|
1 |
An Evaluation on Cutting Characteristics in Milling Process with Different Helix Angle Endmills
이상복;김원일;왕덕현;김실경;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.1-7,
|
|
2 |
On the Machinability of CFRP Composites Dependent on the Number of Stacking and Drill Diameter
정성택;박종남;조규재;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.8-13,
|
|
3 |
Estimation of Laser Welding Behavior of SM45C Steels by Plume Monitoring
유영태;김재열;노경보;양동조;오용석;임기건;김지환;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.14-21,
|
|
4 |
Fault Diagnosis of a Pump Using Analysis of Noise
박순재;이신영;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.22-28,
|
|
5 |
Design and Performance Test of Plate Type ER-Valve
장성철;염만오;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.29-35,
|
|
6 |
Analysis of Cutting Parameters for -hBN Machinable Ceramics Using Tungsten Carbide Tool
장성민;조명우;조원승;박동삼;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.36-43,
|
|
7 |
A Study on the Characteristics of Ultra-Precision Cutting for Al Alloy
김우순;김동현;난바의치;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.44-49,
|
|
8 |
Analysis of a Structural Damage Detection Using Sensitivity Analysis
이정윤;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.50-55,
|
|
9 |
An Experimental Study on Detection of Defects in Weldzone
남궁재관;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.56-63,
|
|
10 |
A Study on Spacecraft Alignment Measurement with Theodolite
윤용식;이동주;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.64-70,
|
|
11 |
Optimal Design of Panel with Trapezoidal Type Stiffeners
이종선;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.71-76,
|
|
12 |
A Study on the Adaptive Friction Compensator Design of a Hydraulic Proportional Position Control System
이명호;박형배;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.77-83,
|
|
13 |
A Study on the Cutting Force Simulation for Ball-end Milling Operation
홍민성;김종민;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.84-91,
|
|
14 |
A Study on the Optimization of Fuel-Cell Stack Design
홍민성;김종민;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.92-96,
|
|
15 |
A Study on Performance and Exhaust Emission with Bio-Diesel and ULSD at Heavy-Duty Diesel Engine
박만재;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.97-103,
|
|
16 |
An Experimental Study on Diesel Engine of Exhaust Emission Characteristics by Interface Unit
한영출;김대열;백두성;
/
The Korean Society of Manufacturing Technology Engineers
, v.12, no.6, pp.104-111,
|
|