Browse > Article List
학술지 정보
Journal of the Korean Society for Precision Engineering  

논문
1 Technical Trends of Worldwide Machine Tool Industries in JIMTOF2002
박종권;박영조; / Korean Society for Precision Engineering , v.19, no.12, pp.7-12,
2 Current Status of Machining Centers in IMTS 2002
김태형; / Korean Society for Precision Engineering , v.19, no.12, pp.13-19,
3 Ideal Phase map Extraction Method and Filtering of Electronic Speckle Pattern Interferometry
강영준;이주성;박낙규;권용기; / Korean Society for Precision Engineering , v.19, no.12, pp.20-26,
4 Development of Optical Fiber Coupled Displacement Probe Sensor with a New Compensation Method
;;;P. Sainsot;L. Flamand;; / Korean Society for Precision Engineering , v.19, no.12, pp.27-32,
5 A Study on Intelligent Generator of Optimal Process Conditions to Avoid Short Shot
강성남;허용정;조현찬; / Korean Society for Precision Engineering , v.19, no.12, pp.33-37,
6 Force Control of an Arm of Walking Training Robot Using Sliding Mode Controller
신호철;강창회;정승호;김승호; / Korean Society for Precision Engineering , v.19, no.12, pp.38-44,
7 Fine Gap Control Using Pneumatic Servo System
김동환;김영진;정대화; / Korean Society for Precision Engineering , v.19, no.12, pp.45-56,
8 Runout Control of a Magnetically Suspended High Speed Spindle Using Adaptive Feedforward Method
노승국;경진호;박종권; / Korean Society for Precision Engineering , v.19, no.12, pp.57-63,
9 Analysis of Optimal Dynamic Absorbing System Considering Human Behavior Induced by Transmitted Force
김효준;양현석;박영필;류봉조;최의중;이성배; / Korean Society for Precision Engineering , v.19, no.12, pp.64-69,
10 Event Based Tele-Operation with Variable Holding Time
박준영;박장현; / Korean Society for Precision Engineering , v.19, no.12, pp.70-77,
11 Analysis and Denoising of Cutting Force Using Wavelet Transform
하만경;곽재섭;진인태;김병탁;양재용; / Korean Society for Precision Engineering , v.19, no.12, pp.78-85,
12 Machining Verification Model Considering Feed Rate for Virtual Milling
백대균;고태조;김희술; / Korean Society for Precision Engineering , v.19, no.12, pp.86-92,
13 Experimental Verification of Aerosol Generation Mechanism for Cutting Fluid in Turning
고태조;오명석;박성호;김희술; / Korean Society for Precision Engineering , v.19, no.12, pp.93-99,
14 Development of Adult Authentication System using Numeral Recognition
김갑순;박중조; / Korean Society for Precision Engineering , v.19, no.12, pp.100-108,
15 Mechanism Design of Optical Pickup Actuator for Fast Access of Optical Disk Drive
박준혁;이상헌;백윤수; / Korean Society for Precision Engineering , v.19, no.12, pp.109-119,
16 Cutting Characteristics of Oxygen-Free Using the Ultra Precision Machining
고준빈;김건희;원종호; / Korean Society for Precision Engineering , v.19, no.12, pp.120-126,
17 A Study on Fatigue Life and Fatigue Crack Propagation Behavior of MMC
허선철;박원조;최용범; / Korean Society for Precision Engineering , v.19, no.12, pp.127-133,
18 Ultraprecision Polishing Technique for Micro 3-Dimensional Structures using ER Fluids
김욱배;이상조;김용준;이응숙; / Korean Society for Precision Engineering , v.19, no.12, pp.134-141,
19 A Experimental Study of Automobile Hub Clutch used Flow Control Forming Techniques
박종남;계중읍;김병민; / Korean Society for Precision Engineering , v.19, no.12, pp.142-149,
20 Predicting Cutting Forces in Face Milling with the Orthogonal Machining Theory
김국원; / Korean Society for Precision Engineering , v.19, no.12, pp.150-157,
21 Three-Dimensional Simulation of a Rotor Pole Forging Process and Verification of the Results
고병호;이민철;제진수;전만수; / Korean Society for Precision Engineering , v.19, no.12, pp.158-162,
22 Optimal Design and Control of xy${\theta}$ Fine Stage in Lithography System
김동민;김기현;이성규;권대갑; / Korean Society for Precision Engineering , v.19, no.12, pp.163-170,
23 A Study on the Micro Tool Fabrication using Electrolytic In-process Dressing
이현우;최헌종;이석우;최재영;정해도; / Korean Society for Precision Engineering , v.19, no.12, pp.171-178,
24 Development of a Portable Device based on PDA for Vibration Signal Analysis
김동준;박광호;기창두; / Korean Society for Precision Engineering , v.19, no.12, pp.179-184,
25 PC Based STEP-NC Milling Machine Operated by STEP-NC in XML Format
이원석;방영봉; / Korean Society for Precision Engineering , v.19, no.12, pp.185-193,