vol. 33, No. 2, pp. 326-332
8 Buckingham, F. P. and Haji-Sheikh, A., 1995, “Cooling of High-Temperature Cylindrical Surfaces Using a Water-Air Spray”, Trans. of the ASME, Vol. 117, pp. 1018-1027   DOI
9 Vader, D. T., Incropera, F. P. and Viskanta, R., 1991, “A Method for Measuring Steady Local Heat Transfer to an Impinging Liquid Jet”, Experimental Thermal and Fluid Science, Vol. 4, pp. 1-11   DOI   ScienceOn
10 Lee, P. J., Choi, H. W. and Lee, S. H., 2003, “Effect of Nozzle Height on Heat Transfer of a Hot Steel Plate Cooled by an Impinging Water Jet”, Trans. of the KSME (B), Vol. 27, No. 5, pp. 668-676   과학기술학회마을   DOI   ScienceOn
11 Al-Ahamdi, H. M., Yao, S. C. and Kasperski, K., 2002, “Experimental Study on the Spray Cooling of High Temperature Metal Using Full Cone Industrial Sprays”, 2002 Steelmaking Conference Proceedings, pp. 365-374
12 Wang, T. Y. and Chen, C. C. P., 2003, “Thermal-ADI; A Linear-Time Chip-Level Dynamic Thermal-Simulation Algorithm Based on Alternating-Direction-Implicit(ADI) Method”, IEEE Trans. VLSI Systems, Vol. 11, No. 4, pp. 691-700   DOI   ScienceOn
13 Colaco, M. J. and Orlande, H. R. B., 1999, “Comparison of Different Versions of the Conjugate Gradient Method of Function Estimation”, Numerical Heat Transfer(Part A), Vol. 36, pp. 229-249   DOI   ScienceOn
14 Kim, W. S., Ozisik, M. N. and Choi, E. R., 1999, “Alternate Application of Regular and Modified Conjugated Gradient Method”, Hybrid Methods in Engineering, Vol. 1, No. 3, pp. 217-234
15 Kim, S. K. and Lee, W. I., 2004, “Implementation of Inverse Method for Estimating Undetermined Boundary in a Two-Dimensional Slab Based on Temperature Measurement”, Numerical Heat Transfer(Part A), Vol. 46, pp. 515-523   DOI   ScienceOn
16 Lee, P. J., Choi, H. W. and Lee, S. H., 2000, “The Effect of Ambient Air Condition on a Hot Steel Plate Cooled by Impinging Water Jet”, Trans. of the KSME (B), Vol. 24, No. 1, pp. 29-38   과학기술학회마을
17 Baonga, J. B., Louahlia-Gualous, H. and Imbert, M., 2006, “Experimental Study of the Hydrodynamic and Heat Transfer of Free Liquid Jet Impinging a Flat Circular Heated Disk”, Applied Thermal Engineering, Vol. 26, pp. 1125-1138   DOI   ScienceOn
18 Kang, D. H., Kwag, D. S., Kim, W. S. and Lee, Y. K., 2003, “A Study on the Estimation of One-Dimensional Heat Fluxes on the Slab in Reheating Furnace by Using Inverse Analysis”, Trans. of the KSME (B), Vol. 27, No. 1, pp. 61-68   과학기술학회마을   DOI   ScienceOn