오늘날 자동차용 엔진에 대한 사용자의 요구는 여러가지가 있지만 그 중에서도 손쉬운 운전, 고 출력화, 응답(response)의 향상 등의 요구는 지금 이후로도 계속되리라 생각된다. 슈퍼차저도 이러한 요구에 의하여 사용되고 있으며 이제는 엔진의 보조적 향상책으로 뿐만 아니라 엔진에 있어서 필요 불가결한 것으로써 확실히 정착되리라 생각된다. 본 고에서 살펴본 바에 의하면 스크류식 슈퍼차저가 테스트된 4종류의 슈퍼차저중에서 가장 나은 성능, 과급압, 토르크를 주고 있으며, 또한 가장 소형이며 경량이다. 또한 스크류로타는 팽창기로써 효율 높게 작용할 수 있어, 이의 채용으로 기존의 터보콤파운드시스템 보다 8-10% 에너지 효율이 높게됨이 알려지고 있다. 그러므로 스크류로타를 이용한 터보콤파운드시스템은 기존의 어떤 시스템보다도 효율이 높은 시스템으로 발전할 수 있는 가능성이 높아 이의 연구가 적극 추진되어야 하겠다.

1. 몬트리올 의정서. 2. 우리나라 오존층보호 규제. 3. 특정물질 사용감축 방안. 4. 우리나라 자동차업계의 대체냉매 에어컨 개발동향

본 고에서는 IP의 요구조건을 기능적인 면과 성능적인 면으로 나누어 설명하고 기능면에서는 소재의 물성을 평가하여 Guideline을 제시하고자하며 성능적인 면에서는 설계과정에서 사전에 성능을 평가하는 작업을 거침으로써 가능한 저렴한 재질로서 주어진 성능을 만족하고 또한 개발과정에서의 시행착오를 줄이는 방안을 제시하고자 한다.

In this study, the characteristics of decreasing exhaust gas of diesel engine was examined in dual fuel method by using commertial LPG for automotive. LPG was supplied to engine intake port by fumigation method and flow rate was controlled by using the needle valve. LPG supply ratios were 0, 20, 30% of total fuel amount to be supplied to engine by mass base. We investigated the effect of LPG supply ratio on exhaust gas concentrations related to excess air ratio and engine load at 1600, 1800, 2000 rpm. Soot concentration decreased about 30% in proportion to the increase of the LPG supply ratio. NOx concentration decreased in proportion to the increase of the LPG than diesel only and the increase rate was higher at low engine load. BSFC(Brake specific fuel consumption) was lower in proportion to the increase of the LPG supply ratio at high engine load and to the decrease of LPG supply ratio at low engine load.

A numerical modeling technique is proposed for computer simulations of high speed valve train dynamic terms in the valve spring reaction forces are calculated using linear vibration theory for given kinematic valve motions. Because the spring dynamics are analyzed before the time stepping integration, spring surge phenomena can be included without using additional computer time. In addition to that, steady state response of the valve dynamics can be obtained by just one cycle simulation. Consequently, valve train dynamics can be simulated very quickly without noticeable errors in accuracy. The experimental result prove the computer model developed here is accurate and also computationally efficient. The model is especially useful for cam profile optimizations.

In this study, the function of a hydraulic brake system with a vacuum booster is systematically analyzed according to the mutual relations which follow : - the brake pedal force vs. booster cylinder input force - the booster output force vs. master cylinder input force - the hydraulic line pressure vs. braking deceleration. A computer program is developed based on the theory which is able to predict and analyze the pedal force characteristics at the beginning of the initial stage of brake system design. Analytical results show good agreement with the experimental vehicle test.

The vibration characteristics of radial tire are studied. In order to obtain theoretical natural frequency and mode shape, the plane vibration of a tire is modeled to that of circular beam. By using the Tielking method based on Hamilton's principle, theoretical results are determined by considering tension force due to tire inflation pressure, rotational velocity and tangential, radial stiffness. Modal parameters varying the inflation pressure are determined experimentally by using the transfer function method. Results show that material property and wear are parameter for shifting of natural frequency and damping.

The dynamic behaviors of a launcher under impulsive forces are analyzed. All the components of the system, ie ; chassis, turret, cage and suspension parts, are modeled as rigid. The dynamic analysis code, which is developed with the formulae describing the system equations of motion in terms of relative quantities, is used to carry out the analysis. The results show the dynamic responses of chassis and cage when the driving constraints are imposed on turret and cage.

In the present study, the velocity profiles and entrance length of developing transitional pulsating flows are investigated both analytically and experimentally in the entrance region of a square duct. The systems of conservation equations for transitional pulsating flows in a square duct are solved analytically by linearizing the non-linear convective terms. Analytical solutions are obtained in the form of infinite series for velocity pofiles. The experimental study for the air flow in a square duct(40mm*40mm*4000mm) is carried out to measure velocity profiles and other parameters by using a hot-wire anemometer with a data acquisition and processing system. The distribution of velocity profiles( $u_{ps}$ / $u_{m,ta}$) in the decelerating period is higher than in the accelerating period. The distribution of the axial component of the axial component of velocity in the transitional flow is nearly uniform in the central region of the duct, and decrease rapidly near the wall. The entrance length correlation of the transitional pulsating flows in a square duct is obtained to be $L_{e}$/ $D_{h}$=0.83 $A_{1}$R $e_{ta}$ /(.omega. sup+1)$^{2}$TEX>

내연기관의 혼합 가스 생성 장치로 흡입되는 공기의 유량을 조절하기 위해 Butterfly 밸브가 사용 된다. 이 밸브는 유량의 제어에는 매우 유용한 반면, 밸브 후면에서의 복잡한 공기의 유동현상[6] 으로 인하여 혼합가스의 생성에 장해적인 요소를 제공하기도 한다. 특히 밸브가 많이 닫힌 상태 에서는 밸브와 관로벽 사이의 간격이 좁아지는 Throttling 현상으로 인하여, 엔진에 고 부하시 흡 입되는 공기의 양이 증가하게 되어, 밸브 주위에서 공기 속도의 급증으로 인하여 유동장의 압축 성 현상을 기대할 수 있다. Throttle의 Choking 현상으로 인하여 공기의 입자는 운동에너지를 잃 게 되고, 궁극적 혼합가스의 생성에 영향을 미쳐 엔진성능의 저하를 초래하게 된다. 본 연구에서 는 실제 엔진(Central Fuel Injection Engine, 5 liters) [1]의 흡인 manifold를 modelling하여, 특히 밸브가 많이 닫힌 상태에서, 밸브 주위에서의 난류 유동의 압축성 현상을 정량적으로 분석해 보았다.

Variable thickness plates are commonly encountered in the majority of mechanical/structural components of industrial applications. And, as a result of the unsymmetry of the structure or the load and the anisoptropy of the materials, the cracks in engineering structures are generally subjected to combined stresses. In spite of considerable practical interest, however, a few fracture mechanics study on combined mode crack in a variable thickness plate have carried out. In this respect, combined mode 1/3 stress intensity factors $K_{1}$ and $K_{3}$ at the crack tip for a variable thickness plate were obtained by 3-dimensional finite element analysis. Variable thickness plates containing a central slant crack were chosen. the parameters used in this study were dimensionless crack length .lambda. crack slant angle .alpha, thickness ratio .betha. and width ratio .omega. Stress intensity factors were calculated by crack opening displacement(COD) and crack tearing displacement(CTD) method proposed by Ingraffea and Manu. The effect of thickness ratio .betha. on $K_{1}$ is relatively great in comparison to $K_{3}$.

Plane strain punch stretching test (PSST) was developed to evaluate stamping formability of sheet materials. In this test, the rectangular specimen of sheet material is uniformly stretched up to fracture by raising a specially designed punch to certainly assure plane strain stretching deformation along the longitudinal direction of the specimen. The stamping formability was evaluated by limit punch height(LPH) in plane strain punch stretching test compared to limit dome height(LDH) in hemispherical punch stretching test. LPH-value in PSST well ranks the stamping formability of various material and correlates with press performance. Moreover by using ultrasonic thickness gauge the plane strain intercept-limit plane strain(FLCo)-in forming limit curve can be accurately determined from thickness measurement around the fracture area. The FLCo derived from thickness measurement well correlates with the results from circle grid analysis for the deformed circle grid marked on the surface of the specimen.

Engineering ceramics have some excellent properties as the material for the mechanical components. It is, however, very difficult to grind ceramics with high efficiency because of their high strength, hardness and brittleness. In this paper, experiments are carried out to obtain the effect of "In-process dressing" to grind the Engineering ceramics with high efficiency. To save running time for dressing process and obtain restraint effect of diamond grain wear, "In-process dressing" system using WA stick type honing stone is proposed. Representative Engineering ceramics, such as AI$_{2}$O$_{3}$, Si$_{3}$N$_{4}$, are ground with diamond wheel. Also bending strength test is carried out to check upward tendancy of mecahnical properties as the result of machining defact restraint through the grinding machining method using "In-process dressing" process. Some results obtained in this study provide useful information to attain the high efficiency grinding and the high mechanical properties of Engineering ceramics.rties of Engineering ceramics.